• 제목/요약/키워드: montmorillonite content

검색결과 72건 처리시간 0.027초

국내산(國內産) 벤토나이트의 몇 가지 물리화학적(物理化學的) 특성(特性)에 관(關)하여 (Basic Physico-Chemical Properties of Representative Ca-Bentonites from Tertiary Sediments)

  • 문희수;유장한;김종환;조한익
    • 자원환경지질
    • /
    • 제20권3호
    • /
    • pp.159-168
    • /
    • 1987
  • Some physico-chemical properties such as surface area, moisture content, cation exchange capacity, swelling rate, pH, viscosity and liquid limit have been determined for evaluation of Cabentonite deposit occurring in four localities; Yonil, Gampo, Haseo and Pohang, in Gyeongsang-do. Montmorillonite contents can be derived from surface area measurement. Enhancement of liquid limit values and swelling volume were observed in the samples which had higher exchangeable Na ion and finer particle-size distribution. Identical results were observed even in the Na-exchanged samples. This suggests that aggregation effects have a great influence on physico-chemical properties. Aggregation of montmorillonite were controlled not only burial depth but also composition of exchangeable cation. Consequently, sample occurred in Yonil area where has the greatest burial depth in the area show somewhat lower physico-chemical properties than those of samples occurred in the other localities. However, the basic test applied in this study provides very useful preliminary information relating to its commercial potential.

  • PDF

Mechanical and Water Barrier Properties of Soy Protein and Clay Mineral Composite Films

  • Rhim, Jong-Whan;Lee, Jun-Ho;Kwak, Hyo-Sup
    • Food Science and Biotechnology
    • /
    • 제14권1호
    • /
    • pp.112-116
    • /
    • 2005
  • Composite films were prepared with soy protein isolate (SPI) and various clay minerals by casting from polymer and clay water suspension. Effects of clay minerals on film thickness, moisture content (MC), tensile strength (TS), elongation at break (E), water vapor permeability (WVP), and water solubility (WS) were tested. Properties including thickness, surface smoothness, and homogeneity of films prepared with organically modified montmorillonite (O-MMT), Wamok clay (W-clay), bentonite, talc powder, and zeolite were comparable to those of control SPI films. TS increased significantly (p<0.05) in films prepared with O-MMT and bentonite, while WVP decreased significantly (p<0.05) in bentonite-added films. WS of most nanocomposite films decreased significantly (p<0.05).

국내 토목용 벤토나이트의 물리화학적 특성 (Physico-chemical Properties of the Bentonites Used for the Civil Engineering Works in Korea)

  • 황진연;박성완;황한석
    • 지질공학
    • /
    • 제7권2호
    • /
    • pp.127-137
    • /
    • 1997
  • 현재 국내에 사용되는 토목용 벤토나이트에 대하여 점도, 팽윤도, 양이온교환용량 (CEC) 및 화학성분 등의 물리화학적 특성과, X-선 회절분석 및 적외선 분광분석을 이용하여 구성광물의 함량 및 그 특성을 비교 검토하였다. 그 결과 이들 벤토나이트의 몬모릴로나이트의 함량은 50-79%의 비교적 넓은 범위를 나타내었다. 이들은 몬모릴로나이트 함량의 증가에 따라 점도, 팽윤도, 함수량, 메칠렌불루 흡착량, 양이온 교환용량, 점토입도의 함량 등이 대체적으로 증가하는 상관관계가 나타났다. 이들 특성들간에서도 서로의 상관관계가 잘 나타나므로 간접적인 특성의 파악에 본 자료가 이용될 수 있을 것으로 생각된다. 그러나 일부 시료에서는 특성에 따라 일반적인 경향과 다른 상관관계를 나타내는데 이는 원광석중 구성광물의 특성과 제조방법에 따른 혼합물질의 차이가 기인되는 것으로 생각된다. 몬모릴로나이트의 함량이 가장 적은 시료는 토목용 벤토나이트의 역할에 요구되는 여러 물리화학적 특성도 모두 열세한 것으로 나타났다.

  • PDF

셀룰로오스 디아세테이트/몬모릴로나이트 나노복합체의 제조 및 기계적 물성 (Preparation and Mechanical Properties of Nanocomposite of Cellulose Diacetate/Montmorillonite)

  • 조미숙;최성헌;남재도;이영관
    • 폴리머
    • /
    • 제28권6호
    • /
    • pp.551-555
    • /
    • 2004
  • 셀룰로오스 디아세테이트에 다양한 종류의 가소제와 몬모릴로나이트를 메틸렌 클로라이드/에탄올 (9:1 w/w) 혼합용매에 첨가해 나노복합 필름 (nanocomposite film)을 제조하였다. 시차 주사 열분석 (DSC)을 이용하여 제조된 셀룰로오스 디아세테이트 필름의 열적 특성 (T$_{g}$)을 관찰하였으며, 가소제 함량이 증가함에 따라 T$_{g}$가 감소함을 관찰할 수 있었다. X-ray 회절 (XRD)을 이용하여 셀룰로오스 디아세테이트 필름내에서 몬모릴로나이트가 분산되는 정도를 관찰하였으며, 인장 강도와 인장 탄성률을 측정하여 셀룰로오스 디아세테이트 필름의 기계적 물성을 관찰하였다. 가소제의 함량을 30 wt%까지 증가시켰을 때 인장 탄성률은 1930 MPa에 1131 MPa로 감소하였고, 몬모릴로나이트의 함량을 7 wt%까지 증가시켰을 때 1731 MPa에서 2272 MPa로 증가하였다. 셀룰로오스 디아세테이트 필름의 기계적 물성은 가소제를 첨가할수록 감소하지만, 몬모릴로나이트의 첨가로 강화시킬 수 있다.다.

포항-울산간의 점토자원의 지질과 그 물리화학적 특성에 관한 연구 (A Study on Geology of Clay Mineral Deposits of Pohang-Ulsan Area and their Physico-Chemical Properties)

  • 김옥준;이하영;김서운;김수진
    • 자원환경지질
    • /
    • 제4권4호
    • /
    • pp.167-215
    • /
    • 1971
  • I. Purpose and Importance of the Study The purpose of the present study is to clarify to geological, mineralogical, and physico-chemical properties of the clay minerals deposits imbedded in the Tertiary sediments in the areas between. Pohang and Ulsan along southeastern coastal region of Korea. These clays are being mined and utilized for filter and insecticide after activation or simple pulverizing, nontheless activated clays are short coming as chemical industry in Korea has been rapidly grown in recent years. In spite of such increase in clay demand, no goological investigation on clay deposits nor physico-chemical properties of the clays have been carried out up to date. Consequently activated clays produced in Korea is not only of low grade but also of shortage in supply, so that Korea has to import activated clays of better grade. The importance of the present study lies, therefore, on that guiding principle could be laid down by knowing stratigraphical horizons, of clay deposits and fundamental data of improving grade of activated clays might be derived from the results of physico-chemical examinations. II. Contents and Scope of the study The contents of the study are pinpointed down in the following two subjects: 1) General geological investigation of Tertiary formations distributed in the areas between Pohang and UIsan, and detail geological study of the bentonitic clay deposits imbedded in them. 2) To clarifty physico-chemical characteristics of the clays by means of chemical analysis, X-ray diffraction and electron microscope. The scope of the study involves the following there points: i) Regional geological investigation-This investigation has been carried out in order to find out the distribution of Tertiary sediments and exact location of clay mineral deposits in the areas between Pohang and UIsan. ii) Detail geological investigation-This has been concentrated in and around the clay deposits which. had been found out by the regional investigation. iii) Laboratory researchs include i) age determination and correlation of Tertiary sediments by paleontological study, and ii) Chemical analysis, X-ray diffraction, and electron microscopic studies on clays, samples taken from various clay deposits. III. Research Results and Suggestions 1) The geology of the area investigated is composed mainly of Janggi and Beomgokri groups of Miocene age in ascending order rested on the upper Silla system, Balkuksa granite and volcanic rocks of upper Cretaceous age as base. 2) Janggi group is composed in ascending order of Janggi conglomerate, Nultaeri rhyolitic tuff, Keumkwangdong shale, two beds of lignite-bearing formations which consist of alternation of conglomerate, sandstone and mudstone, and andesitic, rhyolitic, and basaltic tuff beds. 3) Beomgokri group is mainly composed of andesitic to rhyolitic tuff interlayered by conglomerate and tuffaceous sandstone. In the areas around boundary between North-and South Kyeongsang-do is distributed Haseori farmation which is composed of conglomerate, sandstone, mudstone and andesitic to rhyolitic tuff, and which is correlated to Eoilri formation of Janggi group. 4) Clay deposits of the area are interbedded in Eoilri, Haseori, Nultaeri tuff, Keumkwangdong shale, upper and lower horizon of the lower lignite-bearing seam, and Keumori rhyolitic tuff formations of Janggi group; and are genetically classi.fied into four categories, that is, i) those derived from volcanic ash beds(Haseori and Daeanri deposits), ii) those of secondary residual type from rhyolitic tuff beds(Seokupri deposits), iii) Clay beds above and beneath the lignite seams, (Janggi and Keumkwangdong deposits), and iv) those derived from rhyolitic tuff beds(Sangjeong and Tonghae deposits). 5) Mineral constituents of clay deposits are, according to X-ray diffraction, montmorillonite accompanied in different degree by cristobalite, plagioclase, quartz, stilbite, and halloysite in rare occasion. The clays are grouped according to mineral composition into four types; i) those consist mostly of montmorillonite, ii) those composed of montmorillonite and cristobalite, iii) those composed of montmorillonite and plagioclase, and iv) those composed of montmorillonite, plagioclase and quartz. 6) Clays interbedded in Haseori formation and vicinity of lignite seams belong to the first type, are of good quality and derived either from volcanic ash bed, or primary clay beds near lignite seams. Clays belonged to other types are derived from weathering of rhyolitic tuff formations and their quality varies depending upon original composition and degree of weathering. Few clays in secondary residual type contain small amount of halloysite. 7) Judging from analytical data, content of silica($SiO_2$) varies proportionally with content of cristobalite, and alumina($Al_2O_3$) content does not vary with that of plagioclase, but increases in the sedimentary bedded type of deposits. 8) It is unknown whether or not these days could be upgraded by beneficiation since no grain size of these impurities nor beneficiation test had been studied. 9) Clay beds derived from valcanic ash layers or sedimentary layers at the vicinity of lignite seams are thin in thickness and of small, discontinueous lenticular shape, although they are of good quality; and those derived from rhyolitic tuff formations or residual type from tuff are irregular in both occurrence and quality. It is, therefore, not only very difficult but also meaningless to calculate its reserve, and reserve estimation, even if done, will greatly be deviated from practically minable one. Consequently, way of discovery and exploitation of clay deposits in the area under consideration is to check the geologically favorable areas whenever needed.

  • PDF

Nanofiller를 첨가한 에폭시 수지의 구조적 특성 (Structural properties of the epoxy resin which adds the Nanofiller)

  • 이창공;이성갑;안병립;원우식;우형관;노현지
    • 대한전기학회:학술대회논문집
    • /
    • 대한전기학회 2008년도 제39회 하계학술대회
    • /
    • pp.1234-1235
    • /
    • 2008
  • To add Nanofiller in the epoxy which is used with the solid insulation material of existing and is a research which observes the improvement of the structural quality to produce the Nanocomposite. Montmorillonite uses with Nanofiller, MMT of the content expense (wt%) which is various and mixed an epoxide and produced sample. According to content of the sample result MMT according to respectively content expense to measure SEM photographing which is the possibility of knowing the minute structure of section with sample where is produced and the tensile strength will be able to observe the change of quality. MMT silicate layer uniformly more in the result and within epoxy matrix, being dispersed, will be able to observe.

  • PDF

유기점토를 이용한 유기염소계 농약(2,4-D, atrazine) 오염 저감 (Attenuation of Chlorinated Pesticides(2,4-D, atrazine) Using Organoclays)

  • 최지연;신원식
    • 한국환경과학회지
    • /
    • 제20권2호
    • /
    • pp.185-197
    • /
    • 2011
  • Sorption of chlorinated pesticides such as 2,4-dichlorophenoxyacetic acid (2,4-D) and atrazine onto natural clays (montmorillonite and zeolite) modified with cationic surfactant, hexadecyltrimethyl-ammonium (HDTMA) and a natural soil was investigated using batch adsorbers. The clays were transformed from hydrophilic to hydrophobic by the cation exchange between clay surface and HDTMA up to 100% of the cation exchange capacity (CEC). Physicochemical characteristics of the sorbents such as pH, PZC (point of zero charge), organic carbon content ($f_{oc}$), fourier transform infrared spectroscopy (FT-IR), differential thermogravimetric analysis (DTGA) and X-ray diffraction (XRD) were analyzed. Sorption isotherm models such as Freundlich and Langmuir were fitted to the experimental data, resulting Langmuir model ($R^2$ > 0.986) was fitted better than Freundlich model ($R^2$ > 0.973). Sorption capacity ($Q^0$) for 2,4-D and atrazine was in the order of HDTMA-montmorillonite > HDTMA-zeolite > natural soil corresponding to the increase in organic carbon content ($f_{oc}$). The sorption of the pesticides was also affected by pH. The sorption of 2,4-D decreased with the increase in pH, whereas that of atrazine was not changed. This indicated that the sorption capacity ($Q^0$) of 2,4-D and atrazine was not affected by the solution pH because they exist as anionic (deprotonated) forms at pH above pKa. The results indicate that organoclay has a promising potential to reduce chlorinated pesticides in the effluent from golf courses.

방사성폐기물 처분장 공학방벽 재료로서의 국산 벤토나이트 및 제올라이트에 대한 물리화학적 특성 평가 (Assessment of Physicochemical Properties of Domestic Bentonite and Zeolite as Candidate Materials for a Engineered Barrier in a Radwaste Repository)

  • 정찬호
    • 지질공학
    • /
    • 제9권2호
    • /
    • pp.89-100
    • /
    • 1999
  • 핵폐기물 처분장 공학방벽재로서의 우리나라 제 3 기층에서 산출되는 벤토나이트와 제올라이트의 활용 가능성을 물리화학적 특성을 중심으로 평가하였다. 연일 및 감포일대 제 3 기층의 9개 대표적인 벤토나이트 광산과 6개의 제올라이트 광산에서 채취한 자연산 시료와 관련회사의 추천상품시료에 대해 X-선 회절 분석, 팽윤도 측정, 양이온교환능 측정, 비표면적 측정, 몬모릴로나이트의 함량계산, 유기탄소함량 분석, 시차 열분석(DTA), 편광현미경 관찰, 주사전자현미경(SEM)관찰 및 전자현미분석(EPMA)을 실시하여 각 분석항목을 비교 평가하였다. 연구결과를 종합하면 U-41 및 G-46의 광산에서 산출되는 벤토나이트와 대도 및 Y-1호 광산의 제올라이트가 인공방벽재료로 갖추어야할 물리화학적 특성이 최적인 것으로 평가된다.

  • PDF

EVA/Clay Nanocomposite by Solution Blending: Effect of Aluminosilicate Layers on Mechanical and Thermal Properties

  • Pramanik, M.;Srivastava, S.K.;Samantaray, B.K.;Bhowmick, A.K.
    • Macromolecular Research
    • /
    • 제11권4호
    • /
    • pp.260-266
    • /
    • 2003
  • Ethylene vinyl acetate (EVA)/clay nanocomposites were synthesized by blending a solution of ethylene vinyl acetate copolymer containing 12% vinyl acetate abbreviated as EVA-12 in toluene and dispersion of dodecyl ammonium ion intercalated montmorillonite (l2Me-MMT) in N,N-dimethyl acetamide (DMAc). X-ray patterns of sodium montmorillonite ($Na^+$-MMT) and 12Me-MMT exhibited $d_{001}$ peak at $2{\theta}=7.4^{\circ}$ and $2{\theta}=5.6^{\circ}$ respectively; that is, the interlayer spacing of MMT increased by about 0.39 nm due to intercalation of dodecyl ammonium ions. The XRD trace of EVA showed no peak in the angular range of $3-10^{\circ}(2{\theta})$. In the XRD patterns of EVA/clay hybrids with clay content up to 6 wt% the basal reflection peak of 12Me-MMT was absent. leading to the formation of delaminated configuration of the composites. When the 12Me-MMT content was 8 wt% in the EVA-12 matrix, the hybrid revealed a peak at about $2{\theta}=5.6^{\circ}$, owing to the aggregation of aluminosilicate layers. Transmission electron microscopic photograph exhibited that an average size of 12-15 nm clay layers were randomly and homogeneously dispersed in the polymer matrix, which led to the formation of nanocomposite with delaminated configuration. The formation of delaminated nanocomposites was manifested through the enhancement of mechanical properties and thermal stability, e.g. tensile strength of an hybrid containing only 2 wt% 12Me-MMT was enhanced by about 36% as compared with neat EVA-12.

우리나라 형석광상(螢石鑛床)의 유체포유물(流體包有物) 연구(硏究) (Fluid Inclusion Studies of the Fluorite Deposits in Korea)

  • 박희인
    • 자원환경지질
    • /
    • 제9권1호
    • /
    • pp.27-43
    • /
    • 1976
  • The flourite in Hwacheon, Hwanggangri and Keumsan district are major fluorite producing areas in Korea. The fluorite deposits of Hwacheon district are wholly fissure filling hydrothermal veins embedded in Precambrian gneiss and schists and Jurassic granites. Also some fluorite deposits are emplaced in felsite whose age is unknown. Emplacement of most fluorite veins of the district are controlled by EW fracture system. Fluorites are generally accompanied to chalcedonic quartz and also kaolinite, montmorillonite, dickite and calcite in parts. Vertical and lateral mineral zonings are not distinct. The fluorite deposits in the Hwanggangri district are wholly embedded in limestone and other calcareous sediments of Paleozoic Yeongweol Group. Most of the fluorite deposits belong to one of two categories which are steeply. dipping veins and gently dipping replacement deposits adjacent to Late Cretaceous(83-90mys) granite bodies. The strikes of fluorite veins of Hwanggangri district mostly occupy the fractures of $N30^{\circ}-40^{\circ}E$ and $N30^{\circ}-40^{\circ}W$ system. Fluorites are accompanied to calcite, milky quartz, chalcedonic quartz, and also montmorillonite, kaolinite in parts. But in some deposits, scheelite, various sulfide minerals and barite are accompanied. Emplacement of fluorite deposits are largely controlled by lithology and structures of this district. In some deposits fluorite veins gradate to scheelite veins and also telescoping of the mineral zones are found in this district. In the Keumsan district, fissure-filled fluorite veins and replacement deposits are mostly emplaced in limestone of Paleozoic Yeongweol Group, late Cretaceous quartz-porphyry, granite and sandstone. Some deposits are emplaced in Precambrian metasediments. Mineralogy and other characteristics of the deposits in this district is similar to those of Hwanggangri district. Fluid inclusion studies reveal the difference of salinities, $CO_2$ contents of ore fluid and temperatures during fluorite mineral deposition in the these districts. In Hwacheon district, ore-fluids were comparatively dilute brine and low $CO_2$ content. Filling temperatures ranges $104^{\circ}C$ to $170^{\circ}C$. In the Chuncheonshinpo mine, most deeply exploited one in this district, salinitles range 0.5-2. 2wt. % NaCl and filling temperatures range from $116^{\circ}C$ to $143^{\circ}C$. In the Hwanggangri district, ore fluids were complex and filling temperature ranges very widly. In the contact metasomatic fluorite deposits, ore fluid were NaCl rich brines with moderate $CO_2$ content and filling temperatures range from $285^{\circ}C$ to above $360^{\circ}C$. Fluids inclusions in tungsten and sulfide minerals bearing fluorite veins show high $CO_2$ content up to 31wt. %. Filling temperature ranges from $101^{\circ}C$ to $310^{\circ}C$. Fluids inclusions In mainly fluorite bearing veins were more dilute brine and low $CO_2$ contents. Filling temperatures range from $95^{\circ}C$ to $312^{\circ}C$. Filling temperature of fluid inclusions of Keumsan district are between $95^{\circ}C$ and $237^{\circ}C$. Data gathered from geologic, mineralogic and fluid inclusion studies reveal that fluorite mineralization in H wacheon district proceeded at low temperature with dilute brine and low $CO_2$ content. In Hwangganri district, fluorite mineralization proceeded by several pulse of chemically distinct ore fluids and formed the mineralogically different type of deposits around cooling granite pluton which emplaced comparatively shallow depth.

  • PDF