• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.549-552
• /
• 1999

We have developed an novel vertical-alignment (VA) - $\pi$ cell mode that provides a wide viewing angle and fast response times for negative dielectric anisotropy nematic liquid crystal (NLC) on a homeotropic polyimide (PI) surfaces. We had the good voltage-transmittance curves and low driving voltages were achieved with the novel VA - $\pi$ cell mode without negative compensation film. Iso-viewing angle characteristics using the novel VA - $\pi$ cell mode without negative compensation film of NLC was also successfully observed. As well a fast response time of 31.7ms for the novel VA - $\pi$ cell mode was measured. Consequently, It is seen that by using the novel VA - $\pi$ cell mode the iso-viewing angle, fast response time, and low driving voltage characteristics can be achieved.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.515-518
• /
• 2000

We studied the viewing angle characteristics of a negative dielectric anisotropy nematic liquid crystal (NLC) using the new vertical-alignment (VA)-1/6 cell on a rubbed polyimide (PI) surface. Good voltage-transmittance (V-T)characteristics using the new VA-1/6 cell without a negative compensation film were obtained. The iso-viewing angle characteristics using the new VA-1/6 cell without the negative compensation film can be achieved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.6
• /
• pp.661-667
• /
• 2004

The control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by hot plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC (Δ$\varepsilon$＞0) on the rubbed homeotropic PI surface by increasing temperature and time was measured. The tilt angle of positive type NLC(Δ$\varepsilon$＞0) is smaller than that of the negative type (Δ$\varepsilon$＞0) on rubbed PI with increasing baking temperature and time. We consider that the tilt angle of NLC is decreased due to increasing the steric interaction between horizon component of permittivity $\varepsilon$ = of NLC and the stress of polymer side chain by high temperature. As the increase of baking temperature, we obtain that AFM (atomic force microscope) image of rubbed PI surface using Hot-plate method has formed better solid micro-groove structure than oven method.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.67-70
• /
• 2003

The control of tilt angle for nematic liquid crystal (NLC) with negative and positive dielectric anisotropy on the rubbed homeotropic polyimide (PI) using baking method by hot plate equipment was investigated. LC tilt angle decreased with increasing baking temperature and time. Especially, the low LC tilt angle of positive type NLC ($\Delta\varepsilon$ >0) on the rubbed homeotropic PI surface by increasing temperature and time was measured. The tilt angle of positive type NLC ($\Delta\varepsilon$ >0) is smaller than that of the negative type ($\Delta\varepsilon$ >0) on rubbed PI with increasing baking temperature and time. We consider that the tilt angle of NLC is decreased due to increasing the steric interaction between horizon component of permittivity $\varepsilon$ = of NLC and the stress of polymer side chain by high temperature.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1169-1172
• /
• 2004

Polyimides are blended with photoreactive polymers in order to improve the thermal stability of molecular orientation of photoreactive groups induced by polarized UV irradiation. The polyimide/photopolymer blends can be applied for the photo-induced liquid crystal alignment layers. However, the polyimides are also decomposed by UV irradiation and this may have the negative effect on the orientation of liquid crystals. In order to elucidate the influence of polyimide on the molecular orientation of liquid crystal, non-photoreactive naphthalenic polyimide (1,4,5,8-naphthalene tetracarboxylic dianhydride} was selected for the blend alignment layers. We prepared the blends of photo-reactive coumarin polymers and naphthalenic polyimide, and investigated the orientation of liquid crystals. Thermal stability of the orientation of liquid crystals was enhanced due to the thermally stable polyimide. However, there was no other side-effect of polyimide on the orientation of liquid crystals and this might be attributed to the non-photo-reactivity of naphtahlenic polyimide.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.949-952
• /
• 2002

The mechanisms of pretilt angle generation for a nematic liquid crystal (NLC) with negative dielectric anisotropy on the blended polyimide (PI) surface containing trifluoromethyl moiety was studied. High LC pretilt angle on the blended polymer surface with F3 was measured and the pretilt angle increased with rubbing strength. However, the low LC pretilt angle on the blended polymer surface with F1 and F2 was measured. The high LC pretilt angle generated is attributable to trifluoromethyl moiety in backbone structure on the blended PI surface. Therefore, the high pretilt angle of NLC can be achieved by using the blended polymer surface.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.11
• /
• pp.981-984
• /
• 2002

The mechanisms of pretilt angle generation for a nematic liquid crystal (NLC) with negative dielectric anisotropy on the blended polyimide (PI) surface containing trifluoromethyl moiety were studied. High LC pretilt angle on the blended polymer surface with F3 was measured and the pretilt angle increased with rubbing strength. However, the low LC pretilt angle on the blended polymer surface with F1 and F2 was measured. The high LC pretilt angle generated is attributable to trifluoromethyl moiety in backbone structure on the blended PI surface. Therefore, the high pretilt angle of NLC can be achieved by using the blended polymer surface.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.563-566
• /
• 2004

We have studied a electrically controlled birefringence (ECB) mode for field sequential liquid crystal display (FSLCD). We measured response time of the ECB mode. The ECB mode exhibiting fast response time, high transmittance, low operating voltage and adequate viewing angle. The positive liquid crystal (LC) is better than negative LC on dielectric anisotropy, birefringence and rotational viscosity. So that, the ECB mode is one of strongest candidate for FSLCD application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.337-340
• /
• 2001

The control of high pretilt angle far nematic liquid crystal (NLC) with negative dielectric anisotropy on the rubbed blending polyimide (homeotropic and homogeneous alignment) surface were studied. High NLC pretilt angle generated on the blending polyimide (homeotropic polyimide and SE-7492 surface was measured and the NLC pretilt angle increases with blending ratio and rubbing strength. However, the NLC pretilt angle generated on the blending polyimide (homeotropic polyimide and SE-150 surface was not varied. The high pretilt angle the NLC using blending polyimide surface can be acheived.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.337-340
• /
• 2001

The control of high pretilt angle for nematic liquid crystal (NLC) with negative dielectric anisotropy on the rubbed blending polyimide (homeotropic and homogeneous alignment) surface were studied. High NLC pretilt angle generated on the blending polyimide (homeotropic polyimide and SE-7492 surface was measured and the NLC pretilt angle increases with blending ratio and rubbing strength. However, the NLC pretilt angle generated on the blending polyimide (homeotropic polyimide and SE-150 surface was not varied. The high pretilt angle the NLC using blending polyimide surface can be achieved.