• Journal of Ocean Engineering and Technology
• /
• v.13 no.3 s.33
• /
• pp.3-11
• /
• 1999

Optimum design of mooring dolphin is numerically investigated. Design optimization problem of moring dolphin is first formulated. Geometry and cross sections of piles are used as design variables. Design objective is the total weight of steel piles of mooring dolphin, and the constraints of stress, penetration depth, lower and upper bounds on design variables are imposed. Based on the design variable linking and fixing, several class of design variations are sought. For the numerical optimization, both PLBA(Pshenichny - Lim - Belegundu - Arora) program and DNCONF subroutine code in IMSL library are used. For a dolphin structure with 20 steel piles, vertical and inclined, optimum designs for different cases are successfully obtained, which can be applied for the mooring of a very large floating structure.

• ETRI Journal
• /
• v.18 no.1
• /
• pp.1-14
• /
• 1996

We have experimentally observed and theoretically analyzed the gain dependent optimum repetition rates of a hybrid-type active and passive mode locked laser pulses in an erbium-doped fiber laser of the figure-of-eight geometry by utilizing a nonlinear amplifier loop mirror (NALM) as a saturable absorber and a directional-coupler type electro-optic modulator as an active mode locker. Transform-limited mode-locked pulses of about 10 ps width were obtained at repetition rates which correspond to harmonics of the cavity fundamental frequency and depend on the optical amplifier gain in the NALM.

• Geomechanics and Engineering
• /
• v.8 no.4
• /
• pp.595-613
• /
• 2015

An experimental investigation into the uplift capacity of horizontal square plate anchors in sand with and without geogrid reinforcement is reported. The parameters investigated are the effect of the depth of the single layer of geogrid, vertical spacing of geogrid layers, number of geogrid layers, length of geogrid layers, the effects of embedment depth, and relative density of sand. A series of three dimensional finite element analyses model was established and confirmed to be effective in capturing the behaviour of plate anchor-reinforced sand by comparing its predictions with experimental results. The results showed that the geogrid reinforcement had a considerable effect on the uplift capacity of horizontal square plate anchors in sand. The improvement in uplift capacity was found to be strongly dependent on the embedment depth and relative density of sand. A satisfactory agreement between the experimental and numerical results on general trend of behaviour and optimum geometry of reinforcement placement is observed. Based on the model test results and the finite element analyses, optimum values of the geogrid parameters for maximum reinforcing effect are discussed and suggested.

• Journal of the Society of Naval Architects of Korea
• /
• v.40 no.4
• /
• pp.53-58
• /
• 2003

Design of the corrugated watertight bulkhead for a bulk carrier is principally determined by the permissible limit of Classification requirements. As the weight of upper and lower stool has considerable portion of the total weight of the transverse bulkhead, optimum design including the stool geometry and size will play an important role on economic shipbuilding. The purpose of this study is focused on the minimization of steel weight using the design variables, which are the shape and the size of the corrugation as well as the upper and lower stools. Discrete variables are used as design variables for the practical design. In this study, the evolution strategies (ES), which can highly improve the possibility of leaching the global minimum point, are selected as an optimization method. Usefulness of this study is verified by comparison with the proven type ship design. As objective function, total weight of the transverse bulkhead including the upper and lower stools is used.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.17 no.3
• /
• pp.5-17
• /
• 1980

A basic procedure to design marine propellers by a curved lifting line theory was shown. By adapting discrete singularity method, it became possible to take into account of skew, rake and the contraction of slip stream in the early stage of preliminary design procedure. It is also shown that lifting line theory based on the discrete singularity method converges to a common solution obtained by induction factor method with a relatively small number of discrete elements. Lifting the blade geometry more accurately on the basis of hydrodynamic principles. A number of numerical results from lifting line calculation are presented for the purpose of comparison with the previous method, and with these results two sample designs are carried out, which are wake-adapted optimum and wake-adapted non-optimum propellers.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.706-709
• /
• 1997

Extruders are the heart of the polymer processing industry. The single most important mechanical element of a screw extruder is the screw. The proper design of the geometriy of the extruder screw is of crucial importance to the proper functioning of the extruder. If material transport instabilities occur as a result of improper screw geometry, even the most sophisticated computerized control system cannot solve the problem. For this purpose, characteristics design on helix angle of the extruder screw. This paper presents strength of the screw flight, optimum helix angle versus dimensionless down channel pressure gradient, optimum helix angle versus the power law index in simultaneous optimization, volumetric efficiency versus helix angle at various number of flights and power consumption versus helix angle in the barrel of screw extruder.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.616-621
• /
• 2001

A numerical investigation was performed to determine the effect of airfoil on the optimum flap height using NACA 0021 Wells turbine. The five double flaps which have 0.5% chord height difference were selected. A Navier-Stokes code, FLUENT, was used to calculate the flow field of the Wells turbine. The basic feature of the Wells turbine is that even though the cyclic airflow produces oscillating axial forces on the airfoil blades, the tangential force on the rotor is always in the same direction. Geometry used to define the 3-D numerical grid is based upon that of an experimental test rig. This paper tries to analyze the optimum double flap of Wells turbine with the numerical analysis.

• KSTLE International Journal
• /
• v.3 no.1
• /
• pp.17-22
• /
• 2002

Roughing of tool steel in its hardened state represents a real challenge in the die and meld industry and process improvement depends on research of tool material, coating technique, and lubrication. However, roughing of hardened steels generates extreme heat and without coolant flooding, tool material cannot withstand the high temperature without choosing the right tools with proper coating. This research conducted milling tests using coated ball end mills to study effects of cutting conditions and geometric parameters of ball end mills on the machinability of hardened tool steel. KP4 steel and STD 11 heat treated steels were used in the dry cutting as the workpiece and TiAIN coated ball end mills with side relief angle of 12$^{\circ}$ was utilized in the cutting tests. Cutting forces, tool wear, and surface roughness were measured in the cutting tests. Results from the experiments showed that 85 m/min of cutting speed and 0.32 mm/rev of feed rate were optimum conditions for better surface finish during rough cutting and 0.26mm/rev with the same cutting speed are optimum conditions in the finish cutting.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.3
• /
• pp.32-39
• /
• 2004

A design procedure for a ship with minimum total resistance has been developed using a numerical optimization method called SQP(sequential quadratic programming) to search for different optimal hull forms. The frictional resistance has been estimated using the ITTC 1957 model-ship correlation line formula, and the wave resistance has been evaluated using a potential-flow panel method that is based on Rankine sources with nonlinear free surface boundary conditions. The geometry of a hull surface has been modified using B-spline surface patches, during the whole optimization process. The numerical analyses have been carried out for the modified Wilgey hull at three different speeds (Fn=0.25, 0.316, 0.408), and the calculation results were compared.

• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.2
• /
• pp.354-360
• /
• 2004

It is well known that pneumatic actuators convert fluid power into mechanical power with a low efficiency. The pneumatic rotary actuators are used in not only marine winches. but also hoists, agitators, and excavators. The efficiency of pneumatic rotary actuators depends on several factors, such as type of actuator. speed, supply pressure. size and geometry of the actuator. This paper presents an analytical and experimental study of the performance of pneumatic rotary actuators. We investigate all the major aspects of the air flow through a pneumatic rotary actuator and points out the main causes of the low efficiency of the actuator. Therefore the design parameters which can lead to optimum performance are obtained.