• Journal of Chest Surgery
• /
• v.11 no.2
• /
• pp.129-134
• /
• 1978

Two hundred and seventeen patients underwent diagnostic rigid bronchoscopy or bionchofiberscopy to evaluate the cytologic diagnosis in the lung cancer patient at the department of chest surgery of Yon-Sei university, college of the medicine from 1971 to 1977 year. One hundred and twenty cases of these patients were taken rigid bronchoscopy and ninety four cases of these patient were taken bronchofiberscopy. Cytologic examination of the sputum was done in 214 cases and sputum cytology was positive in 50 cases [23.4%]. Rigid bronchoscopy was made in 120 cases and this bronchoscopic cytology including bronchial washing and bronchial biopsy was positive in 34 cases [28.5%]. Bronchofiberscopy was performed in 94 cases and was positive in 45 cases [47.5%]. Histopathologically, 41 cases [43.6%] were epidermoid cell carcinoma, 8 cases [8.5%]of undifferentiated cell type, 12 cases [12.8%]of adenocarcinoma, 8 cases [8.5%]of alveolar cell type, and the 25 cases were undetermined. Cytologic examination of the sputum lacks the accuracy of the bronchoscopies in terms of both localization and accurate histologic indentification of the type of neoplasm. Rigid bronchoscope has the advantage of permitting identification of a tumor in a central location and of providing a sufficient amount of biopsy material for accurate diagnosis of carcinoma. However, it has the disadvantage of limiting examination to the larger, more central portions of the tracheobronchial tree. Bronchofiberscope had the advantage of examine upper lobe as well as other portions of the tracheobronchial tree which could not be visualized with the rigid bronchoscopy. A positive diagnosis in bronchofiberscopy was obtained in the highest rate, 47. 8% [45 cases]. A1 last, if a bronchogenic carcinoma is suspected on the basis of either symptoms of an abnormality on the chest film the diagnostic work-up-sputum cytology, bronchial washing, bronchoscopic biopsy, scalene node biopsy, thoracentesis and mediastinoscopy explothoracotomy etc-should precede in an attempt not only to obtain the higher positive diagnosis but also to obtain a tissue diagnosis and to evaluate the stage of the disease and to ascertain the appropriate mode of therapy.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.3
• /
• pp.457-464
• /
• 2006

Three extracellular proteases (Vpr, peptidase T, and subtilisin) were identified from the culture supernatant of Bacillus subtilis KCTC 3014. All the proteins were partially purified as a mature form by using a DEAE-cellulose ion-exchange column chromatography. Their activities were determined by using zymography and densitometry. The relative molecular masses of Vpr and peptidase T (PepT) were determined to be 68 and 48 kDa by SDS-PAGE and zymography, respectively. However, subtilisin formed a 'binding mode' at the top of the separating gel. After denaturation by boiling at $100^{\circ}C$ for 5 min, its molecular mass was determined to be 29 kDa, whereas its activity was lost. The optimal pH of Vpr, PepT, and subtilisin were 9.0, 6.0-7.0, and 7.0-8.0, respectively. The optimal temperature of Vpr, PepT, and subtilisin was 40, 50, and $40^{\circ}C$, respectively. Inhibitor test revealed that Vpr and subtilisin were serine proteases and that PepT was a metalloprotease. Interestingly, we found that Vpr showed no enzyme activity on a 2DE zymogram gel. Three genes, vpr, pepT, and apr (encoding subtilisin protein), were cloned and their nucleotide and deduced amino acid sequences were determined.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.8
• /
• pp.1163-1178
• /
• 2010

Plasmids play important roles in horizontal gene transfer among Vibrionaceae, but surprisingly little is known about their replication and incompatibility systems. In this study, we successfully developed a bioinformatics-assisted strategy of experimental identification of seven Vibrio plasmid replicons. Comparative sequences analysis of the seven Vibrio plasmid replicons obtained in this study together with eight published Vibrionaceae plasmid sequences revealed replication-participating elements involved in the ColE1 mode of replication initiation and regulation. Like plasmid ColE1, these Vibrionaceae plasmids encode two RNA species (the primer RNA and the antisense RNA) for replication initiation and regulation, and as a result, the 15 Vibrionaceae plasmids were designated as ColE1-like Vibrionaceae (CLV) plasmids. Two subgroups were obtained for the 15 CLV plasmids, based on comparison of replicon organization and phylogenetic analysis of replication regions. Coexistence of CLV plasmids were demonstrated by direct sequencing analysis and Southern hybridization, strongly suggesting that the incompatibility of CLV plasmids is determined mainly by the RNA I species like the ColE1-like plasmids. Sequences resembling the conserved Xer recombination sites were also identified on the CLV plasmids, indicating that the CLV plasmids probably use the host site-specific recombination system for multimer resolution like that used by ColE1-like plasmids. All the results indicated that the 15 plasmids form a new ColE1-like group, providing a basis for the rapid characterization and classification of Vibrionaceae plasmids.

• Journal of the Korean Society of Industry Convergence
• /
• v.14 no.2
• /
• pp.45-52
• /
• 2011

Since the most exclusive machines of the modern industries which require the nano precision rates are evolved from the machine tools, the design of the stable machine tool structure is very critical. Exclusive machines for the modern industries such as semiconductor, solar cell and LED have surface machining processes which are similar to the face cutting and grinding of conventional machine tools. This study was initiated to stabilize a milling machine structure and further to help design those exclusive machines which have similar machining mechanisms. The vibrations inherent to the machine tool structures hurt the precision machining as well as damage the longevity of the structures. There have been numerous researches in order to suppress the vibrations of machine tool structures using the extra modules such as actuators and dampers. In this paper, the dynamic properties are analyzed to obtain the natural frequencies and mode shapes of a machine tool structure which reflect the main reasons of the biggest vibrations under the given operating conditions. And the feasibility of improving the stability of the structure without using any additional apparatus has been investigated with minor design changes. The result of the study shows that simple changes based on proper system identification can considerably improve the stability of the machine tool structure.

• Earthquakes and Structures
• /
• v.12 no.6
• /
• pp.689-697
• /
• 2017

Nowadays, there are a great number of various structures that have been retrofitted by using different FRP Composites. Due to this, more researches need to be conducted to know more the characteristics of these structures, not only that but also a comparison among them before and after the retrofitting is needed. In this research, a model steel structure is tested using a bench-scale earthquake simulator on the shake table, using recorded micro tremor data, in order to get the dynamic behaviors. Beams of the model steel structure are then retrofitted by using CFRP composite, and then tested on the Quanser shake table by using the recorded micro tremor data. At this stage, it is needed to evaluate the dynamic behaviors of the retrofitted model steel structure. Various types of methods of OMA, such as EFDD, SSI, etc. are used to take action in the ambient responses. Having a purpose to learn more about the effects of FRP composite, experimental model analysis of both types (retrofitted and no-retrofitted models) is conducted to evaluate their dynamic behaviors. There is a provision of ambient excitation to the shake table by using recorded micro tremor ambient vibration data on ground level. Furthermore, the Enhanced Frequency Domain decomposition is used through output-only modal identification. At the end of this study, moderate correlation is obtained between mode shapes, periods and damping ratios. The aim of this research is to show and determine the effects of CFRP Composite implementation on structural responses of the model steel structure, in terms of changing its dynamical behaviors. The frequencies for model steel structure and the retrofitted model steel structure are shown to be 34.43% in average difference. Finally, it is shown that, in order to evaluate the period and rigidity of retrofitted structures, OMA might be used.

• Earthquakes and Structures
• /
• v.15 no.3
• /
• pp.335-350
• /
• 2018

This paper presents numerical modelling, modal testing, finite element model updating, linear and nonlinear earthquake behavior of a reinforced concrete building model. A 1/2 geometrically scale, two-storey, reinforced concrete frame model with raft base were constructed, tested and analyzed. Modal testing on the model using ambient vibrations is performed to illustrate the dynamic characteristics experimentally. Finite element model of the structure is developed by ANSYS software and dynamic characteristics such as natural frequencies, mode shapes and damping ratios are calculated numerically. The enhanced frequency domain decomposition method and the stochastic subspace identification method are used for identifying dynamic characteristics experimentally and such values are used to update the finite element models. Different parameters of the model are calibrated using manual tuning process to minimize the differences between the numerically calculated and experimentally measured dynamic characteristics. The maximum difference between the measured and numerically calculated frequencies is reduced from 28.47% to 4.75% with the model updating. To determine the effects of the finite element model updating on the earthquake behavior, linear and nonlinear earthquake analyses are performed using 1992 Erzincan earthquake record, before and after model updating. After model updating, the maximum differences in the displacements and stresses were obtained as 29% and 25% for the linear earthquake analysis and 28% and 47% for the nonlinear earthquake analysis compared with that obtained from initial earthquake results before model updating. These differences state that finite element model updating provides a significant influence on linear and especially nonlinear earthquake behavior of buildings.

• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.1
• /
• pp.38-55
• /
• 2013

This study has been performed to select several indicators of long-range transport process that can be applied to the Northeast Asia. We first classified high air pollution days into long-range transport (LRT) dominant cases and the local emission dominant (LED) cases based on the synoptic meteorological variables including vorticity and geostrophic wind speed/direction at a geopotential level of 850 hPa. LRT cases were further categorized into two types: LRT-I type with air mass pathways from northern China and/or Mongolia, and LRT-II type from central and southern China. In each categorized case, we examined the difference of both measured aerosol optical properties of AERONET at two sites in western Korea, and the simulated characteristics of LRT process by MM5-CMAQ model. We contrasted LRT case with LED case, and then generated the LRT indicators applicable to Northeast Asia. The results showed that fine and coarse modes of LRT-II were relatively smaller than LED and LRT-I cases, respectively. Aerosol size distribution showed significantly higher concentration of fine-mode particle (mainly smoke or urban aerosols) in LED case in comparison with that of LRT groups (LRT-I, II), suggesting the amplitudes fine modes of LRT relative to LED as a possible LRT indicator. From the results of MM5-CMAQ modeling, we concluded that the conversion ratios for sulfur ($F_s$) were the most effective indicators of LRT cases, and the ratio of VOC to NOx and NOx to CO were found to be the second most effective indicators of LED case.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.42 no.4
• /
• pp.31-38
• /
• 2019

The purpose of this study is to provide the priority of the front-loading factors in the design stage of the automotive parts development process in order to efficiently and effectively respond to the demands of the car maker (customer). Front-loading is defined as a strategy in order to improve development performance by shifting the identification and solving of design problems to earlier phases of a product development process. Two approaches of the front-loading are project-to-project knowledge transfer and rapid problem solving. For the study, a survey was conducted on the R&D department in the automobile parts company and analyzed by AHP (Analytic Hierarchy Process) method. The result of the survey shows the cost savings is the highest weight in terms of front-loading effect and in terms of front-loading factors, it gives priorities as "the problems of past project" first, "Design Review" second, "CAE (Computer Aided Engineering)" third, "FMEA (Failure Mode and Effects Analysis)" fourth, "benchmarking" and SR (Sourcing of Requirements). The results of the study will be helpful to provide practical value for improving product design of component development.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3629-3634
• /
• 2013

In this study, an improved method for the quantitative analysis of ginkgolic acids (GAs) in Ginkgo biloba leaf extract was developed. The samples were extracted with a mixture of chloroform and 50 % ethanol, after which the chloroform extract was dried and reconstituted in methanol. GAs with 13:0, 15:1, and 17:1 in the extract were successfully separated within 40 min and determined with high throughput performance using an online column-switching HPLC method using an SP column C8 SG80 ($4.6{\times}150mm$, $5{\mu}m$) and a Cadenza 5CD C18 column ($4.6{\times}150mm$, $3{\mu}m$). The developed HPLC method was validated for Ginkgo biloba leaf extract. The validation parameters were specificity, linearity, precision, accuracy, and limits of detection and quantitation (LODs and LOQs, respectively). It was found that all of the calibration curves showed good linearity ($r^2$ > 0.9993) within the tested ranges. The LODs and LOQs were all lower than $0.04{\mu}g/mL$. The established method was found to be simple, rapid, and high throughput for the quantitative analysis of GAs in ten commercial Ginkgo biloba leaf extract and dietary supplements. The samples were also analyzed in LC-electrospray ionization (ESI) tandem mass spectrometry (MS/MS) - multiple-ion reaction monitoring (MRM) mode to confirm the identification results that were obtained by the column switching HPLC-DAD method. The developed method is considered to be suitable for the routine quality control and safety assurance of Ginkgo biloba leaf extract.

• Journal of Radiation Protection and Research
• /
• v.41 no.2
• /
• pp.117-121
• /
• 2016

Background: Definition and grouping of initiating events (IEs) are important basics for probabilistic safety assessment (PSA). An IE in a spent fuel reprocessing plant (SFRP) is an event that probably leads to the release of dangerous material to jeopardize workers, public and environment. The main difference between SFRPs and nuclear power plants (NPPs) is that hazard materials spread diffusely in a SFRP and radioactive material is just one kind of hazard material. Materials and Methods: Since the research on IEs for NPPs is in-depth around the world, there are several general methods to identify IEs: reference of lists in existence, review of experience feedback, qualitative analysis method, and deductive analysis method. While failure mode and effect analysis (FMEA) is an important qualitative analysis method, master logic diagram (MLD) method is the deductive analysis method. IE identification in SFRPs should be consulted with the experience of NPPs, however the differences between SFRPs and NPPs should be considered seriously. Results and Discussion: The plutonium uranium reduction extraction (Purex) process is adopted by the technics in a model reprocessing plant. The first extraction cycle (FEC) is the pivotal process in the Purex process. Whether the FEC can function safely and steadily would directly influence the production process of the whole plant-production quality. Important facilities of the FEC are installed in the equipment cells (ECs). In this work, IEs in the FEC process were identified and categorized by FMEA and MLD two methods, based on the fact that ECs are containments in the plant. Conclusion: The results show that only two ECs in the FEC do not need to be concerned particularly with safety problems, and criticality, fire and red oil explosion are IEs which should be emphatically analyzed. The results are accordant with the references.