• 한국생산제조학회지
• /
• 제22권3호
• /
• pp.343-348
• /
• 2013

In line with the advances in factory automation, various pieces of equipment are now operated in batch processes controlled by computers. However, many kinds of faults can occur in complicated and large systems, which can result in low productivity and economic loss. The reliability and safety of systems have been studied because of the difficulty of determining the severity and location of faults. Therefore, it is necessary to detect and diagnose such faults in order to guarantee the reliability and safety of the equipment. In this paper, a diagnosis method for the ball bearings of a hydraulic pump is applied using a vibration signal for the maintenance of injection molding equipment. The bearings' defects are selected as a main failure mode through a failure mode and effect analysis (FMEA). Usually, there are nonlinear and impulse components of vibration in a ball bearing with faults. For the effective fault diagnosis of a ball bearing, nonlinear diagnostic methods and time-frequency analysis are applied, in addition to the methods currently used, such as power spectrum, time series analysis, and statistical methods. As a result of this study, a failure diagnosis system is provided that is useful even for non-experts. This is a condition-based method that makes it possible to resolve problems in a timely and economical way, in contrast to the prior method, which required regular but wasteful maintenance based on the experience of expensive external experts.

• 한국산학기술학회논문지
• /
• 제13권9호
• /
• pp.3815-3821
• /
• 2012

LCD 프레임은 중 대형 TFT-LCD BLU의 기본형상을 유지시켜주는 중요한 부분이다. 중 대형 LCD 프레임을 효율적으로 생산하기 위해 1 캐비티에서 2 캐비티 사출 공정으로의 개선이 필요하다. 2 캐비티 금형 구조는 콤팩트하게 되었고 핫 런너 존이 증가되었기 때문에 사출온도를 조절하기 어렵게 되었다. 본 연구에서는 2 캐비티 사출성형공정으로 생산된 프레임에 대한 품질을 평가하기 위해서 유한요소해석 프로그램을 사용하여 사출해석을 수행하였다. 1 캐비티와 2 캐비티 공정에서 계산된 사출압력과 최대 변형량은 각각 41.13 MPa과 1.62 mm, 40.49 MPa과 1.66 mm이다. 1 캐비티 프레임의 측정된 최대 굽힘 하중, 표면거칠기가 140 N, 0.13 ${\mu}m$, 인데 비하여 2 캐비티 중 좌, 우 프레임의 측정값들은 209 N, 0.08 ${\mu}m$와 193 N, 0.10 ${\mu}m$이다. 열화상은 2 캐비티 금형 중 좌 우 금형 온도의 최대 표준 편차값은 $1.23^{\circ}C$임을 나타내고 있다. 시뮬레이션과 측정은 전체적으로 2 캐비티 사출공정의 프레임 품질이 1 캐비티 품질보다 나쁘지 않다는 것을 보여주고 있다. 그러나 2 캐비티 공정에서 프레임의 최대 굽힘 하중값은 1 캐비티 공정의 하중값보다 매우 증가되었다.

• 보존과학회지
• /
• 제28권4호
• /
• pp.353-366
• /
• 2012

이 연구에서는 완주 송광사 소조사천왕상의 제작기법을 해석하였으며, 소조토의 산지를 추정하여 동일재료로 보존처리 및 복원할 수 있는 기초자료를 확보하였다. 사천왕상에 사용된 소조토는 층위별로 다양한 재질적 특성을 나타냈다. 원소조토로 추정되는 초벌층과 중벌층은 성인적으로 동일한 토양이 사용되었으며, 마감층은 약간의 차이를 보였으나 거의 유사한 토양으로 확인되었다. 그러나 보수층은 모든 분석결과에서 원소조토와 재질특성이 일치하지 않았다. 감마선 촬영 결과, 사천왕상의 제작은 심목과 부목을 강선과 'ㄷ'자 꺽쇠, 못, 새끼줄 등으로 연결하여 뼈대를 형성하고, 이 위에 소조토를 조성한 것으로 나타났다. 소조토의 산지해석 결과, 추정산지 일대 토양은 마감층에 사용된 토양과 동일기원으로 나타나 보존처리용 재료로 적합할 것으로 판단된다. 이 결과는 소조상의 제작기법 연구에 기여할 것으로 기대된다.

• Design & Manufacturing
• /
• 제12권2호
• /
• pp.27-33
• /
• 2018

Korea's automobile industry, which has grown rapidly to become the world's fifth-largest automobile producer, To cope with environmental pollution and energy problems in order to prevail competitive edge in global market We are investing a lot of research personnel and costs. Among them, for realizing alternative light weight It is a part of the automobile module system that has achieved the technological development before the breakthrough in the injection molding process in the press process. Door module PNL was the subject of research. The door module PNL is expected to cause warpage before the mold production due to the thin and flat product characteristics and fiber orientation characteristic of the material. In this paper, CAE analysis and reverse correction tool Design. CAE analysis to obtain the results of weld line position, bending position and deformation value Through the correction tool, think3, the original product was modified before the mold production to improve the completeness of the parts. In fiber orientation, the position and size of the cooling channel in the mold, the position and size of the gate, Temperature, pressure, time, and work environment. Compared with the result of CAE analysis, the product that was reverse-corrected by Think3 was manufactured, and injection molding was performed. Injection molding products were tested 24 hours later. 3.5 mm to 7.0 mm, and under the fixed condition, the deviation was from 1.1 mm to 1.5 mm. Unlike the CAE analysis, the deviation of the actual injection pressure and the cooling temperature, the fiber orientation of the material, In order to solve this problem, it is necessary to compare the injection conditions with the database, I knew I had to catch the standard.

• Composites Research
• /
• 제36권5호
• /
• pp.310-314
• /
• 2023

VaRTM(Vacuum assisted resin transfer molding)과 VAP(Vacuum assisted process) 공정은 RTM(Resin transfer modling) 공정의 한 종류로서, 대형구조물을 저가에 제작할 수 있는 대표적인 탈 오토클레이브(OOA, Out of Autoclave) 공정이다. 본 논문에서는 VaRTM과 VAP 공정을 상호 비교하기 위하여 수지 충진시험을 진행하였으며, 충진과정과 치수 안정성 등을 상호 비교하였다. 또한, 충진과정을 모사할 수 있는 해석기법을 개발하였으며, 유전센서를 사용하여 수지의 유동선단을 검출하여 이를 해석결과와 상호 비교하였다. 수지 충진시험 결과, 복합재 평판의 총 충진시간은 VAP공정은 48분, VaRTM 공정은 145분으로 측정되어, VAP 공정에 의한 충진시간이 VaRTM 대비 약 67% 단축되었으며, VAP공정이 VaRTM 공정에 비해 복합재 평판의 두께조절능력과 균일도가 우수함을 확인하였다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.333-334
• /
• 2002

Injection-compression molding parts are many cases with complicated boundary condition which is difficult to analysis of mold characteristics precisely. In this study, the effects of various process parameters such as multi-point gate location, initial charge volume, injection time and pressure have been investigated using finite element method to fomulate the melt front advancement during the mold filling process. A general governing equation for tracking the filling process during injection-compression molding is applied to volume of fluid method. To verify the results of present analysis, they are compared with those of the other paper. The results show a strong effect of processing conditions as a result of variations in the three-dimensional complex geometry model.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.381-388
• /
• 2003

The paper presents our study of development for multi-cavity preform mold system which consists of hot runner system and valve gate. For this purpose, stretching blow molding process and preform injection process were simulated by Polyflow and Moldflow. Based on various results of the preform injection process analysis, process planning was established. The sectional thickness distribution of preform was optimized. Preform injection mold system was designed by these technical analysis data. Finally, 24-cavity preform mold system was successfully developed.

• 소성∙가공
• /
• 제20권1호
• /
• pp.29-35
• /
• 2011

In the design of the injection molding process, various parameters including mold design parameters and molding conditions should be investigated to improve part quality. The mold temperature is one of important processing parameters that affect the flow characteristics, surface appearance, part deformation, mechanical properties, etc. Numerical analyses have been used to predict the temperature distribution of the mold under the given cooling or heating conditions. However, conventional analyses have been performed by assuming that the mold material is a single solid even though a number of plates are assembled to construct an injection mold. In the present study, a numerical approach considering the thermal contact resistance is proposed to provide more reliable prediction of the mold temperature distribution by reflecting the heat-resistance between assembled mold plates.

• 한국주조공학회지
• /
• 제1권3호
• /
• pp.19-29
• /
• 1981

An emphasis has been placed on the importance of selecting a sand for furan sand process, which ie affected by the properties of sand. Investigations have been carried out to use the domestic artificial sands for the furan sand process. For laboratory investigations, the sands have been prepared and tested for chemical analysis, loss on ignition, sieve analysis, AFS grain fineness number, grain shape, PH value, acid demand, surface shape, theoretical surface area, moisture absorption, crushing durability and compressive strength and S. S. I. of molding sands. Most commercial sands have been found to be able to be used. The main requirement of the sands has been shown to be that 3 or 4 screen sands, AFS no.40-70 (or 100), of low acid demand, good surface area and good grain shape require less resin and catalyst to give an adequate strength.

• 한국기계가공학회지
• /
• 제10권5호
• /
• pp.72-78
• /
• 2011

Currently, for the damper case, the material produced by cast/forge welding is mechanically processed and then the final product is mass-produced. By cutting the cast/forge welded material, the issues of excessive cutting time, multiple process production, and a large amount of chips (40% loss from the original material) arise, causing increased production cost and reduced profitability. Thus, in this study, the incremental forming technology which generates no chips was applied in production. Analysis was excuted for 1st and 2nd works by change of tool diameter and working tool. For this, 3D molding and analysis were executed, which was applied to the processing the result, successful processing could be achieved through a few trials of molding processing according to tool forming and rotation counts.