Mesoscale modelling of concrete for static and dynamic response analysis -Part 2: numerical investigations
-
- Structural Engineering and Mechanics
- /
- 제37권2호
- /
- pp.215-231
- /
- 2011
As a brittle and heterogeneous material, concrete behaves differently under different stress conditions and its bulk strength is loading rate dependent. To a large extent, the varying behavioural properties of concrete can be explained by the mechanical failure processes at a mesoscopic level. The development of a computational mesoscale model in a general finite element environment, as presented in the preceding companion paper (Part 1), makes it possible to investigate into the underlying mechanisms governing the bulk-scale behaviour of concrete under a variety of loading conditions and to characterise the variation in quantitative terms. In this paper, we first present a series of parametric studies on the behaviour of concrete material under quasi-static compression and tension conditions. The loading-face friction effect, the possible influences of the non-homogeneity within the mortar and ITZ phases, and the effect of randomness of coarse aggregates are examined. The mesoscale model is then applied to analyze the dynamic behaviour of concrete under high rate loading conditions. The potential contribution of the mesoscopic heterogeneity towards the generally recognized rate enhancement of the material compressive strength is discussed.
An experimental and numerical research was conducted to gain a deeper insight on the structural behaviour of deep-beams with indirect supports and to assess the size effects in the ultimate state behaviour. The experimental campaign focused on the influence of the reinforcement tie distribution height on the compression check of the support region and on the benefits of using unbonded prestressing steel. Three reduced scale specimens were tested and used to validate the results obtained with a nonlinear finite element model. As a good agreement could be found between the numerical and the experimental results, the numerical model was then further used to perform simulations in large scale deep-beams, with dimensions similar to the ones to be adopted in a practical case. Two sources of size effects were identified from the simulation results. Both sources are related to the concrete quasi-brittle behaviour and are responsible for increasing failure brittleness with increasing structural size. While in the laboratory models failure occurred both in the experimental tests as well as in the numerical simulations after reinforcement yielding, the numerically analysed large scale models exhibited shear failures with reinforcement still operating in the elastic range.
Nowadays, steel fiber reinforced concretes (SFRCs) are widely used in practical applications. Significant experimental research has thus been carried out to determine the constitutive equations that represent the behavior of SFRCs under multiaxial loadings. However, numerical modelling of SFRCs via FEM has been challenging due to the complexities of the implementation of these constitutive equations. In this study, following the literature, a plasticity model is constructed for the behavior of SFRCs that involves the Willam-Warnke failure surface with the relevant evolution laws and a non-associated flow rule for determining the plastic deformations. For the precise (yet rapid) integration of the constitutive equations, an explicit substepping scheme consisting of yield intersection and drift correction algorithms is employed and thus implemented in ABAQUS via UMAT. The FEM model includes various material parameters that are determined from the experimental data. Three sets of parameters are used in the numerical simulations. While the first set is from the experiments that are conducted in this study on SFRC specimens with various contents of steel fibers, the other two sets are from the experiments reported in the literature. The response of SFRCs under multiaxial compression obtained from various numerical simulations are compared with the experimental data. The good agreement between numerical results and the experimental data indicates that not only the adopted plasticity model represents the behavior of SFRCs very well but also the implemented integration scheme can be employed in practical applications of SFRCs.
The paper presents experimental and numerical studies carried out on low-rise RC frames, typically found in developing countries. Shake table tests were conducted on 1:3 reduced scaled two-story RC frames that included a code conforming SMRF model and another non-compliant model. The later was similar to the code conforming model, except, it was prepared in concrete having strength 33% lower than the design specified, which is commonly found in the region. The models were tested on shake table, through multiple excitations, using acceleration time history of 1994 Northridge earthquake, which was linearly scaled for multi-levels excitations in order to study the structures' damage mechanism and measure the structural response. A representative numerical model was prepared in finite element based program SeismoStruct, simulating the observed local damage mechanisms (bar-slip and joint shear hinging), for seismic analysis of RC frames having weaker beam-column joints. A suite of spectrum compatible acceleration records was obtained from PEER for incremental dynamic analysis of considered RC frames. The seismic performance of considered RC frames was quantified in terms of seismic response parameters (seismic response modification, overstrength and displacement amplification factors), for critical comparison.
Oil refineries' Fluid Catalytic Cracking Units (FCCU) when in full operation may exhibit strong fluid dynamics caused by turbulent flow in the piping system that may induce vibrations in other mechanical and structural components of the Unity. This paper reports on the experimental-theoretical-computational program performed to get the vibration properties and the dynamic response amplitudes to find out alternative solutions to attenuate the excessive vibrations that were causing fatigue fractures in components of the bottle like reactor-regenerator of an FCC unit in operation in an existing oil refinery in Brazil. Solutions to the vibration problem were sought with the aid of a 3D finite element model calibrated with the results obtained from experimental measurements. A short description of the found solutions is given and their effectiveness are shown by means of numerical results. The solutions were guided by the concepts of structural stiffening and dynamic control performed by a nonlinear pendulum controller whose mechanical design was based on parameters determined by means of a parametric study carried out with 2D and 3D mathematical models of the coupled pendulum-structure system. The effectiveness of the proposed solutions is evaluated in terms of the fatigue life of critical welded connections.
선박이 부두에 안전하게 계류 및 예인하기 위해서는 관련 국제규정에 부합하는 설계를 해야 한다. 그러나 현재까지도 일부 소형 조선소 및 설계 회사에서는 그 내용을 정확히 숙지하지 못하고 있는 경우가 많다. 따라서 본 논문에서는 예인 및 계류설비에 관한 국제규정을 살펴보고, 최신 발효된 MEG4(Mooring equipment guideline 4) 기준에 만족하는 대표적인 계류 의장품인 볼라드(Bollard)와 쵸크(Chock)를 개발하고자 한다. 볼라드는 계류 밧줄을 선체에 고박하기 위한 의장품이며, 일반적으로 2개의 기둥으로, 대부분은 8자 매듭 형태로 사용하고 있다. 쵸크는 선외에서 선내로 들어오는 계류 밧줄의 방향을 전환하고, 밧줄의 손상을 방지하기 위하여 곡률을 갖는 주물방식으로 제작한다. 이 두 가지 계류 의장품은 선박의 선수와 선미, 중앙부 측면에서 많이 사용되고 있다. 최근 컨테이너선 및 LNG 운반선의 크기 증가로 인하여, 계류 밧줄 하중이 증가하고 있으며, 계류 의장품도 안전사용하중(Safe working load)이 변경되어야 한다. 본 연구에서는 유한요소해석 모델링을 통한 허용응력 평가법 결과를 정리하고, 분석하였다. 추가적으로 비선형 붕괴 거동 평가를 통하여, 안전사용하중 결정에 대한 검증을 수행하였고, 탄성영역 내 설계가 되었음을 확인하였다. 연구에서 제안하는 평가법 및 기준, 그리고 해석절차는 향후 유사 의장품 개발 시 참조가 가능하다.
지반에 인입된 파일에 대한 거동 해석은 지반의 비선형 거동 특성으로 인해 일반적으로 유한요소에 기반한 수치적인 방법을 주로 이용한다. 그러나 수치 해석은 파일-지반 모델링 및 연산에 많은 노력과 시간을 요구하므로 파일의 제원과 지반 물성치가 확정되지 않은 초기 설계 단계에서는 활용에 많은 한계를 갖는다. 반면, 지반을 선형화한 이론해석의 경우 수치 해석에 비해 모델이 단순하고 연산 시간이 매우 짧으므로, 해석의 신뢰성이 확보된다면 지반-지지구조의 거동 특성을 초기에 예측하는데 유용할 것이다. 본 연구에서 대상으로 하는 풍력발전기의 경우, 초기 설계 단계에서 풍력터빈의 고유진동수 예측을 위한 동적 거동 해석이 요구되며, 이 때 지반에 인입된 풍력터빈의 지지구조는 탄성경계조건으로 단순화하여 동적 거동 해석에 반영할 수 있다. 이를 위해, 본 논문에서는 풍력터빈 지지구조의 선단부 탄성 계수를 도출하고자 지반에 인입된 파일에 대한 파일-지반 연성해석을 수행하였다. 해석 시 지반의 변형은 탄성범위 이내에 있다고 단순화하여 지반에 인입된 파일을 탄성지지된 보로 모델링하였다. 탄성지지보 모델을 이용해 파일 선단에 수평 하중 또는 모멘트가 작용할 때 발생하는 파일의 횡변형을 구하고, 이로부터 영향계수를 도출하였다. 풍력터빈의 지지구조에 대한 해석 예로써, 모노파일과 석션파일에 대해 파일 선단의 영향계수를 구하고, 이를 문헌의 결과와 비교함으로써 해석 결과의 신뢰도를 검증하였다. 또한 이 두 파일의 깊이에 따른 변형 및 선단부의 스프링 상수를 비교하여 지지구조의 강성 측면에서 모노파일과 석션파일의 특성을 살펴보았다.
원자력발전소 부품중 안전과 관련된 구조물은 지진하중하에서 그 건전성을 유지하도록 설계되어야 한다. 그중 원자로내부구조물부품은 1차 내진분류에 속하는 것으로써 지진하중하에서의 건전성이 발전소 안전과 경제적인 관점에서 매우 중요하다. 지금까지 이러한 원자로내부구조물의 모델링에 대해서는 여러 사람들에 의해 연구되고 발표되었으나, 본 논문에서는 국내 발전소 중에서 Turn-jey base로 건설되어 이미 가동 중에 있는 영광 1&2호기의 원자로내부구조물에 대한 안전정지지진하의 거동을 Global Beam Model이라는 단순화된 모델을 이용하여 분석하였다. 이 모델의 설정을 위해서 주요부품들을 double pendulum의 보요소로 표현하였고, 이들 주요부품들의 특성해석을 범용유한 요소해석 코드인 ANSYS에 의해 구하여 이를 상부 및 하부에서 간격을 갖는 비선형 스프링으로 모델링하였다. 또한 이 비선형 스프링뿐만아니라 원자로용기와 원자로내부구조물부품들 사이의 유체동적현상을 묘사한 유체동력학적 coupling에 의해 pendulum의 보요소를 서로 연결시켜 모델링을 하였다. 가진자료인 안전정지하중은 영광 1&2호기의 원자로용기 지지부에 가해지는 응답스펙트럼을 시간이력함수로 바꾸었으며, 이 모델과 간진 하중을 가지고 비선형해석 code인 KWUSTOSS의 explicit Runge-Kutta-Gills algorithm을 이용하여 적분을 수행하므로써 안전정지지진하의 원자로 내부구조물에 대한 거동을 구하여 이 구조물의 주요부품에 대한 내진검증 및 구조물 내부에 있는 핵연료집합체의 내진 해석을 위한 입력자료를 확보할 수 있었다. 그리고 본 연구에서 사용된 Globa Beam Model의 간편성 및 효율성과 explicit Runge-Kutta-Gills algorithm에 대한 경제성을 확인할 수 있었다.파악되었 다. 그 외에도 '옥외공간이용 편리'(outdoor or recreation convenience)와 ' 이웃만족'(satisfaction with neighbors), 그리고 '주거환경 유형'(building type, building arrangement type)등도 유의한 인과적 관련을 보이므로써, 기존 문헌들이 제시하고 있는 것보다 훨씬 다양한 변수들이 다양한 경로를 통해 거주자 시각만족의 영향인자가 될 수 있는 가능성을 제시하고 있다. 가설 변수의 하나인 '길찾기의 난이 정도'(difficulty of way-finding)와 종 속변수간에 유의한 관련도가 나타나지 않은 이유로 길찾기 변수가 '시각만 족'보다는 거주자의 '안전만족'(safety)과 관련된 변수일 가능성도 아울러 지적되었다. 본 연구의 결과로부터, 주거 계획 및 설계분야 그리고 추후 관 련 연구 분야를 위한 여러 제안들이 제시되었다.에 관한 국가 규격은 국제 규격에서 저술한 바와 같이 특별히 규정된 것이 없고 VDE(Verband Deutscher Elektrotechniker: 서독전기기술 협회)와 SAE(Society of Automotive Engi- neers: 자동차 기술자 협회)에서 비교적 활발하고 Jaso(Japanese Automobile Standards Organization: 일본 자동차 표준협회)에서 많이 진행중에 있다. 본 고에서는 자동차의 전자제어에 따른 잡음 발생 요인과 전자파 간섭 관련 자동차 규격과 시험평가 방법에 대해 간단히 소개 하였다.저하에 저해요인으로서가 아니라, 인위적이던 자연적이던 간에 아들만 두면 단산하는 현행의 출산풍토하에서는 남아선호관이 오히려 출산력저하에 결정적으로 작용하고 있다고 하겠다. 태아의 성 판별을 통한 선택적 인공임신중절의 건수는 1990년 한해에
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70
The wall shear stress in the vicinity of end-to end anastomoses under steady flow conditions was measured using a flush-mounted hot-film anemometer(FMHFA) probe. The experimental measurements were in good agreement with numerical results except in flow with low Reynolds numbers. The wall shear stress increased proximal to the anastomosis in flow from the Penrose tubing (simulating an artery) to the PTFE: graft. In flow from the PTFE graft to the Penrose tubing, low wall shear stress was observed distal to the anastomosis. Abnormal distributions of wall shear stress in the vicinity of the anastomosis, resulting from the compliance mismatch between the graft and the host artery, might be an important factor of ANFH formation and the graft failure. The present study suggests a correlation between regions of the low wall shear stress and the development of anastomotic neointimal fibrous hyperplasia(ANPH) in end-to-end anastomoses. 30523 T00401030523 ^x Air pressure decay(APD) rate and ultrafiltration rate(UFR) tests were performed on new and saline rinsed dialyzers as well as those roused in patients several times. C-DAK 4000 (Cordis Dow) and CF IS-11 (Baxter Travenol) reused dialyzers obtained from the dialysis clinic were used in the present study. The new dialyzers exhibited a relatively flat APD, whereas saline rinsed and reused dialyzers showed considerable amount of decay. C-DAH dialyzers had a larger APD(11.70