• Journal of the Korea Concrete Institute
• /
• v.25 no.1
• /
• pp.115-123
• /
• 2013

The steel industry, a representative industry that significantly consumes raw materials and energy, produces steel as well as a large amount of by-product steel slag through the production process. The vast habitat foundation of marine life has been destroyed due to recent reckless marine development and environment pollution, resulting in intensification of the decline of marine resources, and a solution to this issue is imperative. In order to propose a method to recycle large amounts of by-product slag into a material that can serve as an alternative to natural aggregate, the engineering properties and applicability for each mixing factor of environment friendly porous concrete as a material for the composition of marine ranches were evaluated in this study. The test results for percentage of voids per mixing ratio revealed that the margin of error for all conditions was within 2.5%. The compressive strength test results showed that the most outstanding environmental friendly porous concrete can be manufactured when mixing 30% slag aggregate and 10% specially treated granular fertilizer for the optimum volume fraction. As concrete for marine applications, the best seawater resistance was obtained with mixing conditions for high compression strength. An assessment of the ability to provide a marine life habitat foundation of environmentally friendly porous concrete showed that a greater percentage of voids facilitated implantation and inhabitation of marine life, and the mixing of specially treated granular fertilizer led to active initial implantation and activation of inhabitation. The evaluation of harmfulness to marine life depending on the mixture of slag aggregate and specially treated granular fertilizer revealed that the stability of fish is secured.

• Korean Journal of Food Science and Technology
• /
• v.26 no.3
• /
• pp.305-309
• /
• 1994

Precooked powder of redbean porridge (RP) was prepared by the series of process extrusion, drying, milling and blending with a mixture of whole redbean flour and corn starch and others. The optimum process and quality of products for RP were investigated. After extrusion under the moisture content 24 to 26%, twin screw speed 350 rpm, extrusion temperature 150 to $155^{\circ}C$ and feed rate 60 kg/hr, the product had a higher quality with its natural redbean flavor/color. During the extrusion process, extrusion temperature and specific mechanical energy increased from 150 to $198^{\circ}C$ and from 134 to 144 kwh/ton respectively, as the amount of addition water decreased from 6 to 2 kg/hr. By the hot air drying of redbean extrudate (RE). it could be dried below to 4% moisture content, of which level considered as an optimal moisture content for anti-caking of the powdered product, at $80^{\circ}C$ for 4hrs and at $100^{\circ}C$ for 1.5 hrs respectively. In the sieve analysis of extrudate powder, when the product milled through a mesh size of 0.5 mm or 1.0 mm, about 80% or 65% of the feed was passed a 65 mesh screen respectively. Moisture absorption of final blended products was formed a cake under 100% of relative humidity after 13 hrs of storage. As the amount of RE powder reduced, the flavor score of products decreased by sensory evaluation of products prepared by the different ratio of RE powder, corn starch and sugar.

• The Korean Journal of Mycology
• /
• v.18 no.1
• /
• pp.42-49
• /
• 1990

The cultural characteristics and some factors such as nutrient sources and supplements effecting on mycelial growth and density were investigated to study the possibility of an artificial cultivation of P. cocos. The optimum pH for P. cocos was 4.0-4.5. The optimal growth temperature ranged from $25^{\circ}C$ to $29^{\circ}C$. Myceial growth of P. cocos was better in SPD than PD media. Adding the nurient sources such as dextrose, yeast and potato infusion to pine extract media practically stimulated the mycelial growth and density of P. cocos comparing to pine extract media alone. When P. cocos was cultured on sawdust media added 3 different supplements composed of corn meal, rice bran and wheat bran, corn meal was the best and its percentage was 30 (w/w) for mycelial growth. On culturing in sawdust media added by varying the mixture ratio of them, the media mixed corn meal and wheat bran (3:1, w/w) supported more vigours for mycelial growth. In inoculation test to pine stem, the fungal growth was good in under or inside pine bark and xylem, but the sclerotium was not observed in the stem. Mycelial growth was also observed in central part of pine stem by cross section.

• Journal of Sensor Science and Technology
• /
• v.6 no.6
• /
• pp.451-457
• /
• 1997

The thick films of oxide semiconductors such as $WO_{3}$, $SnO_{2}$ and ZnO for the $NO_{2}$ detection of sub-ppm range have been prepared and their characteristics were investigated. It is showed that the optimum operating temperatures of the sensors are $300^{\circ}C$ and $220{\sim}260^{\circ}C$ for $WO_{3}$-based and $SnO_{2}$-based thick films, and ZnO-based thick films, respectively. Since the resistance of ZnO-based thick films are extremely high($>10^{6}{\Omega}$), the signal to noise ratio was comparatively low. In order to determine the selectivity, the films are exposed to the interfering gases such as ozone, ammonia, methane and the mixture of carbon monoxide and propane. $WO_{3}$-ZnO(3 wt.%) and $SnO_{2}-WO_{3}$(3 wt.%) thick film sensors show high sensitivity, good selectivity, excellent reproducibility and the linearity of $NO_{2}$ concentration versus sensor resistance. The preliminary results clearly demonstrated that the sensor can be successfully applied for the detection of $NO_{2}$ in sub-ppm range.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.12
• /
• pp.45-54
• /
• 2016

In this study, the construction method of new underground continuos impervious wall that the bentonite slurry keeps the stability of excavated trench and the mixture of cement and bentonite plays a role as a constituent of impervious wall in the trench. The merit of homogeneity of the method so called as a cement-bentonite slurry wall enables to accurately make an estimation of hydraulic conductivity of the walls compared with that by other general grouting methods and to verify their waterproof efficiency without difficulty at the design stage. The use of cement-bentonite slurry walls for the containment of groundwater flow has also proven a cost-effective impervious wall technology by employing the simple combination of construction equipments and easy and fast construction procedures. The engineering characteristics of cement-bentonite impervious wall obtained by carrying out the laboratory experiments under various conditions. This study reveals the effect of variation of constituent materials and their mixing methods (Water-Cement-Bentonite) on the engineering characteristics of a composition. Also, this study makes some recommendations on the optimum mixing ratio and mixing sequence for the best quality at the site. That is the most important factors to estimate the construction cost and design of the technique. The comparison is lastly made to evaluate the effect of ordinary Portland and blast furnace slag cement as a bonding material on the behavior of impervious walls.

• Korean Chemical Engineering Research
• /
• v.40 no.6
• /
• pp.687-693
• /
• 2002

The surface of polyethersulfone(PES) membrane treated by Ar, $NH_3$ plasma, and the effects were observed before and after the treatment. The membrane treated by Ar plasma was increased the O/C ratio and measured the hydrophilic group, and the one by $NH_3$ plasma was attached the amine group and the amino group. In addition, with the wettability of polyethersulfone membrane $CO_2$ and the polar functional groups of surface interacted increasingly. Thus by comparable increase of the soluble selectivity $CO_2$ to $N_2$ both the permeability and the selectivity of $CO_2$ was improved. The optimum condition for the $CO_2$ permeation and actual separation factor of the plasma treated membrane was as follows; the measurement of Ar-10 W-2 min plasma treatment was $13.19{\times}10^{-10}cm^3(STP)cm/cm^2{\cdot}s{\cdot}cmHg$ and 20.12, and the measurement of $NH_3$-50 W-2 min plasma treatment was $15.40{\times}10^{-10}cm^3(STP)cm/cm^2{\cdot}s{\cdot}cmHg$ and 20.06.

• Journal of the Korean Chemical Society
• /
• v.37 no.8
• /
• pp.765-772
• /
• 1993

Two-dimensional potassium tetratitanate ($K_2Ti_4O_9$) and three-dimensional potassium hexatitanate ($K_2Ti_6O_{13}$) fibers have been prepared by the combined method consisting of the flux melting (1150$^{\circ}C$)-slow cooling (cooling rate = 5$^{\circ}C$/h) process from the starting raw materials of $K_2CO_3$, and $TiO_2$ with the flux of $K_2MoO_4$. It was found that the fiber growth reaction is strongly dependent upon the mole ratio of flux (F) to raw material (R), which is 7 : 3 (F : R) as for the optimum growth condition. Relatively long fibers (average length ${\thickapprox}$ 4 mm) with a mixture of $K_2Ti_4O_9$ (major) and $K_2Ti_6O_{13}$ (minor) could be obtained when the reaction was carried out for the $K_2MoO_4-$K_2O{\cdot}4TiO_2$ (F : R = 7 : 3) system, but for the $K_2$MoO_4$-$K_2O{\cdot}6TiO_2$ (F : R = 7: 3) one, only the short fibers with ${\thickapprox}$ 2 mm long could be grown as the mixed phase of $K_2Ti_6O_{13}$ and $K_2Ti_4O_9$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.220-220
• /
• 2013

Surface-normal transmission electro-absorption modulator (EAM) are attractive for high-definition (HD) three-dimensional (3D) imaging application due to its features such as small system volume and simple epitaxial structure [1,2]. However, EAM in order to be used for HD 3D imaging system requires uniform modulation performance over large area. To achieve highly uniform modulation performance of EAM at the operating wavelength of 850 nm, it is extremely important to remove the GaAs substrate over large area since GaAs material has high absorption coefficient below 870 nm which corresponds to band-edge energy of GaAs (1.424 eV). In this study, we propose and experimentally demonstrate a transmission EAM in which highly selective backside etching methods which include lapping, dry etching and wet etching is carried out to remove the GaAs substrate for achieving highly uniform modulation performance. First, lapping process on GaAs substrate was carried out for different lapping speeds (5 rpm, 7 rpm, 10 rpm) and the thickness was measured over different areas of surface. For a lapping speed of 5 rpm, a highly uniform surface over a large area ($2{\times}1\;mm^2$) was obtained. Second, optimization of inductive coupled plasma-reactive ion etching (ICP-RIE) was carried out to achieve anisotropy and high etch rate. The dry etching carried out using a gas mixture of SiCl4 and Ar, each having a flow rate of 10 sccm and 40 sccm, respectively with an RF power of 50 W, ICP power of 400 W and chamber pressure of 2 mTorr was the optimum etching condition. Last, the rest of GaAs substrate was successfully removed by highly selective backside wet etching with pH adjusted solution of citric acid and hydrogen peroxide. Citric acid/hydrogen peroxide etching solution having a volume ratio of 5:1 was the best etching condition which provides not only high selectivity of 235:1 between GaAs and AlAs but also good etching profile [3]. The fabricated transmission EAM array have an amplitude modulation of more than 50% at the bias voltage of -9 V and maintains high uniformity of >90% over large area ($2{\times}1\;mm^2$). These results show that the fabricated transmission EAM with substrate removed is an excellent candidate to be used as an optical shutter for HD 3D imaging application.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.7
• /
• pp.31-37
• /
• 2011

Only a few studies have been conducted using reduced slag as recycled material. The reduced slag in electric furnace is produced as a by-product in making a steel and a few applications of the reduced slag as expensive additives and bonding materials or as the stabilized soils was reported. The purpose of this study is to present the feasibility of the reduced slag as recycled material, especially, in a field of civil engineering. In order to achieve the purpose experiments such as SEM and XRF analysis was conducted for the reduced slag in electric furnace. Based on the results various geotechnical experiments were conducted to know engineering properties of slag-soil mixtures. Weathered soils and clay are mixed with reduced slag for various ratios. As the ratio of reduced slag to weathered soil increases, the maximum dry unit weight of the mixture decreased with increasing optimum moisture content. The results indicates that there is no effect on a reduced slag by compaction efforts. The shear strengths of the weathered soil-slag mixtures are slightly higher or similar to those of weathered soils. The permeability of the weathered soil-slag mixtures is similar to that of silty or sandy soils. Therefore, it is possible to use the mixtures as embankment or backfill materials in the fields. The unconfined strength of the mixtures of reduced slag and clay is higher than that of clay and it tends to increase with the curing time. Therefore it can be used to improve the soft ground.

• Korean Chemical Engineering Research
• /
• v.44 no.4
• /
• pp.410-416
• /
• 2006

For highly efficient operation of a Bunsen process section in an iodine-sulfur thermochemical hydrogen production cycle using nuclear heat, the process characteristics of $H_2SO_4-HI-H_2-O-I_2$ mixture system for separating into two liquid phases ($H_2SO_4$-rich phase and $HI_x$-rich phase) and the distribution of $H_2O$ to each phase were investigated.The experiments for process variables were carried out in the temperature range, from 298 to 353 K, and in the $H_2SO_4/HI/H_2O/I_2$ molar ratio of 1/2/14~20/0.5~8.0. As the results, for the $SO_2-I_2-H_2O$ Bunsen reaction system, the ranges between the starting point and the saturation point for two liquid phases separation were determined by calculation. The best result for the minimization of impurities (HI and $I_2$ in $H_2SO_4$ phase and $H_2SO_4$ in $HI_x$ phase) in each phase was obtained in an optimum condition with the highest temperature of 353 K and the highest $I_2$ molar composition. In this condition, the $HI/H_2SO_4$ molar ratio in the $H_2SO_4$-rich phase and the $H_2SO_4/HI_x$ molar ratio in the $HI_x$-rich phase were 0.024 and 0.028, respectively. For the distribution of $H_2O$ to each phase, it is appeared that the affinity between $HI_x$ and $H_2O$ was more superior to that between $H_2SO_4$ and $H_2O$. The affinity between $HI_x$ and $H_2O$ was decreased with increasing temperature but increased with increasing $I_2$ molar composition.