• Journal of Aerospace System Engineering
• /
• v.14 no.2
• /
• pp.12-19
• /
• 2020

In Korea, the regulation is MOLIT Notice 2018-290, Guidance for Approval of Synthetic Flight Trainer as Flight Simulator and Flight Training Device. The FAA (Federal Aviation Administration) categorizes FSTD (Flight Simulation Training Device) into FFS (Full Flight Simulator) and FTD (Flight Training Device), according to its level. Additional categories for regulation are airplane and helicopter, depending on the type of aircraft. In this study, the objective tests for the handling quality of the FAA and Korean regulations were compared and analyzed. In QPS (Qualification Performance Standard), related test titles, flight conditions, and tolerance limits were analyzed for the handling quality. Based on this study, recommendations on amendments to the regulation was presented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.280-281
• /
• 2011

We fabricated the devices of TFT type with the amorphous chalcogenide channel. A single device consists of a Pt source and drain, a Ti glue layer and a GeSe chalcogenide channel layer on SiO2/Si substrate which worked as the gate. We confirmed the drain current with variations of gate bias and channel size. The I-V curves of the switching device are shown in Fig. 1. The channel of the device always contains amorphous state, but can be programmed into two states with different threshold voltages (Vth). In each state, the device shows a normal Ovonic switching behavior. Below Vth (OFF state), the current is low, but once the biasing voltage is greater than Vth (ON state), the current increases dramatically and the ON-OFF ratio is about 4 order. Based on the experiments, we contained the conclusion that the gate voltage can enhance the drain current, and the electric field by the drain voltage affects the amorphous-amorphous transition. The switching device always contains the amorphous state and never exhibits the Ohmic behavior of the crystalline state.

• Journal of Biomedical Engineering Research
• /
• v.40 no.1
• /
• pp.20-31
• /
• 2019

Medical device performance management is an activity that allows a device to be safely used and maintained even after it is put on the market. The purpose of this study is to provide procedures and criteria for selection of medical device items that should manage the safety and performance among medical devices in hospital. Investigate the performance management status of medical devices in hospitals and identify the performance management status by domestic and advanced regulatory agencies. Provides selection procedures and test methods for medical devices subject to performance management in hospitals based on medical device risk management and reliability. In addition, a case study on drug infusion pumps was conducted.

• Journal of Positioning, Navigation, and Timing
• /
• v.11 no.2
• /
• pp.119-126
• /
• 2022

This paper presents a method to reduce the vibration-induced noise effect of an inertial measurement device mounted on a self-driving vehicle. The inertial sensor used in the GNSS/INS integrated navigation system of a self-driving vehicle is fixed directly on the chassis of vehicle body so that its navigation output is affected by the vibration of the vehicle's engine, resulting in the degradation of the navigational performance. Therefore, these effects must be considered when mounting the inertial sensor. In order to solve this problem, this paper proposes to use an in-house manufactured vibration suppression device and analyzes its impact on reducing the vibration effect. Experimental test results in a static scenario show that the vibration-induced noise effect is more clearly observed in the lateral direction of the vehicle, but can be effectively suppressed by using the proposed vibration suppression device compared to the case without it. In addition, the dynamic positioning test scenario shows the position, speed, and posture errors are reduced to 74%, 67%, and 14% levels, respectively.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.9 no.2
• /
• pp.76-85
• /
• 2004

Biodevices composed of biomolecular layer have been developed in various fields such as medical diagnosis, pharmaceutical screening, electronic device, photonic device, environmental pollution detection device, and etc. The biomolecules such as protein, DNA and pigment, and cells have been used to construct the biodevices such as biomolecular diode, biostorage device, bioelectroluminescence device, protein chip, DNA chip, and cell chip. Substantial interest has focused upon thin film fabrication or the formation of biomaterials mono- or multi-layers on the solid surfaces to construct the biodevices. Based on the development of nanotechnology, nanoscale fabrication technology for biofilm has been emerged and applied to biodevices due to the various advantages such as high density immobilization and orientation control of immoblized biomolecules. This review described the nanoscale fabrication of biomolecular film and its application to bioelectronic devices and biochips.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.23 no.1
• /
• pp.27-36
• /
• 2005

Most of flated scanners and digital cameras in prepress process utilize CCD technology. Device calibration and characterization process is needed to transform the device dependent color to the device independent color. ICC profiles for digital input devices encapsulated information relating the device values to CIELAB or CIEXYZ coordinates. The main purposes of this article is to evaluate some of the transformation methods based on ICC proposed device profiles and to propose optimal color transformation method for accurate color imaging in printing process.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.11 no.4
• /
• pp.1841-1865
• /
• 2017

This paper proposes a new interference mitigation scheme for device-to-device (D2D) communications underlaying a cellular network. The object of the proposed scheme is to determine the number of data streams, a precoding matrix, and a decoding matrix of D2D networks so as to maximize the system capacity given the number of data streams of a cellular network while satisfying the constraint of the inter-system interference from D2D networks to the cellular network. Unlike existing interference mitigation schemes based on the interference alignment technique, the proposed scheme operates properly regardless of the number of data streams of a cellular network and moreover it does not require changing the precoding and decoding matrices of a cellular network. The simulation results demonstrate that the proposed scheme significantly increases the system capacity by mitigating the intra- and inter-system interference.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.957-960
• /
• 2008

The influences of silicon and MgO seed particle on the reconstruction characteristics of MgO protective layer were investigated to clarify the mechanism of reconstruction and exaggerated grain growth (EGG) in AC-PDP. The reconstruction and EGG are closely correlated with the driving force for nucleation and growth, interface energy and initial size distribution of MgO protective layer in plasma space during discharge in AC-PDP.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.13 no.2
• /
• pp.73-81
• /
• 2018

This paper describes a device platform which the blind can wear to keep path and to get surrounding information during their independent walking. Compared to the existing technologies, the proposed device could be used indoors and outdoors, and maps need not be provided in advance. It is composed of a glasses type device equipped with image sensors, and a portable device that analyzes sensor data for sighted guiding. RGB images and depth images are extracted to generate a walking map based on feature points. It also can cope with the risk of collision with bollard, color cone by applying vertical obstacle detection technology based on floor detection.

• Journal of KIISE:Computer Systems and Theory
• /
• v.32 no.3
• /
• pp.107-114
• /
• 2005

In this paper. we propose an architecture of IEEE1394 device driver for RTLinux. The device driver has two interfaces for applications running on the RTLinux kernel and Linux kernel. With the interfaces, the device driver simultaneously supports RT-Thread of RTLinux kernel and user level process of Linux kernel. This architecture could be a reference for designing other device driver on the dual kernel platform.