• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.6
• /
• pp.55-64
• /
• 2007

This paper represents characteristics and design example of series loaded LCC type high frequency resonant DC-DC converter with variable parallel capacitor in the secondary side of inductive power transformer. In this converter, ZVS(zero voltage switching) technique is applied to reduce turn-off switching losses, and the applied converter used the PFM switching pattern to control output voltage. The operating characteristics of the proposed converter is analyzed using nomalized parameter such as switching frequency and load factor with varing the secondary parallel resonant capacitor. The results of analysis show the operating characteristics and design method of the proposed converter using characteristic values. And the proposed converter can be applied for the contactless power supply with linear transfer system such as dean room facilities of semiconductor and Flat Panel Display.

• Korean Chemical Engineering Research
• /
• v.51 no.5
• /
• pp.540-544
• /
• 2013

During start up and shut down of a proton exchange membrane fuel cells (PEMFC), the performance and lifetime of PEMFC were reduced. In this study, effect of startup and shutdown were investigated in dead-end type PEMFC using oxygen as a cathode gas with polarization curve, impedance spectroscopy (EIS), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Dummy load which eliminates residual hydrogen and oxygen during startup and shutdown operation should be applied to mitigated the degradation of PEMFC performance. At 50% relative humidity (RH) under the repetitive on/off cycling, the cell performance decayed faster than at 100% RH because of corrosion of the cathode carbon support. Water suppling into cell reduced the degradation rate of dead-end type PEMFC during start up and shut down cycling at 50% RH.

• Journal of the Ergonomics Society of Korea
• /
• v.26 no.2
• /
• pp.131-136
• /
• 2007

In this study, we developed an active ankle-foot orthosis(AAFO) which can control dorsi/ plantar flexion of the ankle joint to prevent foot drop and toe drag during walking. 3D gait analyses were performed on five healthy subjects under three different gait conditions: the normal gait without AFO, the SAFO gait with the conventional plastic AFO, and the AAFO gait with the developed AFO. As a result, the developed AAFO preeminently induced the normal gait compared to the SAFO. Additionally, AAFO prevented foot drop by proper plantarflexion during loading response and provided enough plantarflexion moment as a driving force to walk forward by sufficient push-off during pre-swing. AAFO also could prevent toe drag by proper dorsiflexion during swing phase. These results indicate that the developed AAFO may have more clinical benefits to treat foot drop and toe drag, compared to conventional AFOs, and also may be useful in patients with other orthotic devices.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.9
• /
• pp.805-811
• /
• 2016

This paper proposes an estimation algorithm of phase currents of inverter systems with the planar bus bars for brush-less DC (BLDC) motors. The planar bus bar can improve the characteristic of the EMC(Electro-Magnetic Compatibility). In these inverters, a single current sensor of the dc-link measures the sum of a smooth capacitor current and phase currents of brush-less DC motor. Thus, it is essential to extract phase currents from the measured single current to control BLDC motor. Therefore, in this paper, the phase current is estimated by analyzing equivalent circuits of the BLDCM in ON and OFF periods of switching elements. The usefulness of the proposed algorithm is verified through experimental results.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.2
• /
• pp.13-17
• /
• 2013

In lighting system where several large-area organic light-emitting diode (OLED) lighting panels are involved, panel aging may appear differently from each other, resulting in a falling-off in lighting quality. To achieve uniform light output across large-area OLED lighting panels, we have employed an optical feedback circuit. Light output from each OLED panel is monitored by the optical feedback circuit that consists of a photodiode, I-V converter, 10-bit analogdigital converter (ADC), and comparator. A photodiode generates current by detecting OLED light from one side of the glass substrate (i.e., edge emission). Namely, the target luminance from the emission area (bottom emission) of OLED panels is monitored by current generated from the photodiode mounted on a glass edge. To this end, we need to establish a mapping table between the ADC value and the luminance of bottom emission. The reference ADC value corresponds to the target luminance of OLED panels. If the ADC value is lower or higher than the reference one (i.e., when the luminance of OLED panel is lower or higher than its target luminance), a micro controller unit (MCU) adjusts the pulse width modulation (PWM) used for the control of the power supplied to OLED panels in such a way that the ADC value obtained from optical feedback is the same as the reference one. As such, the target luminance of each individual OLED panel is unchanged. With the optical feedback circuit included in the lighting system, we have observed only 2% difference in relative intensity of neighboring OLED panels.

• Culinary science and hospitality research
• /
• v.21 no.1
• /
• pp.235-249
• /
• 2015

This study was carried out to investigate the flavor changes of Lentinus edodes at different storage temperatures, time and natural additives using an electronic nose with six metal oxide sensors. To preserve good quality of modified atmosphere packaged Lentinus edodes, Four natural additives(Artemisia princeps, Artemisia capillaries, green tea, and activated charcoal) were used. The mushrooms were packaged in polyethylene films with each treatment and were stored at 5, 10 and $20^{\circ}C$. Increase in storage temperature and storage time decreased the ratio of resistance in the electronic nose as well as first principal component scores. In addition, indicating quality of mushroom reduced at high temperature and long storage time. The results of the electronic nose and the principal component analysis(PCA) in the mushrooms with Artemisia princeps and Artemisia capillaries that were stored at $5^{\circ}C$, and green tea and activated charcoal which were stored at $10^{\circ}C$ showed the good effects to maintain the freshness along with reducing off-flavor. However, there were no differences between control and treatment groups at $20^{\circ}C$.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.14 no.5
• /
• pp.423-430
• /
• 2009

Recently as the inactive response characteristics of the existing RCD used on low voltage power distribution system, so control of overload and electric short circuit faults, major causes of electrical fires, are not enough. Therefore, this paper confirms the unreliability of the existing RCD by electrical fault simulator and proposes a EFDPD by using semiconductor switching devices and a high precision current sensor (namely, reed switch) for the prevention of electrical disasters in low voltage power distribution system caused by overload or electric short circuit faults. The sensitive reed switch in the proposed EFDPD exactly detects the increased magnetic flux with the overload or the short current caused by a number of electrical faults, and the following, the self circuit breaker in EFDPD rapidly cuts off the system. The proposed EFDPD confirms the excellent characteristics in response velocity and accuracy in comparison with the conventional circuit breaker through various operation performance analysis. The proposed EFDPD can also prevent electrical disasters, like as electrical fires, which resulted from the malfunction and inactive response characteristics of the existing RCD.

• Journal of Pharmacopuncture
• /
• v.12 no.2
• /
• pp.21-29
• /
• 2009

Objective : This study was carried to identify the anatomical component of FTMM(Foot Taeyang Meridian Muscle) in human lower limb, and further to help the accurate application to real acupuncture. Methods : FTM at the surface of the lower limb was labelled with latex. And cadaver was stripped off to demonstrate muscles, nerves and the others and to display the internal structures of FTMM, being divided into outer, middle, and inner layer. Results : FTMM in human lower limb is composed of muscles, nerves, ligaments etc. The internal composition of the FTMM in human lower limb are as follows : 1) Muscle : Gluteus maximus. biceps femoris, semitendinosus, gastrocnemius, triceps calf, fibularis brevis tendon, superior peroneal retinacula, calcaneofibular ligament, inferior extensor retinaculum, abductor digiti minimi, sheath of flexor tendon at outer layer, biceps femoris, semimembranosus, plantaris, soleus, posterior tibialis, fibularis brevis, extensor digitorum brevis, flexor digiti minimi at middle layer, and for the last time semimembranosus, adductor magnus, plantaris, popliteus, posterior tibialis, flexor hallucis longus, dorsal calcaneocuboidal ligament at inner layer. 2) Nerve : Inferior cluneal nerve, posterior femoral cutaneous n., sural cutaneous n., proper plantar branch of lateral plantar n. at outer layer, sciatic nerve, common peroneal n., medial sural cutaneous n., tibial n. at middle layer, and for the last time tibial nerve, flexor hallucis longus branch of tibial n. at inner layer. Conclusions : This study proves comparative differences from already established studies from the viewpoint of constituent elements of FTMM in the lower limb, and also in the aspect of substantial assay method. We can guess that there are conceptional differences between terms (that is, nerves which control muscles of FTMM and those which pass near by FTMM) in human anatomy.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.30 no.2
• /
• pp.35-45
• /
• 2012

Need color separation process to appear number of minimum printing plate waterway maximum printing color at printing process. This time, printing plate is separated three primary colors of C(cyan), M(magenta), Y(yellow). Appear all colors of printing such three primary colors. But, three primary color ink appears 100% dark gray that is not clean as chroma is neared color to 0 because is not pure. As well as, the ink area rate that is whole by over print amount increase of three primary is expanded. As a result, influence in secondary printablity set-off growth by inaccurate color reproduction and ink dry badness, trapping efficiency decline etc.. Apply ink saving method that is replaced as K ink in consisted dark color constituent because three primary colors are over print each other adding one more K(black) plate by method to improve these problem. Therefore, can reduce extension of the total ink area rate, and help in correct color appearance control. As well as, eco-friendly printing process attains improving printablity at the same time curtailment of printing expense by reducing requirement of total ink. Usually, there are UCR(under color removal) and GCR(gray component replacement) to ink saving application method. But, the practical use limit is insufficient state to tribe of technological investigation or field application about these method in domestic printing field. Therefore, in this research, ink saving been bringing by one method of eco-friendly printing confirmed that is applicable in usual domestic printing environment. Also, searched result getting in printablity by ink saving application.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.3
• /
• pp.293-300
• /
• 2009

The rotorcraft-based unmanned aerial vehicle(UAV) capable of performing close-range surveillance and reconnaissance has been developed. Trade studies on mission feasibility led to the adoption of a coaxial rotorcraft with twin rotors counter-rotating in one axis and driven by electric motors. A commercial off-the-shelf flight control computer(FCC) and a radio frequency modem were adopted for autonomous navigation. In order to achieve an aerial view, commercial charge-coupled device camera was also integrated into the vehicle. The performance of the completed vehicle was proved with manual flight test, and mission capability was verified through waypoint navigation flight after being equipped with FCC. This paper treats the whole process of design and system integration for development of the coaxial rotorcraft UAV.