• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.527-534
• /
• 2012

The adsorption dynamics of activated carbon (AC) and carbon molecular sieve (CMS) beds were studied to recover ethylene from FCC fuel gas. In this study, the FCC fuel gas used consisted of six-component mixture ($CH_4/C_2H_4/C_2H_6/C_3H_6/N_2/H_2$,32:15:14:2:12:25 vol.%). And the breakthrough experiments of adsorption and desorption were carried out. The breakthrough sequence in the AC bed was $H_2$ < $N_2$ < $CH_4$ < $C_2H_4$ < $C_2H_6$ while the sequence in the CMS bed was $H_2$ < $CH_4$ < $N_2$ < $C_2H_6$ < $C_2H_4$. The separation performance of the CMS bed during the adsorption step was lower than that of the AC bed. However, due to the characteristics of kinetic separation, the CMS bed could remove $CH_4/N_2$ as well asthe molecules that are larger than $C_2H_6$, which was not easy to be done by the AC bed. Since it was hard to regenerate the adsorption bed by simple depressurization, vacuum regeneration should be adopted. As a result, the pressure vacuum swing adsorption (PVSA) process, consisting of CMS pretreatment process and AC main process, was suggested to recover ethylene efficiently.

• Carbon letters
• /
• v.10 no.2
• /
• pp.114-122
• /
• 2009

Crushed, depitted peach stones were impregnated activated with 50% $H_3PO_4$ followed by pyrolysis at $500^{\circ}C$. Two activated carbons were produced, one under its own evolved gases during pyrolysis, and the second conducted with air flow throughout the carbonization stage. Physicochemical properties were investigated by several procedures; carbon yield, ash content, elemental chemical analysis, TG/DTG and FTIR spectra. Porosity characteristics were determined by the conventional $N_2$ adsorption at 77 K, and data analyzed to get the major texture parameters of surface area and pore volume. Highly developed activated carbons were obtained, essentially microporous, with slight effect of air on the porous structure. Oxygen was observed to be markedly incorporated in the carbon matrix during the air treatment process. Cation exchange capacity towards Cu (II) and Cd (II) was tested in batch single ion experimental mode, which proved to be slow and a function of carbon dose, time and initial ion concentration. Copper was up taken more favorably than cadmium, under same conditions, and adsorption of both cations was remarkably enhanced as a consequence of the air treatment procedure. Sequestration of the metal ions was explained on basis of the combined effect of the oxygen functional groups and the phosphorous-containing compounds; both contributing to the total surface acidity character.

• Carbon letters
• /
• v.2 no.1
• /
• pp.15-21
• /
• 2001

In this work, activated carbon fibers (ACFs) were plated with copper metal using electroless plating method and the effects of surface properties and pore structures on chromium adsorption properties were investigated. Surface properties of ACFs have been characterized using pH and acid/base values. BET data with $N_2$ adsorption were used to obtain the structural parameters of ACFs. The electroless copper plating did significantly lead to a decrease in the surface acidity or to an increase in the surface basicity of ACFs. However, all of the samples possessed a well-developed micropore. The adsorption capacity of Cr(III) for the electroless Cu-plated ACFs was higher than that of the as-received, whereas the adsorption capacity of Cr(VI) for the former was lower than that of the latter. The adsorption rate constants ($K_1$, $K_2$, and $K_3$) were also evaluated from chromium adsorption isotherms. It was found that $K_1$ constant for Cr(III) adsorption depended largely on surface basicity. The increase of Cr(III) adsorption and the decrease of Cr(VI) adsorption were attributed to the formation of metal oxides on ACFs, resulting in increasing the surface basicity.

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2003.11a
• /
• pp.158-161
• /
• 2003

To develop an effective adsorbent for radio active Carbon Dioxide, $^14CO_2$, which is discharged to nearby atmosphere from nuclear power plants of CANDU type, we made some preliminary adsorbents and tested their abilities of $CO_2$ removal. The chemical agents used was LiOH and we supported or impregnated it on the surface or the internal volume of activated Carbon(GW-H). The physical and chemical properties of various adsorbents were measured using methods such as XRD, BET. SEM images were taken to investigate the change of surface morphology of the adsorbents. Finally, amount of $CO_2$ adsorption of them were verified under specific conditions. We found that mechanical mixing of LiOH and activated Carbon showed the maximum $CO_2$ removal ability, while surface activation of activated Carbon by Nitric Acid-treatment enhanced its $CO_2$ removal efficiency to some degree.

• Carbon letters
• /
• v.15 no.1
• /
• pp.45-49
• /
• 2014

In this study, synthetic viscose rayon fabric has been used for preparing activated carbon fabric (ACF), impregnated with different concentrations of $H_3PO_4$. The effect of $H_3PO_4$ impregnation on the weight yield, surface area, pore volume, chemical composition and morphology of ACF were studied. Experimental results revealed that both Brunauer-Emmett-Teller surface area and micropore volume increased with increasing $H_3PO_4$ concentration; however, the weight yield and microporosity (%) decreased. It was observed that samples impregnated at $70^{\circ}C$ (AC-70) give higher yield and higher microporosity as compared to $30^{\circ}C$ (AC-30). The average pore size of the ACF also gradually increases from 18.2 to 19 and 16.7 to $20.4{\AA}$ for $30^{\circ}C$ and $70^{\circ}C$, respectively. The pore size distribution of ACF was also studied. It is also concluded that the final ACF strength is dependent on the concentration of impregnant.

• Environmental Engineering Research
• /
• v.12 no.1
• /
• pp.1-7
• /
• 2007

Most of the herb residue producing from oriental medical clinics(OMC) and hospitals(OMH) is wasted in Korea. To develop of adsorbent for removing heavy metal from wastewater, the various pre-treatment methods of the herb residue were evaluated by potentiometric titration, Freundlich isotherm adsorption test and the kinetic adsorption test. The herb residue was pre-treated for increasing the adsorption capacity by cleaning with distilled water, 0.1 N HCl and 0.1 N NaOH and by heating at $370^{\circ}C$ for 30 min. It showed a typical weak acid-weak base titration curve and a short pH break like commercial activated carbon during photentiometric titration of pre-treated herb residue. The log-log plots in the Freundlich isotherm test were linear on the herb residue pre-treated with NaOH or HCl like commercial activated carbon. The adsorption capacity(qe) in the Freundlich isotherm test for $Cr^{6+}$ was 1.5 times higher in the pre-treated herb residue with HCl than in activated carbon. On the other hand the herb residue pre-treated with NaOH showed the good adsorption capacities for $Pb^{2+}$, $Cu^{2+}$ and $Cd^{2+}$ even though those adsorption capacities were lower than that of activated carbon. In kinetic test, most of heavy metals removed within the first 10 min of contact and then approached to equilibrium with increasing contact time. The removal rate of heavy metals increased with an increase of the amount of adsorbent. Likewise, the removal rates of heavy metals were higher in the herb residue pre-treated with NaOH than in that pre-treated with HCl. The adsorption preference of herb residues pre-treated with NaOH or HCl was $Pb^{2+}>Cu^{2+}$ or $Cd^{2+}>Cr^{6+}$ in the order. Conclusively, the herb residue can be used as an alternative adsorbent for the removal of heavy metals depending on pr-treatment methods.

• Korean Chemical Engineering Research
• /
• v.53 no.1
• /
• pp.64-70
• /
• 2015

Batch experiment studies were carried out for adsorption of congo red using granular activated carbon with various parameters such as activated carbon dose, pH, initial dye concentration, temperature and contact time. Equilibrium experimental data are fitted to the Langmuir, Freundlich, Temkin and Dubin-Radushkevich isotherm equations. From Freundlich's separation factor (1/n) estimated, adsorption could be employed as effective treatment method for adsorption of congo red from aqueous solution. Base on Temkin constant (B) and Dubinin-Radushkevich constant (E), this adsorption process is physical adsorption. Adsorption kinetics has been tested using pseudo-first order and pseudo second order models. The results followed pseudo second order model with good correlation. Adsorption process of congo red on granular activated carbon was endothermic (${\Delta}H$=42.036 kJ/mol) and was accompanied by decrease in Gibbs free energy (${\Delta}G$=-2.414 to -4.596 kJ/mol) with increasing adsorption temperature.

• Clean Technology
• /
• v.26 no.2
• /
• pp.122-130
• /
• 2020

The isotherm, kinetic, and thermodynamic parameters of reactive blue 4 adsorbed by activated carbon were investigated for activated carbon dose, pH, initial concentration, contact time, and temperature data. The adsorption of the RB 4 dye by activated carbon showed a concave shape in which the percentage of adsorption increased in both directions starting from pH 7. The isothermal adsorption data were applied to Langmuir, Freundlich, and Temkin isotherms. Both Freundlich and Langmuir isothermal adsorption models fit well. From determined Freundlich separation factor (1/n = 0.125 ~ 0.232) and Langmuir separation factor (R_L = 1.53 ~ 1.59), adsorption of RB 4 by activated carbon could be employed as an effective treatment method. The constant related to the adsorption heat (B_T = 2.147 ~ 2.562 J mol^-1) of Temkin showed that this process was physical adsorption. From kinetic experiments, the adsorption process followed the pseudo second order model with good agreement. The results of the intraparticle diffusion model showed that the inclination of the first straight line representing the surface diffusion was smaller than that of the second straight line representing the intraparticle pore diffusion. Therefore, it was confirmed that intraparticle pore diffusion is the rate-controlling step. The negative Gibbs free energy change (ΔG = -3.262 ~ -7.581 kJ mol^-1) and the positive enthalpy change (ΔH = 61.08 kJ mol^-1) indicated the spontaneous and endothermic nature of the adsorption process, proving this process to be spontaneous and endothermic.

• Clean Technology
• /
• v.27 no.3
• /
• pp.261-268
• /
• 2021

Equilibrium, kinetics, and thermodynamics of adsorption of acid black 1 (AB1) by coal-based granular activated carbon (CGAC) were investigated with the adsorption variables of initial concentration of dye, contact time, temperature, and pH. The adsorption reaction of AB1 by activated carbon was caused by electrostatic attraction between the surface (H⁺) of activated carbon and the sulfite ions (SO₃^-) and nitrite ions (NO₂^-) possessed by AB1, and the degree of reaction was highest at pH 3 (97.7%). The isothermal data of AB1 were best fitted with Freundlich isotherm model. From the calculated separation factor (1/n) of Freundlich, it was confirmed that adsorption of AB1 by activated carbon could be very effective. The heat of adsorption in the Temkin model suggested a physical adsorption process (< 20 J mol^-1). The kinetic experiment favored the pseudo second order model, and the equilibrium adsorption amount estimated from the model agreed to that given by the experiments (error < 9.73% ). Intraparticle diffusion was a rate controlling step in this adsorption process. From the activation energy and enthalpy change, it was confirmed that the adsorption reaction is an endothermic reaction proceeding with physical adsorption. The entropy change was positive because of an active reaction at the solid-liquid interface during adsorption of AB1 on the activated carbon surface. The free energy change indicated that the spontaneity of the adsorption reaction increased as the temperature increased.

• Proceedings of the KIEE Conference
• /
• 1998.11c
• /
• pp.856-857
• /
• 1998

Hydrogenated amorphous carbon nitride [a-C:H(N)] films were deposited on pretreated silicon(100) substrate in activated gas phase using. RF plasma-assisted CVD. We measured the FT-IR spectrum to investigate $C{\equiv}N$ stretching mode(nitrile), C-H stretching mode, C-H bending mode, C=C stretching mode C=N(imino) mode, and the EDX to investigate the ratio of N to C(0.25). By the results of FT-IR and EDX spectrum, We confirmed that hydrogenated amorphous carbon nitride films successfully were synthesized by RF-PACVD