• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.765-768
• /
• 2009

In this work, we prepared the activated multi-walled carbon nanotubes (Acti-MWNTs) with well developed physical surface structures, high specific surface area, and higher adsorption capacity by a physical activation process, in order to enhance the hydrogen storage capacity. The Acti-MWNTs' changes in the crystalline phase and in their lattice distortions were characterized by X-ray diffraction (XRD). The textural properties of the Acti-MWNTs were investigated by a nitrogen adsorption isotherms by Brunauer-Emmett-Teller (BET) equation and Harvath-Kawazoe (H-K) calculation, respectively. The hydrogen storage capacity of the Acti-MWNTs was investigated by BEL-HP at 298 K/100 bar. The hydrogen storage capacity of the Acti-MWNTs was improved with the physical activation, resulted from the formation of new hydrogen-favorable sites on the Acti-MWNT surfaces. In conclusion, the physical activation was one of the effective method to enhance the hydrogen storage capacity of the MWNTs.

• Journal of Powder Materials
• /
• v.16 no.4
• /
• pp.280-284
• /
• 2009

The pressureless sintering behavior of $Al_2O_3$/Cu powder mixtures, prepared from $Al_2O_3$/CuO and $Al_2O_3$/Cu-nitrate, has been investigated. Microstructural observation revealed that $Al_2O_3$ powders with nano-sized Cu particles could be synthesized by hydrogen reduction method. The specimens, pressureless-sintered at $1400^{\circ}C$ for 4 min using infrared heating furnace with the heating rate of $200^{\circ}C$/min, showed the relative density of above 90%. Maximum hardness of 16.1 GPa was obtained in $Al_2O_3$/MgO/Cu nanocomposites. The nanocomposites exhibited the enhanced fracture toughness of 4.3-5.7 $MPa{\cdot}m^{1/2}$, compared with monolithic $Al_2O_3$. The mechanical properties were discussed in terms of microstructural characteristics.

• Journal of Powder Materials
• /
• v.16 no.3
• /
• pp.209-216
• /
• 2009

A composite of rapidly solidified Al-6061 alloy powder with graphite particle reinforcements was prepared by ball milling and subsequent hot extrusion. The microstructure and mechanical properties of these composites were investigated as a function of milling time. With increasing milling time, the gas atomized initially and spherical powders became elongated with a maximum aspect ratio after milling for 30 h. Then, refinement and spheroidization were achieved by further milling to 70 h with a homogeneous and fine dispersion of graphite particles forming between the matrix alloy layers. The best compression and wear properties were obtained in the powder milled for 70 h, associated with the increased fine and homogeneous distribution of graphite particles in the aluminum alloy matrix.

• Journal of Powder Materials
• /
• v.12 no.6 s.53
• /
• pp.393-398
• /
• 2005

In-situ processing route was adopted to disperse carbon nanotubes (CNTs) into $Al_2O_3$ powders homogeneously. The $Al_2O_3$ composite powders with homogeneous dispersion of CNTs could be synthesized by a catalytic route for in-situ formation of CNTs on nano-sized Fe dispersed $Al_2O_3$ powders. CNTs/Fe/$Al_2O_3$ nanopowders were densified by spark plasma sintering (SPS). The hardness and bending strength as well as electrical conductivity increased with increasing sintering temperature. However, the electrical conductivity of the composites sintered at above $1500^{\circ}C$ showed decreased value with increasing sintering temperature due to the oxidation of CNTs.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.12
• /
• pp.2481-2485
• /
• 2007

Spatially resolved, quantitative, non-destructive analysis using synchrotron x-ray reflectivity (XR) with subnano-scale resolution was successfully performed on the nanoporous organosilicate thin films for low dielectric applications. The structural information of porous thin films, which were prepared with polymethylsilsesquioxane and thermally labile 4-armed, star-shaped poly(ε-caprolactone) (PCL) composites, were characterized in terms of the laterally averaged electron density profile along with a film thickness as well as a total thickness. The thermal process used in this work caused to efficiently undergo sacrificial thermal degradation, generating closed nanopores in the film. The resultant nanoporous films became homogeneous, well-defined structure with a thin skin layer and low surface roughness. The average electron density of the calcined film reduced with increase of the initial porogen loading, and finally leaded to corresponding porosity ranged from 0 to 22.8% over the porogen loading range of 0-30 wt%. In addition to XR analysis, the surface and the inner structures of films are investigated and discussed with atomic force and scanning electron microscopy images.

• Journal of the Korean Ceramic Society
• /
• v.43 no.3 s.286
• /
• pp.193-197
• /
• 2006

Symmetric three-layer $Al_2O_3/ZrO_2$ composite has been prepared by freeze casting and pressureless sintering at $1400-1600^{\circ}C$ in air. The layered material sintered at $1600^{\circ}C$ showed the maximum fracture strength (410 MPa), measured by a four-point bending test. Contact damage strength was superior in three-layer composite compared with corresponding mono-layered material, possibly due to the development of relatively large compressive stress. The grain growth of $ZrO_2$ particles was mainly governed by coalescence mechanism.

• Journal of the Korean Ceramic Society
• /
• v.45 no.2
• /
• pp.99-104
• /
• 2008

Zeta potential, sedimentation bulk density and rheology in the dispersion system have been studied in terms of solid loading (40-55 vol%), and types of additives. Ammonium polymethacrylate, glycerol, ethoxylated acetylenic diol, and polyvinyl alcohol have been used as the dispersant, cryo-protectant, surfactant, and binder, respectively. Sedimentation density greatly increased upon adding dispersant; the effect was more pronounced with ionic alumina suspension compared with covalent silicon carbide. With further addition of cryo-protectant and surfactant to dispersant, the sedimentation density increased somewhat. The suspension viscosity generally behaviored in an opposite manner to the sedimentation density, i.e., high sedimentation gave low high-shear viscosity, indicative of low order structure formation in the suspended particles. Shear rate rheology in shear rate of $2-300\;sec^{-1}$ showed a shear thinning and its onset began at similar shear rate (${\sim}100\;sce^{-1}$), regardless of solid loading.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.260-260
• /
• 2010

In recent years, polymer/clay nanocomposites have generated a great interest, both in industry and in academia, because they often exhibit remarkable improvement in material properties when compared with the virgin polymer or conventional micro and macro-composites. Among these properties are stiffness, strength, dimensional stability and permeability. [1-3] The dispersion of hydrophilic silicates in a hydrophobic matrix like Polyethylene (PE) is difficult because of the difference in character between PE and Montmorillonite (MMT). Therefore, it is necessary to modify PE with polar groups, which can increase the hydrophilicity of PE. In this study, High density polyethylene (HDPE)/$Mg(OH)_2$/Montmorillonite (MMT) nanocomposites having a various compositions were prepared by a melt blending technique with an internal mixer and properties namely mechanical, morpology, rheological and thermal properties were investigated

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.82-82
• /
• 2010

에폭시메트릭스 내에서 초음파 및 균질기를 이용하여 층상실리케이트 마이크로 입자의 균질분산을 위하여 사용하였다. 초음파와 균질기를 동시에 사용하여 최적의 적용시간과 충진나노입자 충진함량과의 관계를 연구하기위하여 구조적 특성으로 X-RD, 열적특성으로 DSC, 열적 기계적 특성으로 DMA를 사용하여 특성을 평가하였다. 충진함량 변화에 대해서 층상실리케이트의 층간사이 간격의 변화는 반비례하는 특성을 나타내었고, 충진함량이 증가됨에따라 자체만으로는 크게 응집된 입자의 분산이 미약한 결과로 볼 수 있다. 그러나 Homogenizer와 동시에 분산할 때는 충진함량이 크게 증가하여도 균질한 분산이 이루어졌다.

• Korea-Australia Rheology Journal
• /
• v.18 no.3
• /
• pp.153-160
• /
• 2006

We analyzed the non-Newtonian and non-isothermal flow with Carreau-Yasuda viscosity model in co-rotating and counter-rotating twin screw extruder systems. The mixing performances with respect to the screw speed, the screw pitch, and the rotating direction have been investigated. The dynamics of mixing was studied numerically by tracking the motions of particles. The extent of mixing was characterized in terms of the deformation rate, the residence time distribution, and the average strain. The results showed that the high screw speed decreases the residence time but increases the deformation rate. Small screw pitch increases the residence time. It is concluded that the high screw speed increases the dispersive mixing performance, while the small screw pitch increases the distributive mixing performance. Co-rotating screw extruder has the better conveying performance and the distributive mixing performance than counter-rotating screw extruder with the same screw speed and pitch. Co-rotating screw extruder developed faster transport velocity and it is advantageous the flow characteristics to the mixing that transfers polymer melt from one barrel to the other barrel.