• Nuclear Engineering and Technology
• /
• v.56 no.3
• /
• pp.1100-1107
• /
• 2024

The nuclear waste attributes of near-term deployable SMRs were assessed using established nuclear waste metrics, which are the DU mass, SNF mass, volume, activity, decay heat, radiotoxicity, and decommissioning LLW volumes. Metrics normalized per unit electricity generation were compared to a reference large PWR. Three SMRs, VOYGR, Natrium, and Xe-100, were selected because they represent a range of reactor and fuel technologies and are active designs deployable by the decade's end. The SMR nuclear waste attributes show both some similarities to the PWR and some significant differences caused by reactor-specific design features. The DU mass is equivalent to or slightly higher than the PWR. Back-end waste attributes for SNF disposition vary, but the differences have a limited impact on long-term repository isolation. SMR designs can vary significantly in SNF volume (and thus heat generation density). However, these differences are amenable to design optimization for handling, storage, transportation, and disposal technologies. Nuclear waste attributes from decommissioning vary depending on design and decommissioning technology choices. Given the analysis results in this study and assuming appropriate waste management system and operational optimization, there appear to be no major challenges to managing SMR nuclear wastes compared to the reference PWR.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.1023-1026
• /
• 2005

In the ubiquitous computing environment, an intelligent vehicle is defined as a sensor node with a capability of intelligence and communication in a wire and wireless network space. To make it real, a lot of problems should be addressed in the aspect of vehicle mobility, in-vehicle communication, common service platform and the connection of heterogeneous networks to provide a driver with several intelligent information services beyond the time and space. In this paper, we present an intelligent information system for managing in-vehicle sensor network and a vehicle gateway for connecting the external networks. The in-vehicle sensor network connected with several sensor nodes is used to collect sensor data and control the vehicle based on CAN protocol. Each sensor node is equipped with a reusable modular node architecture, which contains a common CAN stack, a message manager and an event handler. The vehicle gateway makes vehicle control and diagnosis from a remote host possible by connecting the in-vehicle sensor network with an external network. Specifically, it gives an access to the external mobile communication network such as CDMA. Some experiments was made to find out how long it takes to communicate between a vehicle's intelligent information system and an external server in the various environment. The results show that the average response time amounts to 776ms at fixed place, 707ms at rural area and 910ms at urban area.

• Journal of Advanced Navigation Technology
• /
• v.20 no.1
• /
• pp.15-22
• /
• 2016

The A-SMGCS is a modular system defined in the ICAO manual on advanced surface movement guidance and control systems. Such systems aim to maintain the declared surface movement rate under all weather conditions while maintaining the required level of safety. In this paper, we find out the details and 14 modules'specific features that developing Level IV A-SMGCS in Korea. Also we figure out relation domestic regulations as SMGCS manual & visual aids manual in Korea and research foreign cases such as defined ICAO 9830 manual, EUROCONTROL's project 'EMMA2' document, and FAA advisory circular-150 manual. It will be used as analysis data that can be applied to the undefined A-SMGCS in Korea technical regulation.

• Journal of Korean Association for Spatial Structures
• /
• v.17 no.4
• /
• pp.59-68
• /
• 2017

This paper aims at finding some lessons applicable to successful implementation of 'The 3D Printing R/D Project' through both examining the process of adopting overseas industrialized housing production technological knowhow by home builders during the 1970's~1980's period and thereafter until now the various efforts to adjust the technologies efficiently to the Korea's unique situation. Some meaningful lessons can be summarized as follows; I) Deep understanding of 3DP technological know-why along with its inheritance, II) Readjusting of R/D period and goals(cf. Global leader Winsun's 15 years experiment), III) Restructuring for more collaborative R/D B&E system among participating researchers IV) Fostering 3DP expert-engineers and technicians from the early stage, V) Clearing legal barriers in users' adopting 3DP methods necessary, VI) Development of appropriate building material besides concrete. Therefore, it is highly recommended that the above-mentioned 6 lessons positively accepted and applied to the Research Implementation Plan in due course, especially by KICT consortium and KAIA under the guidance of Ministry of Land, Infrastructure and Transport.

• Nuclear Engineering and Technology
• /
• v.27 no.1
• /
• pp.84-95
• /
• 1995

Application of computer software to safety-critical systems is on the increase. To be successful, the software must be designed and constructed to meet the functional and performance requirements of the system. For safety reason, the software must be demonstrated not only to meet these requirements, but also to operate safely as a component within the system. For longer-term cost consideration, the software must be designed and structured to ease future maintenance and modifications. This paper present a software engineering process for the production of safety-critical software for a nuclear power plant The presentation is expository in nature of a viable high quality safety-critical software development. It is based on the ideas of a rational design process and on the experience of the adaptation of such process in the production of the safety-critical software for the Shutdown System Number Two of Wolsong 2, 3 & 4 nuclear power generation plants. This process is significantly different from a conventional process in terms of rigorous software development phases and software design techniques. The process covers documentation, design, verification and testing using mathematically precise notations and highly reviewable tabular format to specify software requirements and software design. These specifications allow rigorous, stepwise verification of software design against software requirements, and code against software design using static analysis. The software engineering process described in this paper applies the principle of information-hiding decomposition in software design using a modular design technique so that when a change is' required or an error is detected, the affected scope can be readily and confidently located. It also facilitates a sense of high degree of confidence in the ‘correctness’ of the software production, and provides a relatively simple and straightforward code implementation effort.

• Journal of Korea Society of Industrial Information Systems
• /
• v.8 no.2
• /
• pp.84-91
• /
• 2003

KOMPSAT series use software-controlled unregulated bus system in which the main bus is directly connected to a battery and the duty-ratio for PWM switch is controlled by the on-board satellite software. This paper proposes a new power-stage circuit that can be available for modularization of the power regulator which is used at the software-controlled unregulated bus system satellite. And we analyze the proposed power-stage operation according to its operating modes and verify it by performing software simulation and hardware experiment using prototype. We construct a parallel-module converter which is composed of proposed power-stages and perform experiment to verify modular characteristics of the proposed power-stage. Finally, we verify the usefulness of the proposed power-stage by comparing above results with those of a parallel-module converter made of conventional power-stages.

• Genomics & Informatics
• /
• v.2 no.4
• /
• pp.191-194
• /
• 2004

Exponentially increasing biopathway data in recent years provide us with means to elucidate the large-scale modular organization of the cell. Given the existing information on metabolic and regulatory networks, inferring biopathway information through scientific reasoning or data mining of large scale array data or proteomics data get great attention. Naturally, there is a need for a user-friendly system allowing the user to combine large and diverse pathway data sets from different resources. We built a data warehouse - BIOWAY - for analyzing and visualizing biological pathways, by integrating and customizing resources. We have collected many different types of data in regards to pathway information, including metabolic pathway data from KEGG/LIGAND, signaling pathway data from BIND, and protein information data from SWISS-PROT. In addition to providing general data retrieval mechanism, a successful user interface should provide convenient visualization mechanism since biological pathway data is difficult to conceptualize without graphical representations. Still, the visual interface in the previous systems, at best, uses static images only for the specific categorized pathways. Thus, it is difficult to cope with more complex pathways. In the BIOWAY system, all the pathway data can be displayed in computer generated graphical networks, rather than manually drawn image data. Furthermore, it is designed in such a way that all the pathway maps can be expanded or shrinked, by introducing the concept of super node. A subtle graphic layout algorithm has been applied to best display the pathway data.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.8
• /
• pp.1741-1748
• /
• 2005

In this paper, we describe VLSI design and performance evaluation of OCB-AES crytographic algorithm that simulataneously provides privacy and authenticity. The OCB-AES crytographic algorithm sovles the problems such as long operation time and large hardware of conventional crytographic system, because the conventional system must implement the privancy and authenticity sequentially with seqarated algorithms and hardware. The OCB-AES processor with area-efficient modular offset generator and tag generator is designed using IDEC Samsung 0.35um standard cell library and consists of about 55,700 gates. Its cipher rate is about 930Mbps and the number of clock cycles needed to generate the 128-bit tags for authenticity and integrity is (m+2)${\times}$(Nr+1), where m and Nr represent the number of block for message and number of rounds for AES encryption, respectively. The OCB-AES processor can be applicable to soft cryptographic IP of IEEE 802.11i wireless LAN and Mobile SoC.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.10
• /
• pp.1247-1255
• /
• 2016

The safety and autonomous flight function of micro UAV or drones is crucial to its commercial application. The requirement of own building stable drones is still a non-trivial obstacle for researchers that want to focus on the intelligence function, such vision and navigation algorithm. The paper present a GCS using commercial drone and hardware platforms, and open source software. The system follows modular architecture and now composed of the communication, UI, image processing. Especially, lane-keeping algorithm. are designed and verified through testing at a sports stadium. The designed lane-keeping algorithm estimates drone position and heading in the lane using Hough transform for line detection, RANSAC-vanishing point algorithm for selecting the desired lines, and tracking algorithm for stability of lines. The flight of drone is controlled by 'forward', 'stop', 'clock-rotate', and 'counter-clock rotate' commands. The present implemented system can fly straight and mild curve lane at 2-3 m/s.

• Journal of Biomedical Engineering Research
• /
• v.19 no.2
• /
• pp.189-198
• /
• 1998

3D medical image reconstruction techniques are useful to figure out complex 3D structures from the set of 2D sections. In the paper, 3D medical image reconstruction system is constructed under PC environment and programmed based on modular programming by using Visual C++ 4.2. The whole procedures are composed of data preparation, gradient estimation, classification, shading, transformation and ray-casting & compositing. Three speed optimization techniques are used for accelerating 3D medical image reconstruction technique. One is to reduce the rays when cast rays to reconstruct 3D medical image, another is to reduce the voxels to be calculated and the other is to apply early ray termination. To implement 3D medical image reconstruction system based on PC, speed optimization techniques are experimented and applied.