• Journal of Electrical Engineering and Technology
• /
• 제1권2호
• /
• pp.233-236
• /
• 2006

A 3-D numerical simulation of a buried-channel CCD (Charge Coupled Device) with a deep depletion has been performed to investigate its electrical and physical behaviors. Results are presented for a deep depletion CCD (EEV CCD12; JET-X CCD) fabricated on a high-resistivity $(1.5k\Omega-cm)\;65{\mu}m$ thick epi-layer, on a $550{\mu}m$ thick p+ substrate, which is optimized for X-ray detection. Accurate predictions of the Potential minimum and barrier height of a CCD Pixel as a function of mobile electrons are found to give good charge transfer. The depletion depth approximation as a function of gate and substrate bias voltage provided average errors of less than 6%, compared with the results estimated from X-ray detection efficiency measurements. The result obtained from the transient simulation of signal charge movement is also presented based on 3-Dimensional analysis.

• 한국전산유체공학회지
• /
• 제13권2호
• /
• pp.62-67
• /
• 2008

This study aims to investigate numerically the static stiffness characteristics of porous air bearing and to estimate appropriate permeability values of porous medium. In particular, a new roughness model is proposed and implemented into the commercial CFD code (FLUENT Ver. 6.2) by using C language based user subroutine. The predicted results are extensively compared with experimental data. The roughness model is also validated through comparison with the results from open literature. It is found that the predictions for static stiffness are in good agreement with experimental data. Therefore, the suggested model based on the roughness Reynolds number can be used in studying the stiffness characteristics of porous air bearing effectively. In addition, numerical simulations of various diameter size and conditions are conducted. According the results, it is expected that the static stiffness of porous air bearing has the non-linear characteristics.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1868-1873
• /
• 2011

In this paper, a theoretical formulation of a simplified wheel-set model for collision-induced derailments was evaluated by numerical simulations for the wheel-climb derailment and wheel-lift derailment types. The derailment types were classified into the wheel-climb derailment and the wheel-lift derailment according to the friction force direction of the wheel-flange. The wheel-climb derailment type was classified into Climb-up, Climb/Roll-over, and Roll-over-C, and wheel-lift derailment type was classified into Slip-up, Slip/Roll-over and Roll-over-L. To verify the theoretical equations derived for the wheel-climb derailment and the wheel-lift derailment, dynamic simulations using RecurDyn of Functionbay and Ls-Dyna of LSTC were performed and compared for some examples. The derailment predictions of the suggested theoretical formulation were in good agreement with those of the numerical simulations. The direction of the frictional force between the wheel-flange and the rail can be well predicted using the suggested derailment formulation at a initial derailment.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.181-185
• /
• 2001

Three-dimensional finite-element-based numerical model of turbulent flow, heat transfer, macroscopic solidification and inclusion trajectory in a continuos steel slab caster was developed Turbulence was incorporated using the Improved Low-Re turbulence model with positive preserving approach. The mushy region was modeled as the porous media with average effective viscosity. A series of simulations was carried out to investigate the effects of the casting speed, the slab size, the delivered superheat the immersion depth of the SEN on the transport phenomena. In the absence of any known experimental data related to velocity profiles, the numerical predictions of the solidified profile on a caster was compared with breakouts data and a good agreement was found.

• International Journal of Automotive Technology
• /
• 제6권6호
• /
• pp.563-570
• /
• 2005

A numerical study of high pressure and temperature droplet vaporization and combustion is conducted by formulating one dimensional evaporation model and single-step chemical reaction in the mixture of hydrocarbon fuel and air. The ambient pressure ranged from atmospheric conditions to the supercritical conditions. In order to account for the real gas effect on fluid p-v-T properties in high pressure conditions, the modified Soave-Redlich-Kwong state equation is used in the evaluation of thermophysical properties. Some computational results are compared with Sato's experimental data for the validation of calculations in case of vaporization. The comparison between predictions and experiments showed quite a good agreement. Droplet surface temperature increased with increasing pressure. Ignition time increased with increasing initial droplet diameter. Temporal or spatial distribution of mass fraction, mass diffusivity, Lewis number, thermal conductivity, and specific heat were presented.

• Korea-Australia Rheology Journal
• /
• 제12권2호
• /
• pp.125-133
• /
• 2000

The present work is aimed at performing injection molding filling simulation of fiber suspension in polymer based matrix. The numerical simulation incorporates the coupling effect between the flow field and the fiber orientation state together with in-plane velocity gradient effect with recently proposed closure approximations. Predicted orientation components are compared with available experimental data of a film-gated strip and a center-gated disk. Predictions with IBOF closure approximation show excellent behaviors with regard to accuracy and numerical efficiency. However, predicted results seem to have consistent errors in comparison with experimental data. Diffusivity term which accounts for fiber-fiber interaction might have to be modified.

• 한국전산유체공학회지
• /
• 제6권4호
• /
• pp.8-14
• /
• 2001

The phenomena of two-phase suspension flows appear widely in nature and industrial processes. Hence, it is of great importance to understand the mechanism of the gas-solid two-phase flows. In the present study, the numerical simulation has been approached by utilizing the Eulerian-Lagrangian methodology for describing the characteristics of the fluid and particulate phases in a vertical pipe and a 90°square-sectioned bend. The continuous phase(gas phase) is described by the Eulerian formulation and a κ-ε turbulence model is employed to find mean and turbulent properties of the gas phase. The particle properties(velocity and trajectory) are then described by a Lagrangian approach and computed using the mean velocity and turbulent fluctuating velocity of the gas phase. The predictions are compared with measurements by laser-Doppler velocimeter for the validation. As a result, the calculated results show good agreements.

• 한국전산유체공학회지
• /
• 제8권4호
• /
• pp.6-15
• /
• 2003

It is an aim of this study to perform extensive numerical study for analyzing the anisotropic turbulence effects on spatial and temporal behaviors of droplet for impinging sprays. The turbulence model of Durbin is used for comparisons with the k-ε model. The turbulence-induced dispersions of droplets are considered to describe the anisotropy of turbulence effectively and spray/wall interactions are simulated using the model of Lee and Ryou. Present study investigates the overall and the internal structures of impinging diesel sprays such as spray shapes, radius and height of wall sprays, Sauter mean diameter (SMD), local droplet velocity, and local gas velocity and compared the results with experimental data by two adopted turbulence models. When the anisotropy effect of turbulence is included, better predictions for both gas and droplet tangential velocities are obtained, compared to the k-ε model. It is concluded that anisotropic effect of turbulence should be considered for simulating impinging diesel sprays.

• 한국해안해양공학회지
• /
• 제7권4호
• /
• pp.355-367
• /
• 1995

정점에서의 조석(조위, 조류)은 전통적으로 조화분석 및 예보에 의해 추정되며 다른 방법은 조석수치모형에 의한 예보이다. 본 연구에서는 수치모형의 직접적인 출력으로서 조석을 추정하는 방법과 장기간(1개월)의 모형출력을 조화분석한 조위와 조류의 조화상수의 Data Table을 근거로 한 인천항 전역의 임의위치에서의 실시간적으로 조석을 신속하게 추정하는 방법을 제시하였다.

• Structural Monitoring and Maintenance
• /
• 제4권2호
• /
• pp.133-151
• /
• 2017

The paper describes the results of an experimental and numerical investigation into the structural and damage response of sandwich composites to low-velocity impact. Sandwich panels consisting of laminated composite skins with three different layups bonded to a PVC foam core were subjected to impact at various energy levels corresponding to barely visible impact damage (BVID) in the impacted skins. Damage assessment analyses were performed on the impacted panels to characterise the extent and the nature of the major failure mechanisms occurring in the skins. The data collected during the experimental analyses were finally used to assess the predictive capabilities of an FE tool recently developed by the authors for detailed simulation of impact damage in composite sandwich panels. Good agreement was observed between experimental results and model predictions in terms of structural response to impact, global extent of damage and typical features of individual damage mechanisms.