• Macromolecular Research
• /
• v.9 no.2
• /
• pp.92-99
• /
• 2001

Silica-filled rubber compounds have slower cure characteristics than carbon black-filled ones due to the adsorption of curatives on the silica surface. Fatty acid was used as a cure activator along with zinc oxide in a sulfur cure system. Poly(ethylene glycol), PEG, was used in silica-filled rubber compounds to prevent adsorption of the curatives on the silica surface. In this study, influence of the size of fatty acid and PEG on properties of silica-filled NR compounds was investigated. It was found that the size of fatty acid and PEG affected the curt: characteristics and physical properties. The cure rate becomes faster as the PEG size increases. By increasing the size of fatty acid or PEG, the delta torque of the compound decreases while the Mooney viscosity increases. The modulus of the vulcanizate decreases with increasing the molecular weight of fatty acid or PEG. The experimental results were explained by the filler dispersion and by the prevention of the curative-adsorption on the silica surface.

• Elastomers and Composites
• /
• v.33 no.5
• /
• pp.335-344
• /
• 1998

In this study, the tearing energy and the rate of crack propagation of natural rubber (NR) compounds were evaluated to improve the crack resistance of tank-track pads. Although the factors affecting the crack resistance properties of NR compounds are various in this experiment, the effects of filler(carbon black) and the crosslinking system were evaluated. When the amount of accelerator is equal to that of sulfur( eg. efficient vulcanization), the compound shows the most excellent in the aged mechanical properties and the crack resistance properties. The ISAF carbon black(CB) having a good reinforcing characteristics was better than any other CB grades in physical properties and processablity. The optimum content was 50phr.

• Elastomers and Composites
• /
• v.40 no.1
• /
• pp.29-36
• /
• 2005

Mixing condition and procedure affect properties or a filled rubber compound such as filler dispersion, viscosity, and bound rubber formation. Influence of separate load of styrene-butadiene rubber (SBR) and acrylonitrile-butadiene rubber (NBR) on properties or silica-filled SBR compounds containing NBR was studied. Cure time and cure rate became faster as NBR content increased. The crosslink density increased with increase in the NBR content. The bound rubber content also increased as the NBR content increased. NBR content of the bound rubber was higher than that of the compounded rubber. The bound rubber content was higher when SBR and NBR were loaded separately than when loading simultaneously. The cure time and cure rate were slower for the separate load than for the simultaneous one. The crosslink density was also lower for the former case than for the latter one.

• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.167-175
• /
• 2020

Various studies have been conducted to improve silica dispersion of silica filled tire tread compounds; among them, silica wet masterbatch (WMB) technology is known to be suitable for manufacturing silica filled compounds that have high silica content and high dispersibility. Till now, the WMB study is focused on the natural rubber (NR) or emulsion styrene-butadiene rubber (ESBR) that does not have a silica-affinity functional group, and a study of NR or ESBR having a silica-affinity functional group is still not well known. Unlike the dry masterbatch technology, the WMB technology can solve the problems associated with the high Mooney viscosity when applied to silica-friendly rubber. However, a coagulant suitable for each functional group has not yet been determined. Therefore, in this study, different coagulant applied silica WMB was prepared by applying calcium chloride, sulfuric acid, acetic acid, and propionic acid by using a carboxyl group functionalized reversible addition fragmentation chain transfer ESBR. The evaluation of the WMB compounds revealed that the calcium chloride added WMB compound showed excellent silica dispersion, abrasion resistance, and rolling resistance.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.565-572
• /
• 1996

The optimum loading of carbon black was studied for the rubber compounds of natural rubber(NR), butadiene rubber(BR), and styrene-butadiene rubber(SBR) with different amount of oil. The optimum loading of carbon black was determined by the volume ratio of carbon black and L factor of Lee's theory. The optimum loading of carbon black was confirmed by the examination of physical properties of the rubbers. The optimum loading amounts of carbon black for the each rubber compound were 60 phr for NR, 57 phr for BR, 65 phr for SBR-A, 70 phr for SBR-B, and 76 phr for SBR-C, respectively. The optimum loading of carbon black was increased by 5 phr for every increment of 20 phr of oil content. It was revealed that the optimum loading amount of carbon black determined by L factor is closely related to the tensile strength of the rubber compounds. The optimum loading amount of carbon black was observed at the amount which shows the maximum value of tensile strength.

• Elastomers and Composites
• /
• v.33 no.4
• /
• pp.281-289
• /
• 1998

Tensile properties including Young's modulus and tear strength were measured for four different rubber compounds; natural rubber(NR), styrene-butadiene copolymer(SBR), ethylene-propylene diene monomer (EPDM), and brominated isobutylene-p-methyl-styrene copolymer(BIMS) as a function of temperature and degree of cure. To see the effect of over cure, a measurement was made of the tensile strength and swelling behavior of the over-cured rubber compounds. Young's modulus, E, was found to have linear dependency on the degree of cure for all rubber compounds. EPDM and BIMS showed the highest and lowest slopes, respectively. The slope of NR and SBR lay between EPDM and BIMS. Tear strength, Gc, decreased in the order of NR>BIMS>SBR>EPDM. As the cure time was extended the degree of cure of NR and SBR decreased, while that of BIMS increased. EPDM showed little change in the degree of cure.

• Polymer(Korea)
• /
• v.25 no.1
• /
• pp.63-70
• /
• 2001

The objective of this study was to investigate the effect of cure type on the processing and physical properties under conditions of similar stress-strain properties. On the carbon black filled natural rubber(NR) based compound, the induction time decreased, but the cure rate became fast with increasing loading of sulfur donor agent. Tensile strength was little affected on the curing type. However, elongation generally decreased with increasing accelerator. Effect of cure type on the blow-out properties was followings: CV

• Elastomers and Composites
• /
• v.58 no.4
• /
• pp.161-172
• /
• 2023

Because particulate matter has emerged as a major contributor to air pollution, the tire industry has conducted studies to reduce particulate matters from tires by improving tire performance. In this study, we compared the conventional blending method, in which rubber, filler, and additives are mixed simultaneously, to the Y-blending method, in which masterbatches are blended. We manufactured carbon black (CB)-filled natural rubber (NR)/butadiene rubber (BR) blend and silica-filled epoxidized NR/BR blend compounds to compare the effects of the two blending methods on the physical properties of the compounds and the amount of particulate matter generated. The Y-blending method provided uniform filler distribution in the heterogeneous rubber matrix, improved processability, and exhibited low rolling resistance. This method also improved physical properties owing to the excellent filler-rubber interaction. The results obtained from measuring the generation of particulate matter indicated that, the Y-blending method reduced PM_2.5 particulate matter generation from the CB-filled and silica-filled compounds by 38% and 60%, and that of PM₁₀ by 29% and 67%, respectively. This confirmed the excellence of the Y-blending method regarding the physical properties of truck bus radial tire tread compounds and reduced particulate matter generated.

• Elastomers and Composites
• /
• v.21 no.1
• /
• pp.13-19
• /
• 1986

The effects of several vulcanizing accelerators on the determination of kinetic parameters of natural rubber vulcanizate was studied by DSC. Kinetic parameters were determined by means of the calculation procedures of Borchardt-Daniels and Oscillating Disk Rheometer (ODR) cure curve analysis, using both DSC exothermal thermogram and ODR cure curve. In order to examine the credibility in the DSC method the same compound which was und for DSC method was used for the comparison with the results of ODR data. Upon this method, kinetic rate constant (k), and Arrehenius parameter (Ea, ko, n) have been determined for rubber compounds via a new method using DSC thermogram and ODR cure curve. In the comparison of DSC and ODR results, kinetic parameters has shown good agreements between two results. Consequently, from the present studies, it is shown that the DSC thermoanalytical method can provide an alternate new method of kinetic study of rubber vulcanization.

• Elastomers and Composites
• /
• v.37 no.2
• /
• pp.86-98
• /
• 2002

The application of silica/carbon black dual phase fillers to natural rubber(NR) compound was investigated. When the amounts of filler content were restricted to 60phr, the optimum ratio of dual phase fillers were 25phr/35phr of silica/carbon black. It was found that these new fillers give better overall performance in comparison with carbon black in tear strength, crack resistance, and cutting resistance. Also the thermal degradation resistance of NR vulcanizates which were filled with dual phase fillers was better than that of the carbon black. Dual phase fillers filled NR vulcanizates showed better viscoelastic properties, like tan${\delta}$, for the wet skid resistance and rolling resistance of motor vehicle tires.