• Fire Science and Engineering
• /
• v.25 no.3
• /
• pp.113-118
• /
• 2011

The flash point is an important indicator of the flammability of a chemical. The minimum flash point behaviour (MFPB) is exhibited when the flash point of a mixture is below the flash points of the individual components. The identification of this behaviour is critical, because a hazardous situation results from taking the lowest component flash point value as the mixture flash point. In this study, the flash points for the n-butanol + n-decane and n-octane + n-propanol systems which exhibit MFPB, were measured by Tag open-cup apparatus. The experimental data were compared with the alues calculated by the Raoult's law, the van Laar equation and the Wilson equation. The calculated values based on the van Laar and Wilson equations were found to be better than those based on the Raoult's law. It was concluded that the van Laar and Wilson equations were more effective than the Raoult' law at describing the activity coefficients for non-ideal solution such as the n-butanol + n-decane and n-octane + n-propanol systems. The predictive curve of the flash point prediction model based on the Wilson equation described the experimentally-derived data more effectively than was the case when the prediction model was based upon the van Laar equation.

• Applied Chemistry for Engineering
• /
• v.20 no.1
• /
• pp.15-20
• /
• 2009

In this study, solubilization experiments of n-octane oil were performed by micellar solutions of polymeric nonionic surfactant Pluronic L64 ($EO_{13}PO_{30}EO_{13}$) at room temperature. A single spherical drop of n-octane was injected into aqueous surfactant solution using an oil drop contacting technique and solubilization rate of n-octane was measured by observing the size of oil drop with time. It was found that solubilization rate was independent of initial oil drop size but inversely proportional to the initial surfactant concentration. These results revealed that solubilization of n-octane oil by L64 micellar solution is controlled by interface-controlled mechanism rather than diffusion-controlled mechanism. Dynamic interfacial tension measurements showed that interfacial tension decreases such as from $2.59{\times}10^{-2}$ to $2.45{\times}10^{-2}$, and further to $2.13{\times}10^{-2}mN/m$ as surfactant concentration increases from 8 to 9 and further to 10 wt% respectively. The equilibration time was also found to decrease slightly with an increase in surfactant concentration. All three systems reached an equilibrium within 7 minutes.

• Journal of the Korean Society of Combustion
• /
• v.17 no.2
• /
• pp.9-16
• /
• 2012

Iso-octane, n-heptane and their blends were tested in a constant volume combustion chamber to measure laminar flame speeds. The experimental apparatus was automatically controlled to enhance the accuracy and data acquisition speed. A large database of laminar flame speeds at elevated temperatures and pressures was established. From this database, laminar flame speeds of iso-octane, n-heptane and their blends were investigated and analysed to derive new correlation to predict laminar flame speeds at any blending ratio. The new flame speed model was successfully applied to these fuels with limited range of errors.

• Membrane and Water Treatment
• /
• v.10 no.5
• /
• pp.361-372
• /
• 2019

Effect of different alkane based solvents on the stability of emulsion liquid membrane was investigated using normal alkanes (n-hexane, n-heptane, n-octane and n-decane) under various operating parameters of surfactant concentration, emulsification time, internal phase concentration, volume ratio of internal phase to organic phase, volume ratio of emulsion phase to external phase and stirring speed. Results of stability revealed that emulsion liquid membrane containing n-octane as solvent and span-80 (5 % (w/w)) as emulsifying agent presented the highest amount of emulsion stability (the lowest breakage) compared with other solvents; however, operating parameters (surfactant concentration (5% (w/w)), emulsification time (6 min), internal phase concentration (0.05 M), volume ratio of internal phase to organic phase (1/1), volume ratio of emulsion phase to external phase (1/5) and stirring speed (300 rpm)) were also influential on improving the stability (about 0.2% breakage) and on achieving the most stable emulsion. The membrane with the highest stability was employed to extract acridine orange with various concentrations (10, 20 and 40 ppm) from water. The emulsion liquid membrane prepared with n-octane as the best solvent almost removed 99.5% of acridine orange from water. Also, the prepared liquid membrane eliminated completely (100%) other cationic dyes (methylene blue, methyl violet and crystal violet) from water demonstrating the efficacy of prepared emulsion liquid membrane in treatment of dye polluted waters.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.1
• /
• pp.10-17
• /
• 2008

This study has been focused on the partial oxidation(POX) of n-octane over Rh-containing catalysts supported on alumina. The catalysts for this reaction were prepared by incipient wetness(IW) and co-gel(CG) methods, followed by the calcination at $900{\circ}C$ or $1,200{\circ}C$. When applied to the POX of n-octane carried out at $600{\circ}C$ with C/O=3 and GHSV=3,450/h, the catalyst prepared by the CG method and calcined at $1,200{\circ}C$ showed the best activity, yielding 42% syngas($H_2$+CO) with the $H_2$/CO ratio of $2{\sim}2.4$. To enhance the activity and stability of catalysts, bimetallic catalysts were synthesized by the CG method. As a result, the performance of Rh-Ni/$Al_2O_3$ catalyst was superior to that of Rh/$Al_2O_3$ catalyst in terms of the catalyst stability, due to the retarding effect on the Rh-to-$Rh_2O_3$ transition by the addition of Ni. This result was confirmed by XRD, TEM, and TPR characterizations.

• Journal of ILASS-Korea
• /
• v.16 no.4
• /
• pp.167-175
• /
• 2011

The HCCI engines have been known with high efficiency and low pollution and can be actualized as the new internal combustion engines. However, As for(??) the ignition and combustion depend strongly on the oxidation reaction of the fuel, so it is difficult to control auto-ignition timing and combustion duration. Purpose of this paper is creating the database for development of multi-dimensional simulation and investigating the influence of different molecular structure. In this research, the effect of n-heptane mole ratio in fuel (XnH) on the ignition delay from homogeneous charge compression ignition(HCCI) has been investigated experimentally. By varying the XnH, it was possible to ascertain whether or not XnH is the main resource of ignition delay. Additionally, the information on equivalence ratio for varying XnH was obtained. The tests were performed on a RCM (Rapid Compression Machine) fueled with n-heptane and iso-octane. The results showed that decreasing XnH (100, 30, 20, 10,0), the ignition delays of low temperature reaction (tL) and high temperature reaction (tH) is longer. And the temperature of reaction increases by about 30K. n-heptane partial equivalence ratio (fnH) affect on tL.and TL. When ${\phi}$nH was increased as a certain value, tL was decreased and TL was increased.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.3
• /
• pp.13-19
• /
• 2003

Mathematically simplified reaction scheme that simulates autoignitions of the end gases in spark ignition engines has been studied computationally. The five equation model is described, to predict the essential features of hydrocarbon oxidation. This scheme has been calibrated against autoignition delay times measured in rapid compression machines. The rate constants, activation temperatures, Ta, Arrhenius preexponential constants, A, and heats of reaction for stoichiometric n-heptane/air, iso-octane/air, and their mixtures have all been optimised. The optimisation has been guided by Morley's correlation of the ratio of chain branching to linear termination rates with octane number. Comparisons between computed and experimental autoignition delay times have validated the Present simplified reaction scheme and the influences of octane number upon autoignition delay times have been computationally investigated. It has been found that both cool flame and high temperature direct reactions can have an effect on autoignition delay times.

• Korean Chemical Engineering Research
• /
• v.46 no.2
• /
• pp.291-300
• /
• 2008

Catalytic cracking of n-octane was carried out over H-ZSM-5 zeolite catalysts after calcination with air and steaming with 100% steam in the temperature range of $550-750^{\circ}C$ for 24 h and compared with the results of thermal cracking. The increase of calcination and steaming temperature resulted in the decrease of surface area, pore volume, and strong acid sites, which was mainly caused by the dealumination of H-ZSM-5 framework. It was found by $^{27}Al$ and $^{29}Si$ MAS NMR that the dealumination was proceeded through the transformation process of tetrahedral framework Al${\rightarrow}$penta-cordinated Al ${\rightarrow}$ octahedral framework Al and the phenomena was much more severe in steaming conditions than that of calcination. In the catalytic cracking of n-octane, as the temperatures of calcination and steaming were increased, the conversion of n-octane, the selectivity of light olefins and ethylene to propylene ratio were decreased due to the dealumination of framework aluminum resulting the loss of acidic strengths. The conversion, selectivity of light olefins and ethylene to propylene ratio reached almost to the level of thermal cracking after steaming at $750^{\circ}C$ for 24 h.

• Korean Journal of Microbiology
• /
• v.28 no.1
• /
• pp.71-75
• /
• 1990

The isolates biodigrading crude oil were examined to characterize thier properties. Isolates which were identified as Acinetobacter lwoffii G1, Klebsiella pneumoniae L25, Pseudomonas maltophilia N246, Xanthomonas campestris M12, and Xanthomonas sp. M28. The optimum concentration of crude oil was 0.15% for the bacterial growth. X. campestris M12, Xanthomonas sp. M28, and K. penumoniae L25 showed the maximal growth at the concentration of 3.5% sodium chloride, indicating that they were derived from sea water. Among the isolates, X. campestris M12, Xanthomonas sp. M28 specially utilized hexadecane and octane, and P. maltophilia N246 utilized octane with optimum concentration of 0.2-0.3% as sole carbon source. The utilization of components of saturate fraction by K. pneumoniae L25 was examined by gas-liquid chromatography. The short-chain saturates are used before the long chain ones although they almost disappear within 8 days of incubation at $30^{\circ}C$.

• Elastomers and Composites
• /
• v.38 no.1
• /
• pp.51-56
• /
• 2003

Cloud-point and bubble-point data to $170^{\circ}C$ and 50 bar are presented for four different solvents, normal pentane. n-hexane, n-heptane, and n-octane with poly(ethylene-co-42 wt% octene) ($PEO_{42}$) copolymer. The pressure-concentration isotherms measured for $PEO_{42}$ - normal pentane have maximums at around 5 wt% of the copolymer concentrations in the solution. $PEO_{42}$- normal pentane system exhibits LCST-type phase behavior at temperatures greater than $130^{\circ}C$. Below $120^{\circ}C$, bubble-point type transitions are observed. However, the binary mixtures for $PEO_{42}$ in n-hexane, n-heptane, and n-octane have only bubble-point type transitions at the pressure-temperature region investigated in this study. The single-phase region of PEO - alkane mixtures increases with the molecular size of alkane solvent due to the increasing dispersion interactions between PEO and the alkane.