• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.48 no.2
• /
• pp.34-45
• /
• 2016

Global warming and climate change have been caused by combustion of fossil fuels. The greenhouse gases contributed to the rise of temperature between $0.6^{\circ}C$ and $0.9^{\circ}C$ over the past century. Presently, fossil fuels account for about 88% of the commercial energy sources used. In developing countries, fossil fuels are a very attractive energy source because they are available and relatively inexpensive. The environmental problems with fossil fuels have been aggravating stress from already existing factors including acid deposition, urban air pollution, and climate change. In order to control greenhouse gas emissions, particularly CO2, fossil fuels must be replaced by eco-friendly fuels such as biomass. The use of renewable energy sources is becoming increasingly necessary. The biomass resources are the most common form of renewable energy. The conversion of biomass into energy can be achieved in a number of ways. The most common form of converted biomass is pellet fuels as biofuels made from compressed organic matter or biomass. Pellets from lignocellulosic biomass has compared to conventional fuels with a relatively low bulk and energy density and a low degree of homogeneity. Thermal pretreatment technology like torrefaction is applied to improve fuel efficiency of lignocellulosic biomass, i.e., less moisture and oxygen in the product, preferrable grinding properties, storage properties, etc.. During torrefacton, lignocelluosic biomass such as palm kernell shell (PKS) and empty fruit bunch (EFB) was roasted under an oxygen-depleted enviroment at temperature between 200 and $300^{\circ}C$. Low degree of thermal treatment led to the removal of moisture and low molecular volatile matters with low O/C and H/C elemental ratios. The mechanical characteristics of torrefied biomass have also been altered to a brittle and partly hydrophobic materials. Unfortunately, it was much harder to form pellets from torrefied PKS and EFB due to thermal degradation of lignin as a natural binder during torrefaction compared to non-torrefied ones. For easy pelletization of biomass with torrefaction, pellets from PKS and EFB were manufactured before torrefaction, and thereafter they were torrefied at different temperature. Even after torrefaction of pellets from PKS and EFB, their appearance was well preserved with better fuel efficiency than non-torrefied ones. The physical properties of the torrefied pellets largely depended on the torrefaction condition such as reaction time and reaction temperature. Temperature over $250^{\circ}C$ during torrefaction gave a significant impact on the fuel properties of the pellets. In particular, torrefied EFB pellets displayed much faster development of the fuel properties than did torrefied PKS pellets. During torrefaction, extensive carbonization with the increase of fixed carbons, the behavior of thermal degradation of torrefied biomass became significantly different according to the increase of torrefaction temperature. In conclusion, pelletization of PKS and EFB before torrefaction made it much easier to proceed with torrefaction of pellets from PKS and EFB, leading to excellent eco-friendly fuels.

• Journal of Acupuncture Research
• /
• v.19 no.3
• /
• pp.64-76
• /
• 2002

Objective : The purpose of this study is to investigate the mechanism and effect of moxibustion objectively and to be used as the quantitative data for developing the new thermal stimulating treatment by observing the combustion characteristics of commercial moxaes. Methods : We have selected two types(large-size moxa A(LMA), large-size moxa B(LMB)) among large moxaes used widely in the clinic. We examined combustion times, temperatures, temperature gradients in each period during a combustion of moxa. Results : 1. The ascending temperature gradient measured in the central point of non-contacted surface was fastest, the average ascending temperature gradient of both moxaes was $0.0384^{\circ}C/sec$, $0.0123^{\circ}C/sec$ respectively, 3.1 times faster in LMA. The maximum ascending temperature gradient was also about 2.9 times faster in LMA. The time required for the maximum ascending temperature gradient from ignition was 254sec, 411sec respectively. 2. The minimum descending temperature gradient in the retaining period was $-0.0250^{\circ}C/sec$, $-0.0090^{\circ}C/sec$ respectively and the average descending temperature gradient was $-0.0160^{\circ}C/sec$, $-0.0037^{\circ}C/sec$ respectively on the non-contact surface. 3. On the basis of the non-contact surface($A_I$), the time at which the effective stimulus period began to occur was about 264sec, 796sec respectively after an ignition, the time at which the maximum temperature began to occur was about 373sec, 1323sec respectively after an ignition, and the maximum temperature was $0.9^{\circ}C$ higher in LMA. The maximum ascending temperature gradient was also about 4.2 times faster in LMA. Conclusion : It was thought that not only the figure of moxicombustion device, but also the form and size of moxa had influence on the combustion characteristics deciding the performance of stimulus seriously.

• Korean Journal of Food Science and Technology
• /
• v.31 no.3
• /
• pp.720-726
• /
• 1999

High voltage pulsed electric fields (PEF) technology is a non-thermal technique which is applicable to extract useful components froms biological materials. This research suggested the possibility for extracting carotenoid pigments from Phaffia rhodozyma by PEF treatments. The yeast cell suspensions were treated with high voltage pulses in a recycled PEF treatment chamber which consists a pair of thin plates of stainless steel adhering to a small chamber with approximately $1{\sim}4\;mm$ gap. A 2.5 log reduction in survivability and more than 98% of electropermeabilization of the yeast cells could be achieved by PEF treatment for $300\;{\mu}s$ with an electric field of 30 kV/cm and pulse duration of $1\;{\mu}s$. When the yeast cell suspended in 0.01% NaCl solution were treated with PEF under various conditions, carotenoid pigments were not extracted. However, the PEF treatment of the yeast cell suspensions in 0.01% $CaCl_2$ solution, have positive effects on the extraction of carotenoid pigments ($27.3\;{\mu}g/g$ of dried yeast).

• Korean Journal of Food Science and Technology
• /
• v.35 no.6
• /
• pp.1237-1243
• /
• 2003

As a newly emerging pasteurization method for improving the shelf-life of powdered ginseng, the corona discharge generated at high voltage conditions was examined for its effects on microbial pasteurization, physicochemical characterization, and sensory evaluation. The pasteurizing effects of corona discharge on total bacteria, yeast, molds, and coliforms increased with increasing voltage. However, corona discharge treatment of 5 kv/cm did not show significant effects of pasteurization on the yeast, molds, and coliforms. Treatment with 20 kv/cm reduced about 95% of the total bacteria $(6.14{\pm}0.04{\rightarrow}\;4.59{\pm}0.04$) and coliforms ($2.43{\pm}0.05{\rightarrow}\;1.00{\pm}0.05$) and 99% of the yeast and molds ($4.65{\pm}0.06{\rightarrow}\;2.73{\pm}0.06$). The proximate analysis, minerals, free sugars, crude saponin, and colors of the control ginseng and the ginseng treated with 20 kv/cm were not significantly different at p<0.05. Corona discharge of up to 20 kv/cm did not affect the proximate analysis, minerals, free sugars, crude saponin, and colors of the powdered ginseng. Sensory evaluation scores on color, flavor, taste and overall acceptability between the control ginseng and ginseng treated with 20 kv/cm corona discharge were not significantly different at p<0.05 level. Consequently, corona discharge treatment is thought to be a good alternative pasteurization method for improving the shelf-life of powdered ginseng due to its effective pasteurization, maintenance of nutrients and good sensory characteristics.

• Korean Journal of Materials Research
• /
• v.30 no.6
• /
• pp.301-307
• /
• 2020

In this study, factors considered to be causes of promotion of densification of sintered pellets identified during phase change are reviewed. As a result, conclusions shown below are obtained for each factor. In order for MA powder to soften, a temperature of 1,000 K or higher is required. In order to confirm the temporary increase in density throughout the sintered pellet, the temperature rise due to heat during phase change was found not to have a significant effect. While examining the thermal expansion using the compressed powder, which stopped densification at a temperature below the MA powder itself, and the phase change temperature, no shrinkage phenomenon contributing to the promotion of densification is observed. The two types of powder made of Ti-silicide through heat treatment are densified only in the high temperature region of 1,000 K or more; it can be estimated that this is the effect of fine grain superplasticity. In the densification of the amorphous powder, the dependence of sintering pressure and the rate of temperature increase are shown. It is thought that the specific densification behavior identified during the phase change of the Ti-37.5 mol.%Si composition MA powder reviewed in this study is the result of the acceleration of the powder deformation by the phase change from non-equilibrium phase to equilibrium phase.

• Fire Science and Engineering
• /
• v.26 no.5
• /
• pp.13-20
• /
• 2012

Many fire-fighters suffer from the burn injuries, and the severe burns are the most catastrophic injury a person can survive, resulting in pain, emotional stress, and tremendous economic costs. It is important to understand the physiology of burns for prevention from skin burns and a successful treatment of a burn patient. But a few researches have been presented because the complex physical phenomena of our inside body like non-linearity characteristics of human skin make them difficult. Thus in this study, thermal analyses of biological tissues exposed to a flash fire causing severe tissue damage were studied by using a finite difference method based on the Pennes bio-heat equation. The several previous models for skin thermo-physical properties were summarized, and the calculated values with those models of tissue injury were compared with the results obtained by the previous experiment for low heat flux conditions. The skin models with good agreement could be found. Also, the skin burn injury prediction results with the best model for high heat flux conditions by flash flame were suggested.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.622-622
• /
• 2013

Piezoelectric energy harvesting (PEH) device refers to a power device for acquiring mechanical energy from the environment surrounding us which would otherwise be wasted and for converting it into usable electrical energy. While much work has been done on developing ZnO nanogenerator (NG) with nanowire arrays, there are some issues of not only scaling up its output power but also optimizing structure for operating feasibly in various conditions. Efficiency of NG is highly dependent on fixed orientation. But in many cases, it is not easy to predict where the pressure and vibration may come from. Furthermore, the direction of the applied mechanical stress is usually non-stationary and can be random in various practical applications. Therefore an omnidirectional PEH is needed.In this work, we investigate an omnidirectional PEH device consisting ZnO nanowires. We deposited spiral patterned ZnO seed layer on Kapton film. We deposited thin Cr layer on the ZnO seed layer using DC-sputter to form a passivation layer to retard un-expected growth of ZnO nanowires. We grew ZnO nanowires along the spiral arms using hydrothermal method. ZnO nanowires have been selectively grown from the ZnO sidewall without Cr layer and have the average length of$5{\mu}m$ and the average diameter of 40nm. We reduced the defect in the as-grown ZnO nanowires by O2 plasma using asher and by thermal treatment using RTA. Consequently, each nanowire has different directions to each other. This isotropic design can lead to the omnidirectional power generation. The morphology of NG is characterized with FESEM. Maximum output power of the device is measured by using a picoammeter and a nanovoltmeter.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.6
• /
• pp.1806-1808
• /
• 2014

We report the successful preparation of gold nanoparticles (Au NPs) using a novel electroreduction process, which is simple, fast, and environmentally friendly (toxic chemicals such as strong reducing agents are not required). Our process allows for the mass production of Au NPs and adequate particle size control. The Au NPs prepared show high biocompatibility and are non-toxic to healthy human cells. By applying radio-frequency (RF) ablation, we monitored the electro-hyperthermia effect of the Au NPs at different RFs. The Au NPs exhibit a fast increase in temperature to $55^{\circ}C$ within 5 min during the application of an RF of 13 MHz. This temperature rise is sufficient to promote apoptosis through thermal stress. Our work suggests that the selective Au NP-mediated electro-hyperthermia therapy for tumor cells under an RF of 13 MHz has great potential as a clinical treatment for specific tumor ablation.

• Journal of Korean Society of Water and Wastewater
• /
• v.34 no.3
• /
• pp.183-190
• /
• 2020

Although membrane bio-reactor (MBR) has been widely applied for wastewater treatment plants, the membrane fouling problems are still considered as an obstacle to overcome. Thus, many studies and commercial developments on mitigating membrane fouling in MBR have been carried out. Recently, high voltage impulse (HVI) has gained attention for a possible alternative technique for desalting, non-thermal sterilization, bromate-free disinfection and mitigation of membrane fouling. In this study, it was verified if the HVI could be used for mitigation of membrane fouling, particularly the internal pore fouling in MBR. The HVI was applied to the fouled membrane under different conditions of electric fields (E) and contact time (t) of HVI in order to investigate how much of internal pore fouling was reduced. The internal pore fouling resistance (R_f) after HVI induction was reduced as both E and t increased. For example, R_f decreased by 19% when the applied E was 5 kV/cm and t was 80 min. However, the R_f decreased by 71% as the E increased to 15 kV/cm under the same contact time. The correlation between E and t that needed for 20% of R_f reduction was modeled based on kinetics. The model equation, E^1.54t = 1.2 × 10³ was obtained by the membrane filtration data that were obtained with and without HVI induction. The equation states the products of En and t is always constant, which means that the required contact time can be reduced in accordance with the increase of E.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.159-160
• /
• 2012

지난 30년 동안 플래시 메모리의 주류 역할을 하였던 부유 게이트 플래시 메모리는 40 nm 기술 노드 이하에서 셀간 간섭, 터널 산화막의 누설전류 등에 의한 오동작으로 기술적 한계를 맞게 되었다. 또한 기존의 비휘발성 메모리는 동작 시 높은 전압을 요구하므로 전력소비 측면에서도 취약한 단점이 있다. 그러나 이러한 문제점들을 기존의 Si기반의 소자기술이 아닌 새로운 재료나 공정을 통해서 해결하려는 연구가 최근 활발하게 진행되고 있다. 특히, 플래시 메모리의 중요한 구성요소의 하나인 터널 산화막은 메모리 소자의 크기가 줄어듦에 따라서 SiO2단층 구조로서는 7 nm 이하에서 stress induced leakage current (SILC), 직접 터널링 전류의 증가와 같은 많은 문제점들이 발생한다. 한편, 기존의 부유 게이트 타입의 메모리를 대신할 것으로 기대되는 전하 포획형 메모리는 쓰기/지우기 속도를 향상시킬 수 있으며 소자의 축소화에도 셀간 간섭이 일어나지 않으므로 부유 게이트 플래시 메모리를 대체할 수 있는 기술로 주목받고 있다. 특히, TBM (tunnel barrier engineered memory) 소자는 유전율이 큰 절연막을 적층하여 전계에 대한 터널 산화막의 민감도를 증가시키고, 적층된 물리적 두께의 증가에 의해 메모리의 데이터 유지 특성을 크게 개선시킬 수 있는 기술로 관심이 증가하고 있다. 본 연구에서는 Si3N4/Ta2O5를 적층시킨 staggered구조의 tunnel barrier를 제안하였고, Si기판 위에 tunnel layer로 Si3N4를 Low Pressure Chemical Vapor Deposition (LPCVD) 방법과 Ta2O5를 RF Sputtering 방법으로 각각 3/3 nm 증착한 후 e-beam evaporation을 이용하여 게이트 전극으로 Al을 150 nm 증착하여 MIS- capacitor구조의 메모리 소자를 제작하여 동작 특성을 평가하였다. 또한, Si3N4/Ta2O5 staggered tunnel barrier 형성 후의 후속 열처리에 따른 전기적 특성의 개선효과를 확인하였다.