• Structural Engineering and Mechanics
• /
• 제38권4호
• /
• pp.385-403
• /
• 2011

Continuous deep girders which transmit the gravity load from the upper wall to the lower columns have frequently long end shear spans between the boundary of the upper wall and the face of the lower column. This paper presents the results of tests and analyses performed on three 1:2.5 scale specimens with long end shear spans, (the ratios of shear-span/total depth: 1.8 < a/h < 2.5): one designed by the conventional approach using the beam theory and two by the strut-and-tie approach. The conclusions are as follows: (1) the yielding strength of the continuous RC deep girders is controlled by the tensile yielding of the bottom longitudinal reinforcements, being much larger than the nominal strength predicted by using the section analysis of the girder section only or using the strut-and-tie model based on elastic-analysis stress distribution. (2) The ultimate strengths are 22% to 26% larger than the yielding strength. This additional strength derives from the strain hardening of yielded reinforcements and the shear resistance due to continuity with the adjacent span. (3) The pattern of shear force flow and failure mode in shear zone varies depending on the amount of vertical shear reinforcement. And (4) it is necessary to take into account the existence of the upper wall in the analysis and design of the deep continuous transfer girders that support the upper wall with a long end shear span.

• Steel and Composite Structures
• /
• 제49권2호
• /
• pp.215-230
• /
• 2023

Cable-girder anchorage joint is the critical part of cable-supported bridges. Tensile-plate anchorage (TPA) is one of the most commonly used types of cable-girder anchorage joints in steel girder cable-supported bridges. In recent years, it has been proposed by bridge designers to apply TPA to concrete girder cable-supported bridges to form composite cable-girder anchorage joint (CCGAJ). In this paper, the mechanical performance of CCGAJ under tensile force is studied through experimental and numerical analyses. Firstly, the effects of the external prestressing (EP) and the bearing plate (BP) on the mechanical performance of CCGAJ were investigated through three tests. Then, finite element model was established for parametrical study, and was verified by the experimental results. Then, the effects of shear connector forms, EP, BP, vertical rebar rate, and perforated rebar rate on the tensile capacity of CCGAJ were investigated through numerical analyses. The results show that the tensile capacity of CCGAJ depends on the first row of PR. The failure mode of CCGAJ using headed stud connectors is to form a shear failure surface at the end of the studs while the failure mode using PBLs is similar to the bending of a deep girder. Finally, based on the strut-and-tie model (STM), a calculation method for CCGAJ tensile capacity was proposed, which has a high accuracy and can be used to calculate the tensile capacity of CCGAJ.

• 대한토목학회논문집
• /
• 제33권1호
• /
• pp.115-130
• /
• 2013

철근콘크리트 파일캡의 설계 시 사용되고 있는 현행 설계기준의 단면법 및 스트럿-타이 모델 방법은 각각 B-영역으로 이루어진 철근콘크리트 구조부재의 거동과 2차원 응력교란영역을 갖는 철근콘크리트 구조부재의 거동에 기초한 것으로, 이를 응력교란영역(D-영역)을 갖고 3차원 거동이 지배적인 철근콘크리트 파일캡의 설계에 적용하는 것은 적절하지 않다. 이 연구에서는 3축 응력을 받는 콘크리트 스트럿 및 절점영역의 강도특성과 철근이 배치되지 않은 인장영역에서의 콘크리트 타이의 하중저항능력 등을 반영하여 철근콘크리트 파일캡을 합리적으로 설계할 수 있는 개선 3차원 스트럿-타이 모델을 제안하였다. 파괴실험이 수행된 78개 철근콘크리트 파일캡 시험체의 극한강도를 현행 설계기준의 단면법 및 스트럿-타이 모델 방법, 그리고 이 연구의 개선 3차원 스트럿-타이 모델을 이용하여 평가하였으며, 그 결과의 비교분석을 통해 스트럿-타이 모델 방법 적용 시의 3차원 거동 및 하중전달 메커니즘을 묘사하기 위한 적절한 구성요소의 필요성과 이 연구에서 제안한 개선 3차원 스트럿-타이 모델의 타당성을 검증하였다.

• Clinics in Shoulder and Elbow
• /
• 제21권4호
• /
• pp.220-226
• /
• 2018

Background: This study introduces a surgical technique with good clinical outcome useful in the treatment of osteoporotic displaced 3- or 4-part proximal humeral fractures. Methods: From May 2014 to February 2016, 16 patients with displaced 3- or 4-part proximal humeral fractures were treated by application of a locking plate with an endosteal strut allograft via a deltoid splitting approach with a minimum follow-up of 12 months. The allograft was inserted through a fractured gap of the greater tuberosity to support the humeral head and then fixed by a locking plate with meticulous soft tissue dissection to protect the axillary nerve. Surgical outcomes were evaluated by the American Shoulder and Elbow Surgeons (ASES) and visual analogue scale (VAS) scores, radiological imaging, and clinical examination. Fixation failure on radiographs was defined as a >$5^{\circ}$ loss of neck shaft angle (NSA) compared to that on an immediate postoperative radiograph. Avascular necrosis (AVN) of the humeral head was also evaluated. Results: In all cases, complete union was achieved. The ASES and VAS scores were improved to $85.4{\pm}2.1$ and $3.2{\pm}1.3$, respectively. Twelve patients (75.0%) had greater than a $5^{\circ}$ change in NSA; the average NSA change was $3.8^{\circ}$. Five patients (31.3%) had unsatisfactory ranges of motion exhibiting a <$100^{\circ}$ active forward flexion. No axillary nerve injuries or AVN were observed at the last follow-up. One patient was converted to reverse total arthroplasty due to severe pain and functional deficit. Conclusions: Minimally invasive fixation via a locking compression plate and an endosteal fibula strut allograft in Neer classification 3-or 4-part fractures with severe osteoporosis in elderly patients can achieve good clinical results.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.13-19
• /
• 2008

A Wire-woven Bulk Kagome (WBK) is the new truss type cellular metal fabricated by assembling the helical wires in six directions. The WBK seems to be promising with respect to morphology, fabrication cost, and raw materials. In this paper, first, the geometric and material properties are defined as the main design parameters of the WBK considering the fact that the failure of WBK is caused by buckling of truss elements. Taguchi approach was used as statistical design of experiment(DOE) technique for optimizing the design parameters in terms of maximizing the compressive strength. Normalized specific strength is constant regardless of slenderness ratio even if material properties changed, while it increases gradually as the strainhardening coefficient decreases. Compressive strength of WBK dominantly depends on the slenderness ratio rather than one of the wire diameter, the strut length. Specifically the failure of WBK under compression by elastic buckling of struts mainly depended on the slenderness ratio and elastic modulus. However the failure of WBK by plastic failed marginally depended on the slenderness ratio, yield stress, hardening and filler metal area.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권7호
• /
• pp.152-163
• /
• 2019

본 연구에서는 강섬유의 혼입, 매트릭스의 압축강도, 전단철근과 전단경간비가 UHPFRC 휨재에 미치는 영향에 대해 총 10개의 실험체에 대한 실험을 통해 검토하였다. 실험결과 2%의 부피비로 강섬유가 혼입된 경우 파괴 패턴을 전단파괴에서 휨파괴로 바꿀 정도로 높은 전단강도 증진효과를 보유하고 있는 것으로 나타났다. 또한 강섬유는 낮은 전단경간비에서 압축스트럿의 파괴를 지연시키는 효과를 가진 것으로 나타났다. 실험 결과 강섬유의 혼입과 전단경간비의 변화에 따라 균열각이 45도보다 낮은 것으로 나타났다. 실험 결과를 UHPC 설계권고안들과 비교해 본 결과 프랑스의 설계권고안은 보수적으로 평가하였고 한국의 설계권고안은 휨 강도에 대해 다소 과대평가하는 것으로 나타났다. 전단강도에 대해서는 두 설계권고안 모두 보수적으로 평가하는 것으로 나타났다.

• 대한토목학회논문집
• /
• 제35권1호
• /
• pp.101-110
• /
• 2015

최근 Hsu는 전단시험장치를 이용해 순수전단이 작용하는 9개 RC패널요소의 전단시험을 수행하였다(ACI 1997). 최신 트러스모델(수정압축장이론, 회전각연성트러스모델)은 평형조건과 적합조건 그리고 2축 상태에서 RC 막판넬의 연성 응력-변형률 관계를 이용하여 2중 루프의 시행착오방법으로 복잡한 비선형해석을 수행하고 있다. 본 연구는 스트럿과 타이의 파괴기준에 기반한 개선된 모어변형적합방법을 사용해 효율적인 알고리즘을 제안하였고, 이 알고리즘을 이용하여 Hsu가 실험한 전단이력 해석을 빠른 수렴속도로 개선한 것이다. 해석결과에 의하면 전단변형률 증폭상태의 전단변형에너지는 주압축 응력-변형률에 크게 지배받는 것으로 나타났다.

• Computers and Concrete
• /
• 제33권5호
• /
• pp.497-507
• /
• 2024

In squat reinforced concrete walls, the displacement capacity for lateral deformation is low and the ability to resist the axial load can quickly be lost, generating collapse. This work consists of testing two squat reinforced concrete walls. One of the specimens is built with conventional detailing of reinforced concrete walls, while the second specimen is built applying an alternative design, including stirrups along the diagonal of the wall to improve its ductility. This solution differs from the detailing of beams or coupling elements that suggest building elements equivalent to columns located diagonally in the element. The dimensions of both specimens correspond to a wall with a low aspect ratio (1:1), where the height and length of the specimen are 1.4 m, with a thickness of 120 mm. The alternative wall included stirrups placed diagonally covering approximately 25% of the diagonal strut of the wall with alternative detailing. The walls were tested under a constant axial load of 0.1f'cAg and a cyclic lateral displacement was applied in the upper part of the wall. The results indicate that the lateral strength is almost identical between both specimens. On the other hand, the lateral displacement capacity increased by 25% with the alternative detailing, but it was also able to maintain the 3 complete hysteretic cycles up to a drift of 2.5%, reaching longitudinal reinforcement fracture, while the base specimen only reached the first cycle of 2% with rapid degradation due to failure of the diagonal compression strut. The alternative design also allows 46% more energy dissipation than the conventional design. A model was used to capture the global response, correctly representing the observed behavior. A parametric study with the model, varying the reinforcement amount and aspect ratio, was performed, indicating that the effectiveness of the alternative detailing can double de drift capacity for the case with a low aspect ratio (1.1) and a large longitudinal steel amount (1% in the web, 5% in the boundary), which decreases with lower amounts of longitudinal reinforcement and with the increment of aspect ratio, indicating that the alternative detailing approach is reasonable for walls with an aspect ratio up to 2, especially if the amount of longitudinal reinforcement is high.

• Structural Engineering and Mechanics
• /
• 제75권6호
• /
• pp.675-684
• /
• 2020

An innovative retrofit method using pre-stressed steel strips and externally-bonded steel plates was presented in this paper. With the aim of exploring the seismic performance of the retrofitted RC interior joints, four 1/2-scale retrofitted joint specimens together with one control specimen were designed and subjected to constant axial compression and cyclic loading, with the main test parameters being the volume of steel strips and the existence of externally-bonded steel plates. The damage mechanism, force-displacement hysteretic response, force-displacement envelop curve, energy dissipation and displacement ductility ratio were analyzed to investigate the cyclic behavior of the retrofitted joints. The test results indicated that all the test specimens suffered a typical shear failure at the joint core, and the application of externally-bonded steel plates and that of pre-stressed steel strips could effectively increase the lateral capacity and deformability of the deficient RC interior joints, respectively. The best cyclic behavior could be found in the deficient RC interior joint retrofitted using both externally-bonded steel plates and pre-stressed steel strips due to the increased lateral capacity, displacement ductility and energy dissipation. Finally, based on the test results and the softened strut and tie model, a theoretical model for determining the shear capacity of the retrofitted specimens was proposed and validated.