• 설비공학논문집
• /
• 제29권3호
• /
• pp.127-133
• /
• 2017

Performance analysis has been carried out on a high side scroll compressor that had a fixed scroll equipped with a circular oil groove on its thrust surface. Oil was supplied to the oil groove through an intermittent opening from a high pressure oil reservoir formed inside the orbiting scroll hub. Oil in the groove was then delivered to both suction and back pressure chambers by pressure differentials and viscous pumping action of the orbiting scroll base plate. Mathematical modeling of this oil groove system was incorporated into a main compressor performance simulation program for an optimum oil groove design. The study findings were as follows. Pressure in the oil groove can be controlled by changing its configuration and the oil passage area. With an enlarged oil passage, the pressure in the oil groove heightens due to an increased flow rate, but the pressure elevation in the back pressure chamber is small, resulting in reduced friction loss at the thrust surface between the two scrolls. On the other hand, by increasing the oil passage area, the oil content in the refrigerant flow increases. Considering all these factors, the energy efficiency ratio could be improved by about 3.6% under the ARI condition by an optimal oil groove design.

• 한국자동차공학회논문집
• /
• 제10권3호
• /
• pp.44-50
• /
• 2002

The connecting rod big-end bearing is one of the most heavily loaded components of the lubrication system of high-speed combustion engines. The supply oil flow has to pass to the main bearing and the rotating crankshaft before entering the connecting rod bearing. It is common knowledge that the centrifugal forces due to the crankshaft rotation influence the oil flow to connecting rod bearing through the oil supply bore, especially, when the oil supply system to the connecting rod bearing has a 180$^{\circ}$circumferential groove via a single drilling in the crankshaft. In this case, it should be confirmed that the groove oil pressure in the main bearing is sufficient to overcome these centrifugal forces. For the purpose, the dynamic oil pressure before entering oil supply bore to the connecting rod bearing was measured instead of averaged oil pressure in main gallery. Experimental test results show that the dynamic oil pressure in the oil groove was more useful than that of main gallery. And it was also found that the oil pressure fluctuation in the groove was sensitively affected by the reduction of the main bearing clearance.

• 통합자연과학논문집
• /
• 제14권3호
• /
• pp.95-98
• /
• 2021

By far, studies on the effect of oral administration of peppermint essential oil on blood pressure are not consistent, increasing or decreasing. And the effect of inhalation of peppermint essential oil on blood pressure was not reported. This study was designed to clarify the effect of peppermint essential oil inhalation on the blood pressure and autonomic nervous system. Blood pressure and heart rate variability (HRV) as an indicator of autonomic nervous system activity were measured. The systolic and diastolic blood pressure was not changed significantly by inhalation of peppermint essential oil. Standard deviation of normal to normal (SDNN), a parameter of total activity of autonomic nervous system also was not changed significantly. High frequency (HF) power level, an indicator of parasympathetic nervous system activity was not changed by peppermint. These results indicate that action mechanism of peppermint essential oil on blood pressure is different by the method of administration, oral or inhalation.

• Tribology and Lubricants
• /
• 제25권1호
• /
• pp.1-6
• /
• 2009

In this paper, the minimum oil film thickness and the maximum oil film pressure of engine bearings have been analyzed by using the elastohydrodynamic theory and Taguchi's design method as functions of the oil groove width, oil hole diameter, oil hole position, and oil supply pressure. The optimized design of the engine bearing f3r an automotive Diesel engine is very important for supporting a load-carrying capacity due to gas pres-sures from the engine combustion chamber and inertia forces of the piston. The optimized design data of engine bearings indicated that the optimized oil groove width and an oil diameter of a engine bearing are 8mm at the speed of 2,000 rpm for a given 4-cylinder Diesel engine. Thus, the oil groove oil groove and an oil hole for high performances of an engine bearing may be considered as major design parameters compared to other design factors, which are strongly related to the minimum oil film thickness and the maximum oil pressure distribution of the engine oil.

• 설비공학논문집
• /
• 제14권4호
• /
• pp.285-292
• /
• 2002

The vapor pressure and miscibility measurement apparatus was developed and used to obtain data for refrigerant/oil mixture. The vapor pressure and miscibility data for R-404A/32 ISO VG polyol ester (POE) oil mixture and R-404A/46 ISO VG polyol ester oil mixture are obtained over the temperature range from -20 to $60^{\circ}$ with at $10^{\circ}$ intervals and the oil concentration range from 0 to 70 wt%. Using the experimental data, an empirical model was developed to predict the temperature vapor pressure-concentration relations for R-404A/46 ISO VG polyol ester oil mixtures at equilibrium. In the R-404A/32 ISO VG polyol ester oil mixture, the average root-mean-square deviation between measured data and calculated results from the empirical model is 1.24% and in the R-404A/46 ISO VG polyol ester oil mixture, that is 1.37%. Miscibility for R-404A/32 ISO VG polyol ester oil mixture was observed all over the experimental conditions. Immiscibility for R-404A/So1est 46 oil mixture was observed at the low oil concentrations (20~30 wt%) over the high experimental temperature range (50~$60^{\circ}$).

• Tribology and Lubricants
• /
• 제26권4호
• /
• pp.240-245
• /
• 2010

This paper describes the influence on engine main bearing behavior of the oil film when the fuel is diluted on a diesel engine equipped with DPF system. Oil film pressure and the thickness is calculated in accordance to the fuel dilution. The calculation is based on the numerical analysis of the engine main bearing. As a result, the engine oil viscosity decreased as the fuel dilution increased. This led the increment of the maximum oil thickness pressure. Verification of the minimum oil film thickness settlement by the engine gas pressure and the fuel dilution was confirmed. Destruction possibility of the engine main bearing was foreseen when the engine speed was 2000 rpm with the fuel dilution 15% and the 5W40 engine oil.

• Ocean and Polar Research
• /
• 제37권1호
• /
• pp.73-80
• /
• 2015

In order to determine the appropriate volume of the a pressure compensator of deep seabed mining robots, this paper reports on an experimental test for oil volume change in an oil-filled box. At the design stage of underwater robots, it is crucial to determine the capacity of the hydraulic compensator which is replenished as much as the contracted oil volume of the robots. A pilot mining robot, MienRo was designed to work under 6,000 m in the deep sea. The hydraulic actuating oil and pressure compensating oil of MineRo may be exposed at a hydrostatic pressure environment of 600 bar. Although the oil can be assumed to be incompressible, its volume is actually changed under high pressure conditions due to air contained in the oil and oil contraction. To determine the capacity of the pressure compensator, the oil contraction rate should be verified through an experimental test using a hyperbaric chamber.

• 수산해양기술연구
• /
• 제28권2호
• /
• pp.184-190
• /
• 1992

The combustion characteristics, ignition delay, p-t, dp/dt, Q-t of diesel oil and fish oil blended diesel oils was investigated according to pressure and temperature in a constant volume combustion bomb. The results are as follows: 1) The influence of temperature and pressure on the ignition delay was almost constant in high temperature, regardless of the blending rates, and the ignition delay was shortest in the 60% blend. 2) The maximum pressure was high in order of with pure diesel oil, with the 20% blend and the 60% blend. 3) The rate of pressure rise was high in order of with pure diesel oil, with the 20% blend and the 60% blend. The rate of maximum pressure rise was significantly higher with pure diesel oil than with two blends. 4) The amount of accumulative heat release was large in order of with pure diesel oil, with the 20% blend and the 60% blend.

• 한국안전학회지
• /
• 제24권6호
• /
• pp.150-156
• /
• 2009

The oil pressure switch(OPS) for automobile is very important part to prevent an overheated engine and other problems by checking the operation of an engine oil system and displaying oil signs on a dashboard. OPS is the part that receives various stress caused by temperature, vibration, and corrosion in an engine room. Regarding existing steel OPS cases, there occur field errors due to the rust, and much concern comes from the low anticorrosion caused by CR6+ Free according to the restrictions of heavy metals. Therefore, the study analyzed average life, the failure rate, and reliability through the tests of performance according to temperature changes, mechanical strength, and run-test in order to confirm if the use of the oil pressure switch with Al of anti-corrosion can improves the reliability, instead of the existing steel products.

• 대한기계학회논문집
• /
• 제7권4호
• /
• pp.469-476
• /
• 1983

The effects of oil supply conditions on the static and dynamic properties of journal bearings supporting high speed rotors were investigated. The initially unknown hydrostatic pressure in oil pockets were determined by iteration with the aid of the equation of oil flow balance for given oil supply pressure and flow coefficients of oil inlet. For the calculation of dynamic characteristics, the dynamic changes of pressure in lubricating gaps and oil pockets were linearised with a perturbation method.