• Resources Recycling
• /
• v.27 no.2
• /
• pp.24-31
• /
• 2018

In this study, waste ITO target is dissolved into hydrochloric acid to generate a complex indium-tin chloride solution. Nano sized ITO powder with an average particle size below 30 nm are generated from these raw material solutions by spray pyrolysis process. Also, in this study, thermodynamic equations for the formation of indium-tin oxide (ITO) are established. As the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$, the proportion and size of the spherical droplet shape in which nano sized particles aggregated gradually decreased, and the surface structure gradually became densified. When the reaction temperature was $800^{\circ}C$, the average particle size of the generated powder was about 20 nm, and no significant sintering was observed. At a reaction temperature of $900^{\circ}C$, the split of the droplet was more severe than at $800^{\circ}C$, and the rate of maintenance of the initial atomized droplet shape decreased sharply. The average particle size of the powder formed was about 25 nm. The ITO particles were composed of single solid crystals, regardless of reaction temperature. XRD analysis showed that only the ITO phase was formed. Remarkably, the specific surface area decreased by about 30% as the reaction temperature increased from $800^{\circ}C$ to $900^{\circ}C$.

• Journal of Powder Materials
• /
• v.11 no.6 s.47
• /
• pp.467-471
• /
• 2004

In order to fabricate a high density sintered body of ITO, nano-sized ITO powders were synthesized by coprecipitation methods. Aqueous solutions of indium and tin salts were mixed and coprecipitated by changing their pH. Coprecipitated ITO powders possessed 20-30 nm crystallite size and a relatively high BET value ($35m^2/g$), however, aggregation of particles were occurred. Therefore, a novel recrystallization technique was applied in order to eliminate the aggregates. The recrystallized ITO material consists of a little bit larger needlelike crystals, $20nm{\times}80nm$, and it possesses a higher BET value $(57m^{2}/g)$ compared to the plain coprecipitated material $(35m^{2}/g)$. Metastable phase formation and higher content of aggregated particles were observed in the coprecipitated materials. Densification was 95% to 98% complete after 5 hour sintering at $1500^{\circ}C$ for the recrystallized powders while densities of the coprecipitated powders were below 75%.

• Resources Recycling
• /
• v.16 no.1 s.75
• /
• pp.28-36
• /
• 2007

Nano-sized ITO powders with the average particle size below 50 nm were synthesized from complex acid solution dissolved the ITO target into hydrochloric acid by a spray pyrolysis process, and the influences of reaction factors as reaction temperature and concentration of raw material solution were investigated. As the reaction temperature increases from 800 to $1000^{\circ}C$, the average particle size of the ITO powder increases from 40 nm to 100 nm, the microstructure gradually becomes solid, individual particles independently appear with the shape of polygon, the particle size distribution becomes increasingly irregular, the XRD peak intensity gradually increases and the specific surface area decreases. As the concentration of the raw material solution increases from 50g/l to 400g/l, the average particle size of ITO powder gradually increases, yet the particle size distribution appears more irregular. When the concentration is at 50 g/l, the average particle size of ITO powder is below 30 nm and the particle size distribution appears comparatively uniform. Nevertheless, when the concentration reaches 400 g/l, which is close to e saturated concentration, the particle size distribution appears extremely irregular, and the particles with the size ranging from 20 nm to 100 nm coexist. Along with the concentration rise, the XRD peak intensity gradually increases, yet the specific surface area decreases.

• Journal of the Korean Applied Science and Technology
• /
• v.31 no.4
• /
• pp.694-702
• /
• 2014

The micron-sized ITO(indium tin oxide) particles were prepared by spray pyrolysis from aqueous precursor solutions for indium, and tin and organic additives solution. Organic additives solution with citric acid(CA) and ethylene glycol(EG) were added to aqueous precursor solution for Indium and Tin. The obtained ITO particles prepared by spray pyrolysis from the aqueous solution without organic additives solution had spherical and filled morphologies whereas the obtained ITO particles with organic additives solution had more hollow and porous morphologies with increasing mole of organic additives. The micron-sized ITO particle with organic additives was changed fully to nano-sized ITO particle whereas the micron-sized ITO particle without organic additives was not changed fully to nano-sized ITO particle after post-treatment at $700^{\circ}C$ for 2 hours and wet-ball milling for 24 hours. The size of primary ITO particle by Debye-Scherrer formula and surface resistance of ITO pellet were measured.

• Journal of Powder Materials
• /
• v.15 no.6
• /
• pp.450-457
• /
• 2008

The objectives of this study were the development of a synthesis technique for highly active nanosized ITO powder and the understanding of the reaction mechanisms of the ITO precursors. The precipitation and agglomeration phenomena in ITO and $In_{2}O_{3}$ precursors are very sensitive to reaction temperature, pH, and coexisting ion species. Excessive $Cl^-$ ion and $Sn^{+4}$ ions had a negative effect an synthesizing highly active powders. However, with a relevant stabilizing treatment the shape and size of ITO and $In_{2}O_{3}$ precursors could be controlled and high density sintered products of ITO were obtained. By applying the reprecipitation process (or stabilization technique), highly active ITO and $In_{2}O_{3}$ powders were synthesized. Sintering these powders at $1500^{\circ}C$ for 5 hours produced 97% dense ITO bodies.

• Resources Recycling
• /
• v.13 no.6
• /
• pp.16-25
• /
• 2004

In this study, nano-sized indium oxide powder with the average particle size below 100 nm is prepared from the indium chloride solution by the spray pyrolysis process. The effects of the concentration of raw material solution, the nozzle tip size and the air pressure on the properties of powder were studied. As the indium concentration of the raw material solution increased from 40 g/l to 350 g/l, the average particle size of the powder gradually increased from 20 nm to 60 nm, yet the particle size distribution appeared more irregular, the intensity of a XRD peak increased and specific surface area decreased. As the nozzle tip size increased from 1 nm to 5 nm, the average particle size of the powder increased from 40 nm to 100 nm, the particle size distribution was much more irregular, the intensity of a XRD peak increased and specific surface area decreased. As the air pressure increased from 0.1 kg/cm$^2$ to 0.5 kg/cm$^2$, the average particle size of the powder varies slightly upto 90~100 nm. As the air pressure increased from 1 kg/cm$^2$ to 3 kg/cm$^2$, the average particle size decreased upto 50~60 nm, the intensity of a XRD peak decreased and the specific surface area increased.