Journal of Advanced Marine Engineering and Technology
/
제30권1호
/
pp.157-168
/
2006
Recently, interest in using Al alloys in ship construction instead of fiber-reinforced plastic (FRP) has increased because of the advantages of A) alloy ships over FRP ships, including high speed, increased load capacity. and ease of recycling. This paper investigated the mechanical and electrochemical properties of Al alloys in a slow strain rate test under various potential conditions. These results will provide reference data for ship design by determining the optimum protection potential regarding hydrogen embrittlement and stress corrosion cracking. In general, Al and Al alloys do not corrode on formation of a film that has resistance to corrosion in neutral solutions. In seawater, however, $Cl^-$ ions lead to the formation and destruction of a Passive film. In a potentiostatic experiment. the current density after 1200 sec in the Potential range of $-0.68\~-1.5\;V$ was low. This low current density indicates the protection potential range. Elongation at an applied potential of 0 V was high in this SSRT. However, corrosion protection under these conditions is impossible because the mechanical properties are worse owing to decreased strength resulting from the active dissolution reaction in parallel parts of the specimen. A film composed of $CaCO_3\;and\;Mg(OH)_2$ confers corrosion resistance. However, at potentials below -1.6 V forms non-uniform electrodeposition coating, since there is too little time to form a coating. Therefore, we concluded that the mechanical properties are poor because the effect of hydrogen gas generation exceeds that of electrodeposition. Comparison of the maximum tensile strength, elongation, and time to fracture indicated that the optimum protection potential range was from -1.45 to -0.9 V (SSCE).
우리나라는 세계 7위의 온실가스 배출국가로서 국제적으로 배출량 규제가 강화됨에 따라 국가 온실가스 감축 목표를 상향하였고 이로 인해 산업계를 포함한 사회 전반적인 탄소 감축의 노력이 절실한 상황이다. 기후변화 완화 또는 적응 계획의 중요 이행 수단으로 연안과 해양생태계를 자연기반 해법(nature-based solutions, NbS)으로 활용 가능하게 되면서 최근 블루카본(blue carbon) 생태계가 주목받고 있다. 블루카본은 대기 중 이산화탄소가 광합성작용을 통해 맹그로브, 염습지 및 해초류와 같은 연안 생태계나 해조류와 미세조류와 같은 해양생태계에 의해 바이오매스로 흡수된 뒤 퇴적되어 장기간 저장되는 탄소를 의미한다. 현재 기후변화에 관한 정부 간 협의체(IPCC, Intergovernmental Panel on Climate Change)에서 현재 공식적으로 인정하고 있는 블루카본 생태계는 맹그로브, 염습지, 해초지 3가지뿐이다. 하지만, 최근 해조류, 미세조류, 산호초, 비식생 갯벌 등 다양한 새로운 블루카본 흡수원들이 가진 높은 이산화탄소 격리 및 저장 능력에 대해 새로운 연구 결과들이 지속적으로 학계에 보고되고 있어, 이들 신규 블루카본 후보군들의 온실가스 흡수량 산정에 관련된 과학적 입증을 통해 IPCC 국제 인증의 가능성이 점차 높아지고 있다. 본 총설에서 동해안이 보유하고 있는 블루카본 흡수원인 해조류, 해초지 및 비식생 갯벌의 현황과 잠재적 가치에 대해 논하고자 한다. 본 논문을 통해 동해는 해조류 자원을 NbS로 활용하는 것이 가장 효과적인 것으로 확인되었다. 또한, 동해안이 보유한 신규 블루카본 흡수원이 이른 시일 내에 IPCC 국제 인증을 받을 수 있도록 연구개발의 방향성과 활용방안을 제안하고자 한다.
본 연구에서는 배합강도 24MPa로 설계된 25-24-18 규격의 콘크리트 배합에 불소-실리카 복합형 균열저감제(FS)를 시멘트 중량을 기준으로 0.5% 간격으로 2.0%까지 혼입하고, 유동성상 및 경화성상 등의 기초물성을 평가하였다. 기초물성 결과로부터 콘크리트의 수축균열 및 투기성 평가를 위한 FS의 적정 첨가율로서 0.5%를 도출하였으며, 무첨가 콘크리트와 수축균열 및 투기성 평가를 위한 모의부재 시험을 실시하였다, 수축균열에서 FS를 0.5% 첨가한 콘크리트의 균열개수는 50%, 균열길이 및 균열면적은 각각 69.7%, 74.4% 감소되었다. 콘크리트의 투기성을 측정한 결과, FS를 첨가한 콘크리트가 투수계수는 67%, 침투깊이는 약 40% 감소하였다. 따라서 FS 첨가에 의해 콘크리트의 기초물성 저해 없이 콘크리트의 수축균열의 저감과 투기성이 향상되는 효과를 확인할 수 있었다.
본 연구에서는 이론화학 또는 분자모델링이라 불리는 계산화학을 기존에 연구된 촉매반응 실험결과를 해석하는 데 접목시켜 보았다. 온실효과의 주범인 이산화탄소를 에폭사이드와 반응을 통해 고정화하고 카보네이트를 생성하는 반응을 선택하였는데 이 반응은 활성화 에너지(55~59 kcal/mol)가 높아 촉매의 사용이 불가피하다. 많은 기존 연구들 중에 ZIF-90/ionic liquid immobilized ZIF-90 (IL-ZIF-90), polystyrene-supported quaternized ammonium salt, KI/KI-glycine, dimethylethanolamine (DMEA)를 촉매로 사용한 경우에 대해 반응의 각 단계를 계산하여 반응의 경로를 예측하고 단계별로 구한 에너지를 바탕으로 에너지도를 구성함으로써 실험결과를 열역학적으로 해석하였다. ZIF-90/IL-ZIF-90과 KI/KI-glycine의 경우는 실험적으로 후자들이 상대적으로 높은 수율을 얻었는데 계산 결과 활성화에너지가 낮아진 이유가 아니라 전자들의 경우 반응 중간체가 높은 에너지를 가져 반응물로 되돌아가는 역반응에 의해 정반응의 진행이 방해를 받은 것으로 밝혀졌다. DMEA를 촉매로 사용하였을 경우는 활성화 에너지를 ~42 kcal/mol로 낮춰줌으로써 금속이나 할로겐염 없이도 촉매의 활성이 잘 일어남을 증명하였다. 폴리스티렌(polystyrene)으로 지지된 quaternized 암모늄염 촉매의 경우 클러스터 가정을 사용하여 계산을 진행하였으며 암모늄염의 -NH기와 에폭사이드의 O 원자 사이의 상호작용의 가능성을 확인할 수 있는 반응경로를 제시하였다.
근권토양으로부터 고추역병균을 포함한 다양한 식물 병원성 곰팡이에 대하여 항균활성이 강한 세균을 분리하였다. 이 세균은 16S rRNA gene서열 분석 결과 Lysobacter enzymogens로 동정되었고 LE429로 명명 하였다. LE429는 chitinase, ${\beta}-1$, 3-glucanase, protease, gelatinase, lipase 및 항생물질과 같은 다양한 이차대사산물을 분비하였다. 항생물질은 diaon HP-20 및 sephadex LH-20 컬럼크로마토그래피 및 HPLC로 정제하여, GC-EI 및 GC-CI분석을 통하여 phenylacetic acid로 동정되었다. Field 실험에서 LE429의 고추 병해 억제 효과를 조사하기 위해 LE429배양액(CB), Neem oil 용액 (NO), LE429배양액과 Neem oil 용액을 섞은 혼합액(CB+NO), 그리고 대조구로서 물(CON)을 각각 고추에 처리하였다. 고추의 수량구성요소는 일반적으로 CB 처리구가 가장 높았고, CB+NO, CON 그리고 NO 순서로 나타났다. CB 처리구에서 병원성 곰팡이는 강하게 억제 되었지만, 몇몇 해충이 발견되었다. NO 처리구에서는 해충은 발견 되지 않았지만, 병원성 곰팡이가 발견 되었다. 하지만, CB+NO 처리구에서 병원성 곰팡이 및 해충이 전혀 발견 되지 않았다. 결론적으로, 2차 대 사산물을 생산하는 LE429와 Neem oil의 혼합액은 고추에 발생하는 병원성 곰팡이와 해충에 대한 좋은 생물학적 방제제가 될 수 있다고 사료된다.
상추의 기내 callus 배양으로부터 ACAT (Acyl-CoA: Cholesterol acyltransferase) 억제 활성물질로 알려진 phytol 의 생산가능성이 연구되었다. Callus는 0.5mg.L$^{-1}$ NAA가 첨가된 MS 배지에 4주간 치상된 자엽 절편체로부터 유도되었으며, 다양한 수준의 chlorophyll을 함유하고 있었다. Phytol이 chlorophyll분자를 구성하는 물질로 알려져 있음에 도 불구하고, phytol의 추출량은 녹색의 자엽에서 보다 callus 에서 높게 나타났다. GC 분석결과, phytol의 추출량은 callus의 chlorophyll 함량과 비례하지 않는 것으로 나타났으며, callus의 chlorophyll 함량수준은 callus의 형성능과 관련이 있는 것으로 사료되었다. 본 연구의 결과는 phytol의 기내생산에 있어서 상추의 callus 배양의 잠재성을 제시한다 하겠다.
Kim, Seoyoung;Kim, Junhyung;Choi, Jaehoon;Jeong, Woonhyeok;Kwon, Sunyoung
Archives of Plastic Surgery
/
제44권6호
/
pp.482-489
/
2017
Background Polydeoxyribonucleotide (PDRN) is known to have anti-inflammatory and angiogenic effects and to accelerate wound healing. The aim of this study was to investigate whether PDRN could improve peripheral tissue oxygenation and angiogenesis in diabetic foot ulcers. Methods This was a prospective randomized controlled clinical trial. Twenty patients with a non-healing diabetic foot ulcer were randomly distributed into a control group (n=10) and a PDRN group (n=10). Initial surgical debridement and secondary surgical procedures such as a split-thickness skin graft, primary closure, or local flap were performed. Between the initial surgical debridement and secondary surgical procedures, 0.9% normal saline (3 mL) or PDRN was injected for 2 weeks by the intramuscular (1 ampule, 3 mL, 5.625 mg, 5 days per week) and perilesional routes (1 ampule, 3 mL, 5.625 mg, 2 days per week). Transcutaneous oxygen tension ($TcPO_2$) was evaluated using the Periflux System 5000 with $TcPO_2/CO_2$ unit 5040 before the injections and on days 1, 3, 7, 14, and 28 after the start of the injections. A pathologic review (hematoxylin and eosin stain) of the debrided specimens was conducted by a pathologist, and vessel density (average number of vessels per visual field) was calculated. Results Compared with the control group, the PDRN-treated group showed improvements in peripheral tissue oxygenation on day 7 (P<0.01), day 14 (P<0.001), and day 28 (P<0.001). The pathologic review of the specimens from the PDRN group showed increased angiogenesis and improved inflammation compared with the control group. No statistically significant difference was found between the control group and the PDRN group in terms of vessel density (P=0.094). Complete healing was achieved in every patient. Conclusions In this study, PDRN improved peripheral tissue oxygenation. Moreover, PDRN is thought to be effective in improving inflammation and angiogenesis in diabetic foot ulcers.
Arcella, V.;Colaianna, P.;Brinati, G.;Gordano, A.;Clarizia, G.;Tocci, E.;Drioli, E.
한국막학회:학술대회논문집
/
한국막학회 1999년도 The 7th Summer Workshop of the Membrane Society of Korea
/
pp.39-42
/
1999
Perfluoropolymers represent the ultimate resistance to hostile chemical environments and high service temperature, attributed to the presence of fluorine in the polymer backbone, i.e. to the high bond energy of C-F and C-C bonds of fluorocarbons. Copolymers of Tetrafluoroethylene (TEE) and 2, 2, 4Trifluoro-5Trifluorometoxy- 1, 3Dioxole (TTD), commercially known as HYFLON AD, are amorphous perfluoropolymers with glass transition temperature (Tg)higher than room temperature, showing a thermal decomposition temperature exceeding 40$0^{\circ}C$. These polymer systems are highly soluble in fluorinated solvents, with low solution viscosities. This property allows the preparation of self-supported and composite membranes with desired membrane thickness. Symmetric and asymmetric perfluoropolymer membranes, made with HYFLON AD, have been prepared and evaluated. Porous and not porous symmetric membranes have been obtained by solvent evaporation with various processing conditions. Asymmetric membranes have been prepared by th wet phase inversion method. Measure of contact angle to distilled water have been carried out. Figure 1 compares experimental results with those of other commercial membranes. Contact angles of about 120$^{\circ}$for our amorphous perfluoropolymer membranes demonstrate that they posses a high hydrophobic character. Measure of contact angles to hexandecane have been also carried out to evaluate the organophobic character. Rsults are reported in Figure 2. The observed strong organophobicity leads to excellent fouling resistance and inertness. Porous membranes with pore size between 30 and 80 nanometers have shown no permeation to water at pressures as high as 10 bars. However high permeation to gases, such as O2, N2 and CO2, and no selectivities were observed. Considering the porous structure of the membrane, this behavior was expected. In consideration of the above properties, possible useful uses in th field of gas- liquid separations are envisaged for these membranes. A particularly promising application is in the field of membrane contactors, equipments in which membranes are used to improve mass transfer coefficients in respect to traditional extraction and absorption processes. Gas permeation properties have been evaluated for asymmetric membranes and composite symmetric ones. Experimental permselectivity values, obtained at different pressure differences, to various single gases are reported in Tab. 1, 2 and 3. Experimental data have been compared with literature data obtained with membranes made with different amorphous perfluoropolymer systems, such as copolymers of Perfluoro2, 2dimethyl dioxole (PDD) and Tetrafluorethylene, commercialized by the Du Pont Company with the trade name of Teflon AF. An interesting linear relationship between permeability and the glass transition temperature of the polymer constituting the membrane has been observed. Results are descussed in terms of polymer chain structure, which affects the presence of voids at molecular scale and their size distribution. Molecular Dyanmics studies are in progress in order to support the understanding of these results. A modified Theodoru- Suter method provided by the Amorphous Cell module of InsightII/Discover was used to determine the chain packing. A completely amorphous polymer box of about 3.5 nm was considered. Last but not least the use of amorphous perfluoropolymer membranes appears to be ideal when separation processes have to be performed in hostile environments, i.e. high temperatures and aggressive non-aqueous media, such as chemicals and solvents. In these cases Hyflon AD membranes can exploit the outstanding resistance of perfluoropolymers.
정치망 어선에 사용하는 더블 캡스턴 드럼의 용접공정은, 순간적으로 집중투입되는 고온열원에 의해 상당 열응력과 열변형 거동이 시간의 경과에 따라 비정상적으로 발생한다. 유한요소법으로 이것들의 거동을 해석한 후 다음과 같은 결론을 얻었다. 1) 용접 초기에는 용접열원 위치에서 54∼48MPa의 상당 열응력을 나타내고, 캡스턴 드럼의 내부로 진행될수록 42∼18Mpa 정도의 열응력 분포를 보이며, 열응력 구배는 1mm당 3.6MPa의 기울기를 형성하고 있었다. 용접열원에서 0.004∼0.015mm정도의 미세한 변형량이 계산되었고 좌측 자유단으로 진행하면서 0.03∼0.033mm의 변형량은 용접초기에 열충격 현상으로 발생한 것으로 사료되므로 이에 대한 대비책이 있어야 한다. 2) 용접 중반부에서는 상당 열응력 크기는 용접 초기보다 다소 작아져서 최대 51MPa, 최소 11.3MPa을 보여주며 열응력 기울기도 다소 완화된다. 이것은 용접 열원이 이동하면서 발생하는 예열효과로 상당 열응력이 감소한 것으로 사료된다. 상당 열변형의 크기는 최대 0.04mm, 최소 0.0045mm 정도를 형성하고 있고, 용접열원의 진행으로 전체적인 변형 양상이 용접진행 방향과 동일하게 이동하고 있다. 3) 용접공정의 후반부는 상당 열변형량이 최소 0.005mm, 최대 0.045mm 정도이므로, 정밀한 용접가공을 위해 반대방향에 지그나 고정구를 설치해야 한다. 상당 열응력의 구배는 모재 내부로 진행된 양상을 보이고 있으나 열응력의 절대 크기는 최소 3MPa에서 최대 27MPa로 작아졌다. 이 것은 용접의 이동열원이 제거됨으로서 모재 내부의 열응력이 현저히 저하되었음을 의미하지만, 잔류 열응력이 존재하므로 뜨임처리와 같은 후처리가 요망된다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.