• 한국산학기술학회논문지
• /
• 제16권12호
• /
• pp.8274-8283
• /
• 2015

텔레비전의 가스 스프링은 롱 스트로크 (200 ~ 300mm, TV 상승 변위) 하에서 작동 할 때 피스톤 속도의 제어가 가능하다. 이 원리에 의해서 사용자는 높낮이 조절이 가능하다. 먼저 피스톤의 흐름 해석을 수행하였다. 정확한 관형 단면을 위한 피스톤 속도 조절기술을 조사하였다. 유동률 제어 및 높낮이 작용을 위한 피스톤 구조를 제안되었다. 본 연구는 대형 텔레비전 스탠드를 통해 50 인치 이상 TV의 가스 스프링의 개발을 위한 것이다. 최적 피스톤 로드 제어를 위한 중공축(외경 19.9mm, 내경 13.9mm)에 질소 개스(0.3m/s)를 주입하였다. 그 결과, 유동율이 증대함에 따라 피스톤 로드의 압력강하는 외력의 변화 없이 증대되었다. 결과적으로, 가스스프링을 통한 변위의 제어는 가능하다.

• 한국산학기술학회논문지
• /
• 제16권11호
• /
• pp.7745-7753
• /
• 2015

텔레비전의 가스 스프링은 롱 스트로크 (200 ~ 300mm, TV 상승 변위) 하에서 작동 할 때 피스톤 속도의 제어가 가능하다. 이 원리에 의해서 사용자는 높낮이 조절이 가능하다. 먼저 피스톤의 흐름 해석을 수행하였다. 정확한 관형 단면을 위한 피스톤 속도 조절기술을 조사하였다. 유동률 제어 및 높낮이 작용을 위한 피스톤 구조를 제안되었다. 본 연구는 대형 텔레비전 스탠드를 통해 50 인치 이상 TV의 가스 스프링의 개발을 위한 것이다. 최적 피스톤 로드 제어를 위한 중공축(외경 19.9mm, 내경 13.9mm)에 질소 개스(0.3m/s)를 주입하였다. 그 결과, 유동율이 증대함에 따라 피스톤 로드의 압력강하는 외력의 변화 없이 증대되었다. 결과적으로, 가스스프링을 통한 변위의 제어는 가능하다.

• 플랜트 저널
• /
• 제18권3호
• /
• pp.52-61
• /
• 2022

본 연구는 실제 운영중인 영동에코발전본부 1호기 125 MW 우드펠릿 발전소를 대상으로 탈질설비 운전조건이 NOx 발생량에 미치는 영향을 시험하였다. SNCR 요소 유량 증가에 따라 NOx 농도는 점차 감소하였으나 SCR 후단 암모니아 슬립은 상승하였다. 시험대상 보일러는 고온의 내부온도로 인해 SNCR 운영에 불리한 구조이며 노즐의 최적위치 검토가 필요할 것이다. SCR 희석공기 온도변화는 NOx 발생량에 영향을 미치지 않았다. SCR 암모니아 유량 증가는 SCR 후단 NOx 농도를 감소시켰고 NOx 제거효율도 증가시켰다. 다만 암모니아 슬립 자체 기준치를 초과하지 않는 암모니아 유량 111 kg/h가 최대 운전기준으로 추정된다. SCR 믹서 압력 상승은 NOx 농도를 감소시키고 제거효율도 최대로 측정되어 NOx 생성을 가장 효과적으로 억제하는 변수로 파악되었다.

• 상하수도학회지
• /
• 제29권2호
• /
• pp.261-269
• /
• 2015

In this study, we applied a membrane distillation process to investigate a feasibility of treating a wastewater with high concentration of organic matters including nitrogen and phosphorus. The laboratory scale experiment was performed by using a hydrophobic PVDF membrane with the pore size of $0.22{\mu}m$ and porosity of 75%. The installation was direct contact type where the temperature difference between a feed and permeate side was controlled to have a range from 20 to $60^{\circ}C$. We observed a flux variation and a concentration changes of COD, $PO{_4}^{3-}$-P, $NH_4{^+}$-N and conductivity of feed side as well as permeate side with various temperature differences (20 to $60^{\circ}C$), cross flow velocities (0.09 to 0.27 m/s) through the module, and pH (6.6 to 12.0) of the feed that has the initial concentration of COD about 1,000 mg/L, total nitrogen 390 mg/L, total phosphorus 10 mg/L, conductivity of $7,000{\mu}s/cm$. The results showed that the average flux was ranged from 4 to $40L/m^2/hr$ which was almost similar with the flux of NaCl and deionized water used as a feed solution. The lowest flux was obtained at the operating condition with the temperature difference of $20^{\circ}C$ and cross flow velocity of 0.09 m/s while the highest one was measured with $60^{\circ}C$ and 0.27 m/s. Above 99% of COD and $PO{_4}^{3-}$-P in the feed could be rejected regardless of an operating condition. However, the removal rate of ammonium nitrogen was varied from 64 to 99% depending on the pH of feed solution.

• 한국환경과학회지
• /
• 제21권11호
• /
• pp.1321-1331
• /
• 2012

To date, carbon and nitrogen co-doped photocatalysts (CN-$TiO_2$) for environmental application focused mainly on the aqueous phase to investigate the decomposition of water pollutants. Accordingly, the present study explored the photocatalytic performance of CN-$TiO_2$ photocatalysts for the purification of indoor-level gas-phase aromatic species under different operational conditions. The characteristics of prepared photocatalysts were investigated using X-ray diffraction, scanning emission microscope, diffuse reflectance UV-VIS-NIR analysis, and Fourier transform infrared (FTIR) analysis. In most cases, the decomposition efficiency for the target compounds exhibited a decreasing trend as input concentration (IC) increased. Specifically, the average decomposition efficiencies for benzene, toluene, ethyl benzene, and xylene (BTEX) over a 3-h process decreased from 29% to close to zero, 80 to 5%, 95 to 19%, and 99 to 32%, respectively, as the IC increased from 0.1 to 2.0 ppm. The decomposition efficiencies obtained from the CN-$TiO_2$ photocatalytic system were higher than those of the $TiO_2$ system. As relative humidity (RH) increased from 20 to 95%, the decomposition efficiencies for BTEX decreased from 39 to 5%, 97 to 59%, 100 to 87%, and 100 to 92%, respectively. In addition, as the stream flow rates (SFRs) decreased from 3.0 to 1.0 L $min^{-1}$, the average efficiencies for BTEX increased from 0 to 58%, 63 to 100%, 69 to 100%, and 68 to 100%, respectively. Taken together, these findings suggest that three (IC, RH, and SFR) should be considered for better BTEX decomposition efficiencies when applying CN-$TiO_2$ photocatalytic technology to purification of indoor air BTEX.

• 한국재료학회지
• /
• 제9권5호
• /
• pp.503-508
• /
• 1999

We have investigated the physical and diffusion barrier property of Ti-Si-N film for Cu metallization. The ternary compound was deposited by using reactive rf magnetron sputtering of a TiSi$_2$target in an Ar/$N_2$gas mixture. Resistivities of the films were in range of 358$\mu$$\Omega$-cm, to 307941$\mu$$\Omega$-cm, and tended to increase with increasing the $N_2$/Ar flow rate ratio. The crystallization of the Ti-Si-N compound started to occur at 100$0^{\circ}C$ with the phases of TiN and Si$_3$N$_4$identified by using XRD(X-ray Diffractometer). The degree of the crystallization was influenced by the $N_2$/Ar flow ratio. The diffusion barrier property of Ti-Si-N film for Cu metallization was determined by AES, XRD and etch pit by secco etching, revealing the failure temperature of 90$0^{\circ}C$ in 43~45at% of nitrogen content. In addition, the very thin compound (10nm) with 43~45at% nitrogen content remained stable up to $700^{\circ}C$. Furthermore, thermal treatment in vacuum at $600^{\circ}C$ improved the barrier property of the Ti-Si-N film deposited at the $N_2$(Ar+$N_2$) ratio of 0.05. The addition of Ti interlayer between Ti-Si-N films caused the drastic decrease of the resistivity with slight degradation of diffusion barrier properties of the compound.

• Bulletin of the Korean Chemical Society
• /
• 제31권5호
• /
• pp.1267-1269
• /
• 2010

The pure crystalline $Li_{1.1}V_{0.9}O_2$ powder has been prepared by a simple solid state reaction of $Li_2CO_3$ and $V_2O_3$ precursors under nitrogen gas containing 10 mol % hydrogen gas flow. The structure of $Li_{1.1}V_{0.9}O_2$ powder was analyzed using Xray diffraction (XRD) and scanning electron microscope (SEM). The stoichiometric $Li_{1.1}V_{0.9}O_2$ powder was used as anode active material for lithium secondary batteries. Its electrochemical properties were investigated by cyclic voltammetry and constant current methods using lithium foil electrode. The observed specific discharge capacity and charge capacity were 360 mAh/g and 260 mAh/g during the first cycle, respectively. In addition, the cyclic efficiency of this cell was 72.2% in the first cycle. The specific capacity of $Li_{1.1}V_{0.9}O_2$ anode rapidly declines as the current rate increases and retains only 30 % of the capacity of 0.1C rate at 1C rate. The crystallinity of the $Li_{1.1}V_{0.9}O_2$ anode decrease as discharge reaction proceeds. However, the relative intensity of main peaks was almost recovered when the cell was charged up to 1.5 V.

• 한국결정학회지
• /
• 제11권1호
• /
• pp.16-21
• /
• 2000

(Yb/sub x/Y/sub 1-x/)Ca₄O(BO₃)₃ single crystals where x=0.3,8,15,20% were grown by Czochralski Method. The crystals grown under the optimum conditions were transparent and colorless with good crystal form. Using polarizing microscope, crystal defects such as parasite crystals and bubbles were detected depending on the composition of melts and pulling rates. The optimum growth parameters for high quality of single crystals were 15∼20 rpm of rotation rate and 2mm/h of pulling rate at the flow rate of 2 l/min of Nitrogen gas. The relationship between crystal axes and optical axes was investigated by optical crystallographic method, polarization technique and single crystal X-ray method. From the spectroscopic measurements, it was confirmed that there were strong absorption bands at 900 and 976.4 nm and strong emission band at 976.4 nm in Yb/sup 3+/ ion doped YCa₄O(BO₃)₃ crystal. For the application of second harmonic generation of 1.064 ㎛ laser, non-linear optical devices with θ=32.32° and Ψ=0°, λ/10 of flatness and the size of 6x8x5.73 mm were fabricated from the grown YCa₄O(BO₃)₃ crystal.

• Fisheries and Aquatic Sciences
• /
• 제14권4호
• /
• pp.363-369
• /
• 2011

Total ammonia nitrogen (TAN) removal efficiencies of a sand filter (SF), polystyrene microbead filter (PF), and Kaldnes bead filter (KF) media were evaluated under ammonia loading rates of 5, 25, and 50 g $m^{-3}day^{-1}$. The volume of each filter media tested was 7 L, and the water flow rate for all filter media was 24 L/min. The specific surface areas of the SF, PF, and KF were 7,836, 3,287, and 500 $m^2/m^3$, respectively. Sand was fluidized and the other two media were trickle filtered. The volumetric TAN removal rate increased with increasing ammonia loading rate for all filter media. Mean volumetric TAN removal rates under the ammonia loading rates of 5, 25, and 50 g $m^{-3}day^{-1}$ in SF (39.3, 168.6, and 322.7 g $m^{-3}day^{-1}$, respectively) were higher than those in PF (35.0, 157.4, and 310.5 g $m^{-3}day^{-1}$, respectively) and KF (32.1, 142.5, and 288.1 g $m^{-3}day^{-1}$, respectively). These results were related to differences in the specific surface areas of the filter media. PF was the most economic media for efficiently removing TAN.

• 조명전기설비학회논문지
• /
• 제16권6호
• /
• pp.95-101
• /
• 2002

고농도의 오존발생에 영향을 주는 많은 변수들이 존재한다. 이러한 변수들은 오존발생장치 설계시 매우 중요한 요소가 되고 설계전에 반드시 고려되어야 할 것들이다. 오존발생장치 설계 후에도 고농도 오존발생에 크게 영향을 주는 주변변수들이 있다. 본 연구에서는 오존발생에 영향을 주는 많은 주변변수들중에서 입력산소가스의 유량과 여기에 첨가되는 첨가가스가 고농도의 오존발생에 미치는 영향을 조사하였다. 결과적으로, 입력산소가스의 유량을0.75[LPM］～2.00[LPM］으로 변화시키면서 오존농도를 측정한 결과 1.25［LPM］에서 71145［ppm］의 최대오존발생량을 보여주었다. 입력산소가스에 첨가되는 질소가스의 유량을 0.0［vol%］～6.4［vol%］으로 변화시켜가면서 발생되는 오존농도를 측정한 결과 첨가되는 질소가스량이 0.8［vol%］인 경우 최대 73135［ppm]의 오존을 얻을 수 있었다. 이것은 순수산소만을 입력가스로 사용했을 때보다 최대오존발생량이 3［%］가량 증가한 결과이다. 입력산소가스에 첨가되는 아르곤가스의 유량을 0.0[vol%］～6.4[vol％］으로 변화시켜가면서 발생되는 오존농도를 측정한 결과 첨가되는 아르곤가스량이 0.8［vol%］인 경우 최대 67288［ppm］의 오존을 얻을 수 있었다.