• 한국수정란이식학회지
• /
• 제14권2호
• /
• pp.121-129
• /
• 1999

The objective of this study was to produce calves by transfer of embryos derived from slaughter house(SHD) and ultrasound-guided ovum pick-up (OPU). At 60 hrs after injection of 400 mg FSH dissolved in 25% polyvinylpyrrolidone(PVP) by single dose, ultrasound-guided follicular oocyte aspiration was ferformed. Day-7 and day-8 blastocysts produced by in vitro maturation (IVM), fertilization (IVF) and culture(IVC) of the oocytes derived from SHD and OPU were nonsurgically transferred into recipients. The results obtained were as follows. The cleavage rate and the development rate to blastocysts were not significantly (P<0.05) different between the oocytes obtained by SHD (72.9% vs. 34.1%) and OPU (75.9% vs. 38.4%). The oocyte recovery rate from the number of follicles by ultrasound-guided aspiration were not significantly (P<0.05) different between Holstein (61.7%) and Hanwoo (60.1%), but the rate of oocytes useful for IVF was significantly (P<0.05) higher in Hanwoo (69.3%) than Holstein (59.6%). The cleavage rate and the development rate to blastocysts was not significantly (P<0.05) different between Holstein (74.9% vs. 39.2%) and recipients on day 8 of estrus cycle resulted in 13 pregnancies (34.2%). One of them was sacrificed during gestation period due to mastitis and another was aborted spontaneous. The resulting 14 calves were morphologically normal at birth. Seventy eight fresh OPU-IVF embryos were transferred into 21 recipients on day 8 of estrus cycles, resulting in pregnancy of 12 recipients (41.4%). Two of them were sacrificed during gestation period due to mastitis and the other two were aborted. Nevertheless, the 11 OPU-calves have been born normally.

• 한국화재소방학회논문지
• /
• 제30권5호
• /
• pp.87-92
• /
• 2016

국내에서는 고층 및 복합 건축물이 다수 시공되고 있는 상황에서 화재시 실효성 있는 연기대응 기술의 확립이 요구되고 있으며, 고층 건축물에서 제연설비에 대한 대안으로서 샌드위치 가압을 이용하는 연기제어 시스템의 적용이 확대되고 있다. 샌드위치 가압을 이용하는 연기제어 시스템은 연기확산 방지와 원할한 피난환경 제공을 위해서 적정 층간차압과 이를 위한 급배기 풍량의 설계에 관한 자료가 확보되어야 한다. 본 논문에서는 이러한 연구의 일환으로서 샌드위치 가압을 이용하는 연기제어 시스템이 설치된 실제 건축물에서 수행한 현장실험의 과정과 결과를 제시하였다. 실험에서 화재층의 배기풍량과 상하부층의 급기풍량으로 시간당 6회의 환기횟수를 적용하였으며, 시스템 가동으로 화재층인 12층과 그 상부층인 13층 사이에 약 260 Pa의 압력차가 형성되었다. 이러한 압력차 형성은 피난 및 방화구획에 상당한 영향을 미치므로 이에 대한 추가적인 연구가 필요하다.

• Nutrition Research and Practice
• /
• 제16권3호
• /
• pp.354-365
• /
• 2022

BACKGROUND/OBJECTIVES: Understanding the mechanism of chewing and swallowing food is important when creating a proper diet for older adults. This study investigated whether texture-modified model foods can reduce the difference in chewing and swallowing parameters between healthy community-living young and older adults. SUBJECTS/METHODS: In total, 35 older and 20 young adults (mean age: 75 and 25 years, respectively), matched for sex and number of teeth, were recruited and their unstimulated salivation and tongue pressure were measured. Simultaneous assessment of chewing and swallowing characteristics was conducted using surface electromyography and a videofluoroscopic swallowing study while the participants ingested 8 g of model food with one to four levels of hardness. RESULTS: The average tongue pressure and salivation among older adults were 61% and 49.7%, respectively, of the corresponding values observed in young adults. The older adult group used significantly (P < 0.05) increased muscle force with more chewing cycles (P < 0.05) than the young adult group, which was maintained even when consuming foods with the lowest hardness, although without chewing. However, the age effect on oral processing time existed only for the hardest foods. Swallowing difficulties among older adults were demonstrated by the significant increase in vallecula aggregation time. The total food intake duration was significantly (P < 0.05) longer in older adults than in young adults, regardless of food hardness. CONCLUSIONS: There were measurable differences in the process of chewing and swallowing food between young and older adults, which can be improved with food hardness control. Adjusting food hardness may help food intake in healthy older adults.

• Childhood Kidney Diseases
• /
• 제22권1호
• /
• pp.1-6
• /
• 2018

Rituximab (RTX) is a chimeric monoclonal antibody that inhibits CD20-mediated B-cell proliferation and differentiation. Several studies have examined its use in intractable nephrotic syndrome (NS) with some positive results. However, those studies examined such effects for a short-term period of 1 year, and some patients continued to relapse after a lapse in RTX treatment. Our use of RTX as a maintenance therapy (RTX injection when the CD19 cell count exceeded $100-200/{\mu}L$ before relapse) showed some noticeable efficacy. We used RTX in 19 patients with steroid-dependent NS (SDNS). In 12 patients treated with RTX maintenance therapy, only one relapse occurred. The mean treatment period was $23.4{\pm}12.7months$, and the mean number of RTX administrations was $3.9{\pm}1.6$. The relapse rates were decreased (from 2.68/year to 0.04/year), and the drug-free period also increased (from 22.5 days/year to 357.1 days/year) during maintenance therapy. The other seven patients were treated with one cycle of RTX or additional cycles in case of relapse (non-maintenance therapy). Relapse rates were significantly decreased after RTX treatment (from 1.76/year to 0.96/year, P=0.017). The relapse-free period was $15.55{\pm}7.38$ (range, 5.3-30.7) months. No severe side effects of RTX were found except for a hypersensitivity reaction such as fever and chills during its infusion. In conclusion, RTX is considered an effective and safe option to reduce the relapse rate by a single- or maintenance-interval therapy in SDNS.

• 대한기계학회논문집A
• /
• 제26권12호
• /
• pp.2581-2589
• /
• 2002

In this research, fretting tests were conducted in air to investigate the wear characteristics of fuel cladding materials with the fretting parameters such as normal load, slip amplitude, frequency and the number of cycles. A high frequency fretting wear tester was designed for this experiment by KAERI. After the experiments, the wear volume and the shape of wear contour were measured by the surface roughness tester. Tribologically transformed structures(TTS) were analysed by means of optical and scanning electron microscopes to identify the main wear mechanisms. The results of this study showed that the wear volume were increased with increasing slip amplitude, and the shape of wear contour was transformed V-type to W-type. Also, it was found that the critical slip amplitude was 168${\mu}{\textrm}{m}$. These phenomena mean that wear mechanism transformed partial slip to gross slip to accelerate wear volume. The wear depth increased with an increase of friction coefficient due to increase of normal load and frequency. The fretting wear mechanisms were believed that, after adhesion and surface plastic deformation occurred by relative sliding motion on the contact between two specimens, TTS creation was induced by surface strain hardening and wear debris were detached from the contact surface which were produced by the micro crack propagation and creation.

• 한국방사선학회논문지
• /
• 제8권7호
• /
• pp.377-382
• /
• 2014

방사선 임상 관련 분야에서 컴퓨터의 사용으로 인해 카세트 사용에서는 볼 수 없는 아티팩트가 만들어지고 있다. 고스팅 아티팩트는 평판형 박막 트랜지스터(Flat Panel Thin-Film Transistor) 배열 검출기를 사용할 때 발생될 수 있다. 특히 고선량의 방사선을 고대조도의 물질에 노출시킨 영상을 획득한 후, 바로 저선량의 조사가 이루어진 영상이 획득될 때 고스팅 아티팩트가 발생할 수 있다. 본 실험에서 고스팅 아티팩트가 육안 관찰시 3분에서 사라지는 것을 확인할 수 있었으며 정량적 분석으로는 대략 6분에서 없어지는 것을 확인할 수 있었다. 또한 이 아티팩트는 관전류보다는 관전압의 영향을 더 받는다는 사실과 노출에 의한 포획전하의 방출이 아닌 시간에 의해 포획전하가 소멸된다는 사실을 실험을 통해 검증할 수 있었다.

• 대한임베디드공학회논문지
• /
• 제15권5호
• /
• pp.215-225
• /
• 2020

Light detection and ranging (LiDAR) sensors detect the distance of the surrounding environment and objects. Conventional LiDAR sensors require a certain amount of a power because they detect objects by transmitting lasers at a regular interval depending on a constant resolution. The constant power consumption from operating multiple LiDAR sensors is detrimental to autonomous and electric vehicles using battery power. In this paper, we propose two algorithms that improve the inefficient power consumption during the constant operation of LiDAR sensors. LiDAR sensors with algorithms efficiently reduce the power consumption in two ways: (a) controlling the resolution to vary the laser transmission period (T_P) of a laser diode (LD) depending on the vehicle's speed and (b) reducing the static power consumption using a sleep mode depending on the surrounding environment. A proposed LiDAR sensor with a resolution control algorithm reduces the power consumption of the LD by 6.92% to 32.43% depending on the vehicle's speed, compared to the maximum number of laser transmissions (N_x·max). The sleep mode with a surrounding environment-sensing algorithm reduces the power consumption by 61.09%. The proposed LiDAR sensor has a risk factor for 4-cycles that does not detect objects in the sleep mode, but we consider it to be negligible because it immediately switches to an active mode when a change in surrounding conditions occurs. The proposed LiDAR sensor was tested on a commercial processor chip with the algorithm controlling the resolution according to the vehicle's speed and the surrounding environment.

• The Korean Journal of Ceramics
• /
• 제4권3호
• /
• pp.193-198
• /
• 1998

This paper presents the effects of an initial braking velocity, a braking pressure, and the number of braking stop on the tribological behaviors for the three different C-C composites using an inertia dynamic-friction tester. The C-C composites were prepared through the processes of several cycles of pitch impregnation/carbonization with different friction surface texture such as continuous 8-harness satin fabric (ADD-1), chopped fiber (ADD-2) and chopped fiber (ADD-3) having higher fiber volume fraction on friction than ADD-2 by about 10%. ADD-1 exhibited a higher fraction coefficient (0.41~0.33) than those of ADD-2 and ADD-3 (0.32~0.26) under the various initial braking velocities and braking pressures. The fraction coefficients decreased with increasing the initial velocity and the braking pressures. Wear rate by the thickness change after every 25 stop indicated that ADD-2 and ADD-3 having 1.7~2.7 $\mu\textrm{m}$/stop/pair were much lower than that of ADD-1 showing 5.0~6.5 $\mu\textrm{m}$/stop/pair. All specimens showed a little bit lower wear rate during the middle stage than the initial and latter stages among 100 braking stops. ADD-1 showed higher friction coefficient and wear rate due to the active pull-out of the fibers, evidenced by thicker were film and wear debrises.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.394.2-394.2
• /
• 2014

We fabricated highly transparent and flexible Ti doped In2O3 (TIO)/Ag nanowire(NW)/TIO (TAT) multilayer electrodes by linear facing target sputtering (LFTS) and brush-painting for used as flexible for anode organic solar cells(FOSCs). The characteristics of TAT transparent anode as a function of number of brush-painting cycles was also investigated. At optimized conditions we achieved highly flexible TAT multilayer electrodes with a low sheet resistance of $9.01{\Omega}/square$ and a high diffusive transmittance more than 80% in visible region as well as superior mechanical stability. The effective embedment of the Ag NW network between top and bottom TIO films led to a metallic conductivity, high transparency. Based on FE-SEM HRTEM, and XRD analysis, we can find that the Ag NW network was effectively embedded between top and bottom TIO layers due to good flexibility of Ag NW, the TAT multilayer showed superior flexibility than single TIO layer. Successful operation of FOSCs with high power conversion efficiency of 3.01% indicates that TAT hybrid electrode is a promising alternative to conventional ITO electrode for high performance FOSCs.

• 한국식품과학회지
• /
• 제41권1호
• /
• pp.77-81
• /
• 2009

Streptozotocin-유도 당뇨병 모델을 이용하여 흑삼의 혈당강하작용에 대한 효과를 연구하고 증포과정에 따른 ginsenoside의 조성 변화를 분석하였다. 증포별 ginsenoside의 정량분석 결과, 증포 횟수가 증가할수록 조사포닌의 총량과 대부분의 ginsenoside는 줄어든 반면 ginsenoside-$Rg_3$ 함량 및 PD/PT 비율은 증가하는 경향을 보였는데, 이러한 조성은 다른 인삼제품과는 차별성 있는 특징이다. 또한, streptozotocin-당뇨병 유발쥐를 이용한 모델실험에서 흑삼추출물의 투여는 고혈당 준위(300 mg/dL이상)를 정상 수준(102 mg/dL)으로 감소시켰으며, 혈당 수준의 감소는 glycolysis나 HMT shunt 및 지방산 합성에 관여하는 glucokinase, glucose-6-phosphate dehydrogenase, 6-phosphogluconate dehydrogenase, acetyl CoA carboxylase 등의 효소의 활성증대에 기인하는 것으로 판단되었다. 이러한 결과는 흑삼추출물의 유의적인 혈당강하 효과를 입증하며 이에 따라 신약이나 식이보조제의 항당뇨물질로서의 이용가능성을 시사한다.