• The Journal of Korean Academy of Prosthodontics
• /
• v.59 no.4
• /
• pp.395-404
• /
• 2021

Purpose. The purpose of present study was to evaluate the effect of changing structural stability of wax disc on the fit of prosthesis when the milling proceeded in order. Materials and methods. Prepared maxillary left first molar was used to fabricate a Ni-Cr alloy reference model. This was scanned to design crown and then wax pattern was milled, invested and cast to fabricate prosthesis. The wax patterns located in a row centrally within a single wax disc were set into a total of five groups ranging from WM1 group that was first milled to WM5 group that was last milled and the number of each group was set as 10. Silicone replica technique was used to measure the marginal gap, axial internal gap, line angle internal gap, occlusal internal gap. Data was evaluated with one-way ANOVA with significance level set at α = .05 and then Tukey HSD test was conducted for post analysis. Results. Marginal gap measured in each group, it was 40.41 ± 2.15 ㎛ in WM1 group, 40.44 ± 2.23 ㎛ in WM2 group, 39.96 ± 2.25 ㎛ in WM3 group, 39.96 ± 2.48 ㎛ in WM4 group, and 40.57 ± 2.53 ㎛ in WM5 group. No significant difference was found between groups. The significant difference between the groups was also not found in the axial internal gap, line angle internal gap, and occlusal internal gap. Conclusion. Internal and marginal fit of single crown to the sequential order of milling processing in the single machinable wax disc did not seem to be affected by the sequence.

• Fire Science and Engineering
• /
• v.33 no.6
• /
• pp.165-172
• /
• 2019

This study presents the design and manufacture of a self-contained breathing apparatus SCBA wireless communication module with a multipoint simultaneous full-duplex communication system to enable communication between team members wearing the SCBA system. It is necessary for fire-fighters to wear the SCBA system during extinguishing and rescue work at the fire site. Evaluation of the team communication module confirmed the feasibility of communication over more than 500 m in the test condition based on the line of sight. By implementing the Ad-hoc function, it was confirmed that the communication distance could be extended to 128 m by automatic routing up to 3 hoc. The vertical distance inside the building for successful communication was up to the 5th floor in the open staircase and up to the 3rd floor in the partitioned staircase. Furthermore, the performance testing of the communication module assuming a fire situation, confirmed that five team members correctly recognized the standard abbreviation of fire and wireless communication without a separate PTT key operation. In addition, the flame resistance was verified by exposing the module to a flame at 950 ± 50 ℃ for 5 s and then immediately extinguishing the flame.

• The Journal of Korean Academy of Prosthodontics
• /
• v.54 no.3
• /
• pp.210-217
• /
• 2016

Purpose: The aim of this study was to evaluate the marginal and internal adaptation of monolithic zirconia restoration made without physical model by digital intraoral scanner. Materials and methods: A prospective clinical trial was performed on 11 restorations as a pilot study. The monolithic zirconia restorations were fabricated after digital intraoral impression taking by intraoral scanner (TRIOS, 3shape, Copenhagen, Denmark), computer-aided designing, and milling manufacturing process. Completed zirconia crowns were tried in the patients' mouth and a replica technique was used to acquire the crown-abutment replica. The absolute marginal discrepancy, marginal gap, and internal gap of axial, line angle, and occlusal part were measured after sectioning the replica in the mesiodistal and buccolingual direction. Statistical analysis was performed using Kruskal-Wallis and Mann-Whitney U test (${\alpha}=.05$). Results: From the adaptation analysis by replica, the statistically significant difference was not found between mesiodistal and buccolingual sections (P>.05), but there was significant difference among the measurement location (P<.01). The amount of absolute marginal discrepancy was larger than those of marginal gap and internal gap (P<.01). Conclusion: Within the limitations of this study, the adaptation accuracy of model-free monolithic zirconia restoration fabricated by intraoral scanner exhibited clinically acceptable result. However, the margin of zirconia crown showed tendency of overcontour and cautious clinical application and follow up is necessary.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.2 s.105
• /
• pp.89-94
• /
• 2006

A compact microstrip band-selective filter for ultra-wideband(UWB) radio system is proposed. The filter combines the traditional short-circuited stub highpass filter and coupled resonator band-stop filter on both sides of the mitered 50-ohm microstrip line. To realize the pseudo-highpass filtering characteristic over UWB frequency band(3.1 GHz to 10.6 GHz), a distributed highpass filter scheme is adopted. Three coupled resonators are utilized to obtain the band stop function at the desired frequency band. By meandering the coupled resonators, there is $29\;\%$ size reduction in footprint compared to the traditional band-stop filter using L-shaped resonators. The measured results show that the filter has a wide passband of $146.7\;\%$(2.1 GHz to 10.15 GHz) with low insertion loss and the stop band of $10.04\;\%$(5.2 GHz to 5.75 GHz) for 3-dB bandwidth. The measured group delay is less than 0.7 ns within the passband except the rejection band.

• Korea Journal of Hospital Management
• /
• v.14 no.4
• /
• pp.149-162
• /
• 2009

The purpose of this study is to design strategic hospital service based on each hospital's features. For this study, an assessment was conducted by 398 in-patents of one university hospital located in Seoul. The self-questionnaires, which were investigated from Oct. 15th to 29th in 2008, compared central reception desk with ward reception desk in satisfaction and re-use rate of patients. The major results of this study are as follow. First, according to each reception desk user, they have different satisfaction of it. As for the staff kindness, admission procedure, discharge procedure and manner of staff, those made patients be gratified as well. Second, when it comes to the intention of re-use, there were no significant features between them. Only convenience in admission and discharge procedure, however, was an attractive factor for the recommendation. Third, this study found out the reasons for higher re-use rate of central reception desk users. Regarding service, they were contented with the time for test and treatment. As for the hospital service, they would like to re-use this hospital because of convenient steps of paying interim fee and getting certificates. Forth, this study found out the reasons for higher re-use rate of ward reception desk users. As a point of hospital service view, they responded that respected privacy, hospital facility and general service were good for staying. As for the manner of staff, they mentioned nurses and staff in charge and whole staff members were kind. When it comes to the procedures of patient management, steps of discharge and paying interim fee were convenience. In conclusion, the results of this study suggest that providing a ward reception desk service can boost the satisfaction and re-use rate of in-patients. Furthermore, this strategic management method would be good for not only cutting the moving line but also efficient in-patient care system. These results can be used for the strategic hospital marketing field, as well. Even though this study has a limitation of the targeted populations which were only in a ward reception desk running hospital, it can say that having competitiveness in satisfaction of hospital service is good for promoting and differencing each hospital. Consequently, whole general management system would be adjusted first for differencing each hospital; however, this sort of additional factor should be concerned as well. I expect that this study would give meaningful data for designing strategic and differencing marketing method to lots of hospitals.

• Korean Journal of Remote Sensing
• /
• v.31 no.3
• /
• pp.215-226
• /
• 2015

Normally, aero photography using UAV uses about 430 MHz bandwidth radio frequency (RF) modem and navigates and remotely controls through the connection between UAV and ground control system. When using the exhausting method, it has communication range of 1-2 km with frequent cross line and since wireless communication sends information using radio wave as a carrier, it has 10 mW of signal strength limitation which gave restraints on life my distance communication. The purpose of research is to use communication technologies such as long-term evolution (LTE) of smart camera, Bluetooth, Wi-Fi and other communication modules and cameras that can transfer data to design and develop automatic shooting system that acquires images to UAV at the necessary locations. We conclude that the android based UAV filming and communication module system can not only film images with just one smart camera but also connects UAV system and ground control system together and also able to obtain real-time 3D location information and 3D position information using UAV system, GPS, a gyroscope, an accelerometer, and magnetic measuring sensor which will allow us to use real-time position of the UAV and correction work through aerial triangulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.11
• /
• pp.1217-1223
• /
• 2007

Advanced microwave absorbers for wide oblique incidence angles are required in many applications including wireless communication or vehicle identification in ITS(Intelligent Transport System) where 5.8 GHz DSRC(Dedicated Short Range Communication) system is applied. In this study, two-layered microwave absorber(with a laminate structure of dielectric/magnetic composites) has been designed for the achievement of low reflection coefficient over wide incidence angles at 5.8 GHz. Iron flake particles are used as the filler in the absorbing layer, and the magnetic composite sheet exhibits high magnetic loss due to ferromagnetic resonance in gigahertz frequencies. The surface layer of low dielectric constant containing small amount of carbon black is used as the impedance transformer. On the basis of transmission line theory, the reflection loss has been calculated for the two-layer structure with variation of incident angles for both TE(Transverse Electric) and TM(Transverse Magnetic) polarizations. At the optimum thickness of the composite layers, a low value of reflection loss(less than -10 dB) has been predicted for wide incidence angles up to $55^{\circ}$ which is in good agreement with the measured value determined by free-space measurement.

• Journal of the Korea Furniture Society
• /
• v.21 no.6
• /
• pp.515-524
• /
• 2010

In line with the government's policies for localization, furniture industry in the northern area in Gyeoggi-province at presence has been operated by several furniture industrial complexes in the region in small scale, but now it should be considered from overall view of furniture industry in order to develop more competitive industry. As a matter of this fact, Gyeonggi-province should be engaged in planning to make various industrial clusters of the furniture-related industry based on the northern area of province at structural as well as politic aspects, with the help of the analyzed status of the current furniture industry in region, in supporting them by the systemized policies and developing the overall program to foster furniture as an international-competitive industry. Therefore this study suggested 'furniture industry center' which will exclusively handle and maintain the network of each furniture company in the northern area of Gyeonggi-province and 'high-tech furniture industry complex' to keep pace with the globalization and to be competitive internationally and also 'common brand business' for the cooperation at technical phase. In order to realize and vitalize such suggestions, it is urgently necessary that the network consists of the furniture companies and the expert of the related department in local universities as the main body for furniture industry, of course Gyeonggi-province as well.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.4
• /
• pp.263-273
• /
• 2019

South Korea's OF cable is reaching its expected design life of 30 years, and as a result, the risk of failure is increasing. Therefore, it is necessary to diagnose the long-term operating OF cables through accurate diagnosis at the right time to prevent the failure. Currently, the KEPCO periodically conducts DGA. However, the gas found in DGA is caused by oil deterioration as well as insulation paper. Therefore, the analysis of the degree of polymerization and furan compounds which is an evaluation of insulation paper considered to be the life of OF cables is required. In addition, the results of the evaluation of deterioration of insulation paper need to be checked for correlation with the results of DGA. In this study, DGA carried out through GC, the degree of polymerization was analyzed using an automatic viscometer, and HPLC was used to detect the furan compounds. In addition, the obtained results were applied to the SVM technique, which was recently introduced to determine abnormalities in OF cable. And the results which were accurate and reliable were obtained.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2003.11a
• /
• pp.91-97
• /
• 2003

본 연구는 온라인 게임공간에서 게이머들이 어떻게 서로 다른 가치관과 행동 패턴을 드러내는지를 확인하고 이를 통해 온라인 게임세계의 문화를 이해하고 분석하기 위해 실시되었다. 전 세계에서 가장 많은 게이머들이 활동하고 있고, 한국과 일본에서 동시에 서비스되고 있는 온라인 게임인 〈리니지〉의 게이머들을 대상으로 온라인 설문조사를 실시하여 '라이프 스타일' 분석틀을 이용해서 이들이 게임공간에서 보이는 행동을 분류하였다. 글 결과 한국과 일본의 리니지 사용자들에게서 거의 유사한 세 가지 라이프스타일 패턴이 추출되었으며 한국과 일본에서 라이프스타일에 따른 행동 패턴이 일관적으로 나타나고 있음을 확인하였다. 도한 한국과 일본의 문화적 차이는 각 라이프스타일 프로파일의 극단성과 분포비율에 의해 반영되는 것으로 확인되었다. 일본의 탈사회적 게이머는 한국의 그것에 비해 더 극단적인 반면 전체 응답자 중에서 차지하는 비율이 적었고 게임 세계에서의 사회 경제적 위치도 낮았으며 한국에서는 비교적 적은 비율을 차지하던 싱글 플레이어 유형이 일본에서는 가장 많은 비중을 차지하는 것으로 나타났다. 또한 일본의 게이머들은 라이프스타일에 상관없이 대부분이 게임 공동체에 가입하는 반면 한국의 게이머들은 라이프스타일에 따라 공동체 참여율이 달랐지만 전체적인 참여율은 일본에 비해 높았다. 이러한 차이는 일본 게임세계에서 공동체 참여는 기본적인 의무인 반면 한국에서는 현실적인 이익과 직결된 활동임을 시사한다. 또한 게임몰입수준은 한국보다 일본의 리니지 게이머들이 높았다. 아시아 각 국에 한국에서 개발한 동일한 온라인 게임이 확산되어 있는 현황을 고려할 때, 온라인 게이머의 라이프스타일 척도는 한국과 일본뿐만 아니라 대만과 중국, 홍콩, 그리고 미국과 같은 리니지 게임이 서비스되는 모든 국가의 문화적 차이를 이해하고 과학적으로 분석할 수 있는 방법이 될 수 있을 것으로 기대된다. 의미를 되새기는 것으로 짧은 연구를 시작하겠다. 등은 활성 값이 70% 이상으로 퇴적물 독성이 상대적으로 낮았다. 이중나선 DNA 함량은 28.4 % - 49%로 대조군에 비해서 감소가 크다. 대부분의 정점이 대조군의 30% 내외로 정점 간의 차이는 크지는 않다. 그러나 다른 측정자료와 같이 정점 22에서 18%로 최소치를 나타내고, 정점 2, 12에서 20% 내외의 값을 보인다. 종합적으로 볼 때 오염물질의 유입이 크고, 광양제철 인근 정점 들이 모두 다른 정점에 비해서 낮아서, 퇴적물 독성이 높은 정점으로 조사되었다.hiwo의 광합성 능력은 낮은 농도들에서는 대조구와 유사하였으나, 5 $\mu\textrm{g}$/l의 높은 농도에서는 초기에 매우 낮은 광합성 능력을 보이다가 시간이 경과하면서 대조군보다 더 높은 경향을 나타냈다. 이러한 결과는 식물플랑크톤이 benso[a]pyrene의 낮은 농도에서 노출될 때는 이 물질을 탄소원으로 사용할 가능성이 있음을 시사한다. 본 연구의 결과들은 연안해역에 benso[a]pyrene과 같은 지속성 유기오염물질이 유입되었을 때 내정여부에 따라 식물플랑크톤 군집내 종 천이와 일차생산력에 크게 영향을 미칠 수 있음을 시사한다.TEX>5.2개)였으며, 등급별 회수율은 각각 GI(8.5%), GII(13.4%), GIII(43.9%), GIV(34.2%)로 나타났다.ments of that period left both in Japan and Korea. "Hyojedo" in Korea is supposed to have been influenced by the letter design. Asite- is also considered to have been "Japanese Letter Jobcheso." Therefore, the purpose of this study is to look into