• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.78-84
• /
• 2012

Mold may experience deterioration of molding quality as the abrasion of mold occurring due to friction between mold and molded product works as allowance in the course of press process. Therefore, to improve the wear-resistance of mold, methods like nitriding, carburizing, flame and induction surface hardening treatment etc have been applied. However, as such methods are accompanied by problems like shape limitation or product deformation etc, laser surface treatment technology is under review as surface treatment method that can solve such problems. Therefore, in this study, mold material cast iron was surface-treated by using high power diode laser. In previous report 1 and report 2, the heat treatment characteristics were compared by the differences of die materials and shapes, then this paper observed microstructure by using optical microscope and scanning electronic microscope to analyze the structural difference of hardened zone, interface area and base metal after heat treatment. And the structural condition was grasped through EDS. As a result of microstructure, hardened zone showed formation of acicular martensite.

• Journal of Korea Foundry Society
• /
• v.43 no.4
• /
• pp.194-200
• /
• 2023

The heat transfer of the mold in the casting process has been calculated by considering the mold as a uniform isotropic material. Since the mold was not a uniform isotropic material, however, the calculation was performed with approximate values, and in particular, estimated values were used when considering compaction and the amount of added binder. In this study, a calculation algorithm of the thermal properties of the sand mold was developed. An algorithm for calculating the thermal conductivity and specific heat based on a thermal resistance model in the case of mono-dispersed sand grains was also developed and applied to sand molds with various size distributions. The thermal properties of sand were calculated for artificial sand, and relatively close values compared to the experimental values were obtained.

• Electrical & Electronic Materials
• /
• v.35 no.3
• /
• pp.22-31
• /
• 2022

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.10 s.175
• /
• pp.39-48
• /
• 2005

As the industrial development is accelerated, a new machining process and system are keenly required to achieve super precision surface finish. Especially to get ground surface finish fer complicated and narrow inner shape of molds, it is impossible with the existing methods so that a new method is being required to be developed. A new material, called Magic(MAGnetic Intelligent Compounds), is finally made and it is called Magic machining that uses this material. There is a way to make a material as follows, the mixture of magnetic particles, bonding material and particles of abrasive grain should be melt down by proper heat, and then this mixture put in a mold and cool down in magnetic field which has a uniform direction. This new polishing method is spotlighted as an excellent solution to the existing problems. However it hasn't reported any study about the influence of the machining conditions of polishing velocity, amplitude and polishing pressure to the surface roughness yet. This study would examine closely the influence of polishing conditions of the Magic polishing tool to the surface finish to decide the optimum polishing condition and to standardize the Magic polishing work.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.3
• /
• pp.251-260
• /
• 2023

The construction of free-form structures with intricate curved exteriors necessitates the use of bespoke molds. To fulfill this requirement, a blend of Phase Change Material(PCM) and Ultra-High Performance Concrete(UHPC) is utilized. PCM endows the solution with recyclability, while UHPC facilitates the effortless execution of curvature in the mold fabrication process. However, it's worth mentioning that the melting point of PCM hovers around 58-64℃, and the heat emanating from UHPC's hydration process can potentially jeopardize the integrity of the PCM mold. Hence, experimental validation of the mold shape is a prerequisite. In the conducted experiment, UHPC was poured into two distinct mold types: one that incorporated a 3mm silicone sheet mounted on the fabricated PCM mold(Panel A), and the other devoid of the silicone sheet(Panel B). The experimental outcomes revealed that Panel A possessed a thickness of 3.793mm, while Panel B exhibited a thickness of 5.72mm. This suggests that the mold lacking the silicone sheet(Panel B) was more susceptible to the thermal effects of hydration. These investigations furnish invaluable fundamental data for the manufacturing of ultra-high strength irregular panels and PCM molds. They contribute substantially to the enrichment of comprehension and application of these materials within the realm of construction.

• Design & Manufacturing
• /
• v.2 no.2
• /
• pp.29-32
• /
• 2008

A back light unit (BLU) is a key module of a thin film transistor liquid crystal display (TFT-LCD), frequently utilized in various mobile displays. In this study, we experimentally characterize transcription and optical properties of concave and convex microlens arrays (MLAs) of light guide plate (LGP) fabricated by injection molding with polycarbonate as a LGP substrate material. Nickel mold inserts were manufactured by electroforming on the MLA which was fabricated by the thermal reflow of photoresist microstructures patterned by UV-photolithography. For the case of convex microlens, the height of replicated microlens was less than that of the mold insert while maintaining almost the same microlens diameter of the mold insert as the location of the microlens is far from the gate. In contrast, for the concave microlens, the diameter of replicated microlens was larger than that of mold insert, while showing almost the same microlens height as the mold insert. From the optical examination of replicated convex and concave MLAs, it was found that a higher luminance of the LGP was achieved by the concave MLAs compared to the convex MLAs (about 30% enhancement in this case)due to the utilization of a larger amount of light provided by the light sources.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.6
• /
• pp.468-472
• /
• 2005

In order to prevent adhering of molten glass on a mold wall, the wall is swabbed with lubricant oil before forming. However, the swabbing process can be removed from the entire processes of the glass forming if the mold wall is made of a porous sintered material. The purpose of the present study is to manufacture a sintered material(having a sintered density of $85{\~}90\%$)which is the most appropriate into. plane material for a glass mold. For the research, SUS310L-based coarse powder (${\~}150{\mu}m$) and SUS420J2-based fine powder ($40{\~}50{\mu}m$) were used for the compact materials, and effects of compaction pressure and sintering condition(atmosphere, temperature) were investigated. The results obtained were as fellows. (1) By means of solid phase sintering, a desired sintering density could not be achieved in any case when using a 310L-based powder having a large particle size. (2) When sintering green compacts(compaction pressure of $2ton/cm^2$) in a commercial vacuum furnace(at $1300^{\circ}C$ for 2 hours), the sintered compacts had densities of $6.2g/cm^3(79\%)$ for 310L + 0.03$\%$B, $6.6g/cm^3 (86\%)$ for 420J2, $7.3g/cm^3(95\%)$ for 420J2+(0.03)$\%$B, and $7.6g/cm^3(99\%)$ for 420j2+(0.06)$\%$B, respectively. As a result, it is regarded that sintered compacts having a desired porosity may be achieved by vacuum sintering the 420J2-based powder (low pressure compaction) and the 310L+0.03$\%$B-based powder (high pressure compaction).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1630-1635
• /
• 2005

The microstructure of the parts made by the microcellular injection molding process influence properties, including impact strength, tensile strength and density of material. Microstructure of microcellular plastics is divided into core foaming region and solid skin region. Core foaming region is influenced by pressure drop rate, viscosity and cell coalescence. However, actual mechanism of the skin layers is not known despite its importance. The study on the skin layer is getting important because foaming rate of the plastics is determined by the thickness ratio of the skin layer. Especially in case of large molded part, control of the skin layer is needed because skin layer thickness is changed largely. Therefore it is necessary to study variation in skin layer thickness with processing parameters. In this paper, the influence of temperatures in the mold cavity on the skin layer s thickness was also addressed. In addition, the relationship between the temperature distributions across cavity of the mold with impact strength on parts made with the microcellular injection molding process was addressed. In addition, the method to predict the variation in skin layer thickness with mold temperature is discussed.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 2001.12a
• /
• pp.65-68
• /
• 2001

Short shot is a molded part that is incomplete since insufficient material was injected into the mold. Remedial actions to solve short shot can be done by injection molding experts based on their empirical knowledge. Modifying mold and part, changing resin to less viscous one, and adjusting process conditions are general remedies. Experts of injection molding might try to adjust process conditions such as mold temperature, melt temperature, injection time based on their empirical knowledge as the first remedy because adjustment of process conditions is the most economic way in time and cost. However it is difficult to find appropriate process conditions as they are highly coupled and there are so many elements to be considered. In this paper, a fuzzy logic algorithm has been proposed to find an appropriate mold temperature. With the percentage of the insufficient Quantity of an injection molded part, an appropriate mold temperature can be obtained by the fuzzy logic algorithm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.9
• /
• pp.3895-3899
• /
• 2012

In this study, the start-type molded material, silicone resin(RTV-3040) was used to develop a mold that is utilized for embossing pattern. After selecting a required pattern using the commercial package (Freeform), we examined whether this is applicable to components creating projective embossed side on the surface. We responded to products that require corrosive pattern, such as aluminum mold, by making the starting type when small amounts of components are developing. However, the development of silicone mold that is applied to corrosive pattern showed the possible reduction in time and cost.