• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제17권5호
• /
• pp.541-544
• /
• 2004

Multi- wall carbon nanotubes(MWNTs) were synthesized by thermal chemical vapor deposition. The paste for screen printing was composed of MWNTs, organic vehicle and glass frit. Carton nanotube paste was screen-printed on ITO(indium tin oxide) deposited soda lim을 glass, and then heat treatment was performed. Before the surface treatment, turn on field of derive was 2.6 V/$\mu\textrm{m}$. After the surface treatment, the value was changed into 1.8 V/$\mu\textrm{m}$. The anode current of the derive with 2.83 V/$\mu\textrm{m}$(turn on field) was changed 4 $\mu\textrm{A}$ into 390 $\mu\textrm{A}$ at 1,700 V. Adsorption effect of MWNTs onto phosphor of anode plate was observed by the field emission measurement and resulted in bad effects on properties of devices lifetime and emission lighting.

• Proceedings of the Korean Vacuum Society Conference
• /
• 한국진공학회 2000년도 제18회 학술발표회 논문개요집
• /
• pp.210-210
• /
• 2000

Vertically well aligned multi-wall carbon nanotubes (CNT) were grown on nickel coated glass substrates by plasma enhanced hot filament chemical vapor deposition at low temperatures below 600$^{\circ}C$. Acetylene and ammonia gas were used as the carbon source and a catalyst. Effects of growth parameters such as pre-treatment of substrate, plasma intensity, filament current, imput gas flow rate, gas composition, substrate temperature and different substrates on the growth characteristics of CNT were systematically investigated. Figure 1 shows SEM image of CNT grown on Ni coated glass substrate. Diameter of nanotube was 30 to 100nm depending on the growth condition. The diameter of CNT decreased and density of CNT increased as NH3 etching time etching time increased. Plasma intensity was found to be the most critical parameter to determine the growth of CNT. CNT was not grown at the plasma intensity lower than 500V. Growth of CNT without filament current was observed. Raman spectroscopy showed the C-C tangential stretching mode at 1592 cm1 as well as D line at 1366 cm-1. From the microanalysis using HRTEM, nickel cap was observed on the top of the grown CNT and very thin carbon amorphous layer of 5nm was found on the nickel cap. Current-voltage characteristics using STM showed about 34nA of current at the applied voltage of 1 volt. Electron emission from the vertically well aligned CNT was obtained using phosphor anode with onset electric field of 1.5C/um.

• Journal of the Semiconductor & Display Technology
• /
• 제4권3호
• /
• pp.11-15
• /
• 2005

This paper shows that carbon nanotubes can be applied to a nanopipette. Nano space in atomic force microscope multi wall carbon nanotube tips is filled with molecules and atoms with charges and then, the tips can be applied to nanopipette when the encapsulated media flow off under applying electrostatic farces. Since the nano space inside the tips can be refilled, the tips can be permanently used in ideal conditions of no chemical reaction and no mechanical deformation. Molecular dynamics simulations for nanopipette applications demonstrated the possibility of nano-lithography or single-metallofullerene-transistor array fabrication.

• Korean Journal of Materials Research
• /
• 제20권10호
• /
• pp.513-517
• /
• 2010

There have been many efforts to modify and improve the properties of functional thin films by hybridization with nano-sized materials. For the fabrication of electronic circuits, micro-patterning is a commonly used process. For photochemical metal-organic deposition, photoresist and dry etching are not necessary for microscale patterning. We obtained direct-patternable $SnO_2$ thin films using a photosensitive solution containing Ag nanoparticles and/or multi-wall carbon nanotubes (MWNTs). The optical transmittance of direct-patternable $SnO_2$ thin films decreased with introduction of nanomaterials due to optical absorption and optical scattering by Ag nanoparticles and MWNTs, respectively. The crystallinity of the $SnO_2$ thin films was not much affected by an incorporation of Ag nanoparticles and MWNTs. In the case of mixed incorporation with Ag nanoparticles and MWNTs, the sheet resistance of $SnO_2$ thin films decreased relative to incorporation of either single component. Valence band spectral analyses of the nano-hybridized $SnO_2$ thin films showed a relation between band structural change and electrical resistance. Direct-patterning of $SnO_2$ hybrid films with a line-width of 30 ${\mu}m$ was successfully performed without photoresist or dry etching. These results suggest that a micro-patterned system can be simply fabricated, and the electrical properties of $SnO_2$ films can be improved by incorporating Ag nanoparticles and MWNTs.

• Macromolecular Research
• /
• 제10권5호
• /
• pp.253-258
• /
• 2002

The multi-wall carbon nanotubes (MWNTs) with graphite crystal structure were synthesized by the catalytic decomposition of a ferrocene-xylene mixture in a quartz tube reactor to use as the conductive filler in the binary polymer matrix composed of poly(vinylidene fluoride) (PVdF) and poly(vinyl pyrrolidone) (PVP) for the EMI (electromagnetic interference) shielding applications. The yield of MWNTS was significantly dependent on the reaction temperature and the mole ratio of ferrocene to xylene, approaching to the maximum at 800 $^{\circ}C$ and 0.065 mole ratio. The electrical conductivity of the MWNTs-filled PVdF/PVP composite proportionally depended on the mass ratio of MWNTs to the binary polymer matrix, enhancing significantly from 0.56 to 26.7 S/cm with the raise of the mass ratio of MWNTs from 0.1 to 0.4. Based on the higher electrical conductivity and better EMI shielding effectiveness than the carbon nanofibers (CNFs)-filled coating materials, the MWNTs-filled binary polymer matrix showed a prospective possibility to apply to the EMI shielding materials. Moreover, the good adhesive strength confirmed that the binary polymer matrix could be used for improving the plastic properties of the EMI shielding materials.

• Journal of the Microelectronics and Packaging Society
• /
• 제26권4호
• /
• pp.107-111
• /
• 2019

We report the fabrication of a CdS/CuInGaSe (CdS/CIGS) structure with carbon nanotubes and its application as a photocathode for photoelectrochemical water splitting. CIGS thin films were fabricated using co-evaporation by RF magnetron sputtering, while CdS was fabricated by chemical bath deposition. Spray coated multi-wall carbon nanotube (CNT) film on CdS/CIGS thin film was investigated as a photocathode. The CNT-coated CdS/CIGS showed superior photocurrent density and exhibited improved photostability.

• Composites Research
• /
• 제30권1호
• /
• pp.7-14
• /
• 2017

In this paper, the inter-lamina shear strength (ILSS) of multi-wall carbon nanotube (MWNT) reinforced carbon fiber reinforced plastics (CFRP) and thin-ply composites were verified under low earth orbit (LEO) space environment. CFRP, MWNT reinforced CFRP, thin-ply CFRP and MWNT reinforced thin-ply CFRP were tested after aging by using accelerated ground simulation equipment. The used ground simulation equipment can simulate high vacuum ($2.5{\times}10^{-6}torr$), atomic oxygen (AO, $9.15{\times}10^{14}atoms/cm^2{\cdot}s$), ultraviolet light (UV, 200 nm wave length) and thermal cycling ($-70{\sim}100^{\circ}C$) simultaneously. The duration of aging experiment was twenty hours, which is an equivalent duration to that of STS-4 space shuttle condition. After the aging experiment, ILSS were measured at room temperature ($27^{\circ}C$), high temperature ($100^{\circ}C$) and low temperature ($-100^{\circ}C$) to verify the effect of operation temperature. The MWNT and thin-ply shows good improvement of ILSS at ground condition especially with the thin-ply. And after LEO exposure large degradation of ILSS was observed at MWNT added composite due to the thermal cycle. And the degradation rate was much higher under the high temperature condition. But, at the low temperature condition, the ILSS was largely recovered due to the matrix toughening effect.

• Proceedings of the Polymer Society of Korea Conference
• /
• 한국고분자학회 2006년도 IUPAC International Symposium on Advanced Polymers for Emerging Technologies
• /
• pp.288-288
• /
• 2006

Natural rubbers (NR) reinforced by multi-wall carbon nanotubes (MWCNT) was found to show extraordinary improvement of mechanical property. We speculated that this was owing to the interfacial phase that surrounded CNT and investigated about the phase by atomic force microscopy (AFM). Using force modulation mode and force-distance curve analyses, we succeeded in obtaining the information of its nanometer-scale rheological property. We found that was actually surrounded by the interfacial phase, that had softer modulus than NR matrix.

• Electrical & Electronic Materials
• /
• 제12권7호
• /
• pp.7-11
• /
• 1999

Fully sealed field emission display in size of 4.5 inch has been fabricated using single-wall carbon nanotubes-organic vehicle com-posite. The fabricated display were fully scalable at low temperature below 415$^{\circ}C$ and CNTs were vertically aligned using paste squeeze and surface rubbing techniques. The turn-on fields of 1V/${\mu}{\textrm}{m}$ and field emis-sion current of 1.5mA at 3V/${\mu}{\textrm}{m}$ (J=90${\mu}{\textrm}{m}$/$\textrm{cm}^2$)were observed. Brightness of 1800cd/$m^2$ at 3.7V/${\mu}{\textrm}{m}$ was observed on the entire area of 4.5-inch panel from the green phosphor-ITO glass. The fluctuation of the current was found to be about 7% over a 4.5-inch cath-ode area. This reliable result enables us to produce large area full-color flat panel dis-play in the near future. Carbon nanotubes (CNTs) have attracted much attention because of their unique elec-trical properties and their potential applica-tions [1, 2]. Large aspect ratio of CNTs together with high chemical stability. ther-mal conductivity, and high mechanical strength are advantageous for applications to the field emitter [3]. Several results have been reported on the field emissions from multi-walled nanotubes (MWNTs) and single-walled nanotubes (SWNTs) grown from arc discharge [4, 5]. De Heer et al. have reported the field emission from nan-otubes aligned by the suspension-filtering method. This approach is too difficult to be fully adopted in integration process. Recently, there have been efforts to make applications to field emission devices using nanotubes. Saito et al. demonstrated a car-bon nanotube-based lamp, which was oper-ated at high voltage (10KV) [8]. Aproto-type diode structure was tested by the size of 100mm $\times$ 10mm in vacuum chamber [9]. the difficulties arise from the arrangement of vertically aligned nanotubes after the growth. Recently vertically aligned carbon nanotubes have been synthesized using plasma-enhanced chemical vapor deposition(CVD) [6, 7]. Yet, control of a large area synthesis is still not easily accessible with such approaches. Here we report integra-tion processes of fully sealed 4.5-inch CNT-field emission displays (FEDs). Low turn-on voltage with high brightness, and stabili-ty clearly demonstrate the potential applica-bility of carbon nanotubes to full color dis-plays in near future. For flat panel display in a large area, car-bon nanotubes-based field emitters were fabricated by using nanotubes-organic vehi-cles. The purified SWNTs, which were syn-thesized by dc arc discharge, were dispersed in iso propyl alcohol, and then mixed with on organic binder. The paste of well-dis-persed carbon nanotubes was squeezed onto the metal-patterned sodalime glass throuhg the metal mesh of 20${\mu}{\textrm}{m}$ in size and subse-quently heat-treated in order to remove the organic binder. The insulating spacers in thickness of 200${\mu}{\textrm}{m}$ are inserted between the lower and upper glasses. The Y\ulcornerO\ulcornerS:Eu, ZnS:Cu, Al, and ZnS:Ag, Cl, phosphors are electrically deposited on the upper glass for red, green, and blue colors, respectively. The typical sizes of each phosphor are 2~3 micron. The assembled structure was sealed in an atmosphere of highly purified Ar gas by means of a glass frit. The display plate was evacuated down to the pressure level of 1$\times$10\ulcorner Torr. Three non-evaporable getters of Ti-Zr-V-Fe were activated during the final heat-exhausting procedure. Finally, the active area of 4.5-inch panel with fully sealed carbon nanotubes was pro-duced. Emission currents were character-ized by the DC-mode and pulse-modulating mode at the voltage up to 800 volts. The brightness of field emission was measured by the Luminance calorimeter (BM-7, Topcon).

• Carbon letters
• /
• 제24권
• /
• pp.103-110
• /
• 2017

Carbon-based magnetic nanostructures in several instances have resulted in improved physicochemical and catalytic properties when compared to multi-wall carbon nanotubes (MWCNTs) and magnetic nanoparticles. In this study, magnetic MWCNTs with a structure of $Ni_xZn_xFe_2O_4/MWCNT$ as peroxidase mimics were fabricated by the one-pot hydrothermal method. The structure, composition and morphology of the nanocomposites were characterized with X-ray diffraction (XRD), Fourier transform infrared spectroscopy and transmission electron microscopy. The magnetic properties were investigated with a vibrating sample magnetometer. The peroxidase-like catalytic activity of the nanocomposites was investigated by colorimetric and electrochemical tests with 3,3',5,5'-tetramethylbenzidine (TMB) and $H_2O_2$ as the substrates. The results show that the synthesis of the nanocomposites was successfully performed. XRD analysis confirmed the crystalline structures of the $Ni_xZn_xFe_2O_4/MWCNT$ nanohybrids and MWCNTs. The main peaks of the $Ni_xZn_xFe_2O_4/MWCNT$s crystals were presented. The $Ni_{0.25}Zn_{0.25}Fe_2O_4/MWCNT$ and $Ni_{0.5}Zn_{0.5}Fe_2O_4/MWCNT$ nanocatalysts showed nearly similar physicochemical properties, but the $Ni_{0.5}Zn_{0.5}Fe_2O_4/MWCNT$ nanocatalyst was more appropriate than the $Ni_{0.25}Zn_{0.25}Fe_2O_4/MWCNT$ nanocatalyst in terms of the magnetic properties and catalytic activity. The optimum peroxidase-like activity of the nanocatalysts was obtained at pH 3.0. The $Ni_{0.5}Zn_{0.5}Fe_2O_4/MWCNT$ nanocatalyst exhibited a good peroxidase-like activity. These magnetic nanocatalysts can be suitable candidates for future enzyme-based applications such as the detection of glucose and $H_2O_2$.