• 한국재료학회지
• /
• 제11권11호
• /
• pp.947-952
• /
• 2001

The meso-scale microstructure of the $Ni-Ni_3Al- Ni_3V$ system is crucial to obtain both high strength and high toughness. Its evolution may be predicted with the aid of computer simulation of the compositional separation for heat-treated alloys. In this study, computer simulations of the hypothetical A-B-C ternary system, which is similar to the $Ni-Ni_3Al- Ni_3V$ system in terms of phase equilibria, have been performed using the kinetic modeling. Simulated morphologies were changed with nominal compositions and model parameters. It was showed the current model was useful and the more realistic model was proposed.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2010년도 춘계 학술대회 제22권1호
• /
• pp.115-116
• /
• 2010

본 연구에서는 1988년 이후에 중력하중에 대하여 설계되고 국내 철근 관행에 따라 배근된 철근콘크리트 골조 외부접합부의 거동 특성에 대하여 연구하기 위하여, 4개의 T형 부분골조 실험체를 만들고 변위비가 3.5%에 도달할 때까지 변위 하중을 가력하였다. 모든 시험체는 변비위 1%에 도달하기 전에 접합부에 파괴가 발생하여 FEMA의 제안치보다 작게 나타났으며, 종국강도가 휨 공칭강도에 의한 내력의 0.85배 이하로 나타났다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.255-257
• /
• 2004

This report presents S-N testing results of the butt and T-joint weldment which are produced by single sided welding with cenramic backing material. The specimen is designed in accordance with JISZ 3103 aid the test is peformed by the JSME S002. The nominal and hot spot stress based design S-N curves derived from fatigue tests are compared with the BS design curve. For butt and T-joint, it can be known that the double-sided butt welding process could be replaced by the single sided butt welding.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 추계학술대회 논문집
• /
• pp.7-11
• /
• 2000

In this paper was studied on the mechanical characteristics of Glass Fiber Reinforced Plastics(GFRP) of the steel bar it is to replace. The advantage of FRP such as high strength, low weight and chemical inertness or noncorrosiveness can be fully exploited. GFRP bar were successfully fabricated at l0mm nominal diameters of solid and hollow types using a pultrusion method. Tensile and bending specimens from this bar were tested and compared with behavior of GFRP rebar and steel bar.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.154-158
• /
• 2002

The mechanical properties of Al 6061 excluded bar were deformed in high temperature with the variable deformation conditions and characterized by the tensile test. Three types of different strain rate were experimentally performed by using hydraulic press, crank press and hammer and two types of the nominal strain 0.5 and 0.8 were achieved. To decide optimum forging process, the relationship among the strain rate, strain and mechanical properties was explained by analyzing the microstructures of the forged and heat heated parts. The strength was deeply related with the strain rate due to the dynamic recrystallization (DRX) in hot forging, and the best forging condition was presented in Al 6061 alloy.

• Journal of the Korean Wood Science and Technology
• /
• 제24권2호
• /
• pp.42-45
• /
• 1996

A residue from the newsprint waste was investigated as a filler in adhesive for bonding southern pine plywood. The residue was prepared by drying the wet residue to 8% moisture content and grinding the dry material using a laboratory Wiley mitt with a 75-${\mu}m$(200-mesh) screen. The residue was compared to a commercial filler commonly used in structural plywood adhesives. A total of 48 three-ply panels. 12.7mm nominal thickness and 0.3 by 0.3 m in size, were fabricated at two press times(4 and 5 min) and three assembly times(20, 40 and 60 min). Evaluations of the residue were carried out by performance tension shear tests after two 4-hour boil accelerated aging tests on plywood. The test results included tension shear strength and estimated wood failure values. All plywood made with the residue filler were comparable to the control-bonded plywood. These results indicate that residue from the newsprint waste streams would be suitable as filler for plywood adhesives.

• Computers and Concrete
• /
• 제1권2호
• /
• pp.169-188
• /
• 2004

A coupled damage-viscoplasticity model is presented for the analysis of localisation and size effects. On one hand, viscosity helps to avoid mesh sensitivity because of the introduction of a length scale in the model and, on the other hand, enables to represent size effects. Size effects were analysed by means of three-point bending tests. Correlation between the fracture energy parameter measured experimentally and the density fracture energy modelling parameter is discussed. It has been shown that the dependence of nominal strength and fracture energy on size is determined by the ligament length in comparison with the width of the fracture process zone.

• 한국철도학회논문집
• /
• 제10권4호
• /
• pp.409-413
• /
• 2007

A dynamically scaled model of the catenary with a nominal scaling factor of 18.5:1 is designed and constructed. The motivation for developing such a model is the great difficulty of making accurate measurements on the full-scale catenary and the difficulty of making experimental modifications to it. The scaled model is designed to be dynamically equivalent to the full scale catenary with respect to the mass and elastic strength. The scaled model is partially verified by comparing linear vibration and wave characteristics with those predicted by the simulation study.

• Computers and Concrete
• /
• 제11권4호
• /
• pp.351-364
• /
• 2013

This paper presents results from an analytical investigation of the behavior of steel reinforced concrete circular column sections with additional Glass Fiber Reinforced Polymers (GFRP) bars. The primary application of this composite section is to relocate the plastic hinge region from the column-footing joint where repair is difficult and expensive. Mainly, the study focuses on the development of the full nominal moment-axial load (M-P) interaction diagrams for hybrid concrete sections, reinforced with steel bars as primary reinforcement, and GFRP as auxiliary control bars. A large parametric study of circular steel reinforced concrete members were undertaken using a purpose-built MATLAB(c) code. The parameters considered were amount, location, dimensions and mechanical properties of steel, GFRP and concrete. The results indicate that the plastic hinge was indeed shifted to a less critical and congested region, thus facilitating cost-effective repair. Moreover, the reinforced concrete steel-GFRP section exhibited high strength and good ductility.

• 한국안전학회지
• /
• 제29권1호
• /
• pp.41-46
• /
• 2014

The design of a 7 degree of freedom motion capture device(MCD) has been presented. The newly designed MCD overcomes the shortcomings of the existing CADEN-7 exoskeleton robot by implementing various ergonomic design. To improve ease of operation, light-weight high-strength materials such as carbon pipes and engineering plastics were used to reduce weight of the MCD and arm-length adjustment mechanism was also added. The MCD showed consistent measurement results in designed experiments involving change of arm posture from nominal configuration to either elbow-side or arm-front configurations. Furthermore, captured motion in more natural tennis swing appeared to agree well with visual observations made.