• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.266-276
• /
• 2018

This paper presents a new step-up and step-down multi-pulse auto-transformer rectifier unit (ATRU) topology. This structure can achieve a wide range of output voltages, which solves the problem of auto-transformer output voltage being difficult to regulate. Adding middle taps to the primary winding and reasonably setting the number of auto-transformer windings, constituted two groups of three-phase output voltages with a $30^{\circ}$ phase difference. Multi-pulse output DC voltage is obtained after a three-phase output voltage across two rectifier bridges and inter-phase reactor. Thus, the output DC voltage is related to the number and configuration of the auto-transformer winding. In this paper, the relationship between the voltage ratio of the auto-transformer and the ratio of winding, input current and auto-transformer kilovoltampere rating are deduced and validated by simulations. On this basis, the output voltage range is optimized. An experiment on two different voltage ratio principle prototypes was carried out to verify the correctness of the analysis design.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2008.04a
• /
• pp.20-25
• /
• 2008

The finite element analysis for porous media is severe job because constituents have different physical peoperties, and element's continuity and stability should be considered. Thus, we propose the new mixed finite element method in order to overcome the problems. In this method, multi time step, remeshing step, and sub iteration step are introduced. The multi time step and remeshing step make it possible to satisfy a stability and an accuracy during sub iteration in which global time is determined. Finally, the proposed method is compared with the ABAQUS(2007) software and exact solution(Schiffman 1967) through two dimensional consolidation model.

• Nuclear Engineering and Technology
• /
• v.54 no.5
• /
• pp.1789-1803
• /
• 2022

RAST-F is a new full-core analysis code based on the two-step approach that couples a multi-group cross-section generation Monte-Carlo code MCS and a multi-group nodal diffusion solver. To demonstrate the feasibility of using MCS/RAST-F for fast reactor analysis, this paper presents the coupled nodal code verification results for the MET-1000 and CAR-3600 benchmark cores. Three different multi-group cross-section calculation schemes are employed to improve the agreement between the nodal and reference solutions. The reference solution is obtained by the MCS code using continuous-energy nuclear data. Additionally, the MCS/RAST-F nodal solution is verified with results based on cross-section generated by collision probability code TULIP. A good agreement between MCS/RAST-F and reference solution is observed with less than 120 pcm discrepancy in k_eff and less than 1.2% root-mean-square error in power distribution. This study confirms the two-step approach MCS/RAST-F as a reliable tool for the three-dimensional simulation of reactor cores with fast spectrum.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.149-157
• /
• 1994

In this study two dimensional visco-plastic finite element model capable of handling the multi-step excavation was developed for investigating the effect of excavation support sequences on the behavior of underground openings in the jointed rock mass. First, the finite element model which is capable of handling the multi-step excavation is developed and verified. And then the model is combined with visco-plastic joint model. Ubiquitous joint pattern was considered in the model and joint properties in cach set were assumed to be indentical. Passive, full-grouted rockbolts were cosidered in the numerical model. The visco-plastic deformations of joints and rockbolts were assumed to be governed by Mohr-Conlomb and von Mises yield criteria, respectively. With the ability of removing elements, the model can simulate the multi-step excavation-suppport sequences. The reliability and applicability of the model to the stability analysis for the underground excavation in pratice was checked by simulating the behavior of underground crude oil storage caverns under construction.

• Transactions of Materials Processing
• /
• v.7 no.2
• /
• pp.127-138
• /
• 1998

Process design of multi-step wire drawing process, conducted by means of finite element analysis and ANN(Artificial Neural Network) has been considered. The investigated problem involves the ade-quate selection of the drawing die angle and the correspondent reduction rate in the condition of desired initial and final diameter. Combinations of the process parameters which are used in finite ele-ment simulation are selected by using the orthogonal array. Also the orthogonal array. Also the orthogonal array and the results of finite element simulation which are related to the process energy are used as train data of ANN. In this study it is shown that the application of new technique using ANN and Othogonal array table to the process design of metal forming process is useful method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.10 s.181
• /
• pp.2451-2460
• /
• 2000

In order to minimize straightness error of deflected shaft, a geometric adaptive straightness controller system is studied. A multi-step straightening and a three-point bending process have been developed for the geometric adaptive straightness controller. Load-deflection relationship, on-line identification of variations of material properties, on-line springback prediction, and real-time hydraulic control methodology are studied for the three-point bending process. By deflection pattern analysis and fuzzy self-learning method in the multi-step straightening process, a straightening point and direction, desired permanent deflection and supporting condition are determined. An automatic straightening machine has been fabricated for rack bars by using the developed ideas. Validity of the proposed system is verified through experiments.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1997.03a
• /
• pp.144-147
• /
• 1997

Process design of multi-step wire drawing process, conducted by means of finite element analysis and ANN(Artificial Neural Network), has been considered. The investigated problem involves the adequate selection of the drawing die angle and the correspondent reduction rate sequence in the condition of desired initial and final diameter. Combinations of the process parameters which are used in finite element simulation are selected by using orthogonal array. Also the orthogonal array and the results of finite element simulation which are related to the process energy are used as train data of ANN. In this study, it is shown that the new technique using ANN is useful method in application to the wide range of metal forming process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.871-874
• /
• 2002

Many malfunctions take place in container crane spreader due to impact. So we designed a 2DOF hydraulic impact absorbing system with multi-step damping coefficient and studied the effect of orifice's interval and damping coefficient. The damping coefficient of upper piston was found to be 180 N.s/m, and the orifice's interval to be 9mm, the max reaction force and the average reaction force might be lowest. Compared with a general 2-DOF impact absorbing system, the max reaction force reduced by 46%., and average reaction force reduced by 5%.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.854-859
• /
• 2000

When the round bar with step is twisted and bent, stress concentration is occurred in the irregular geometric parts. Two dimensional axisymmetric stress analysis is carried out according to the geometric change of the stress-concentrated part of round bar with step. Three dimensional cases are also investigated.

• Proceedings of the KSME Conference
• /
• 2001.06c
• /
• pp.94-99
• /
• 2001

Theoretical analysis using finite element method are peformed in order to clarify the formation of the flare-shape defect for multi-step tube sinking process. The parameters of concern were the friction between the tube and the die, and geometrical parameters, such as the die inclination angle, the diameters of the die entrance and exit, and the curvature at the corner of the die exit. The effect of the curvature at the comer of the die exit is dominant for determining the flare-shape defect. In order to minimize the flare-shape defect the curvature at the corner of the die exit should be increased up to a certain level(120mm). Using three-step tube sinking die sets which have different curvatures at the comer of the die exit, several numbers of tests were performed and its results are compared with that of theoretical analysis.