• 한국정밀공학회지
• /
• 제20권1호
• /
• pp.172-178
• /
• 2003

Two types of bolted lap joints, one with a viscoelastic layer and the other without the viscoelastic layer were chosen to analyze the dynamic characteristics of the joints with the mechanical properties of the bolts in the joints are considered as computational variables. The finite element method was used along with the modal testing to verify the PEM model. The results in the bolted lap joints reveal that the higher the Young's modulus for the bolts we use the higher the natural frequencies we obtain fur the joints. However, the natural frequency differences in the first and second mode are not substantial but become noticeable in the higher modes. Lower natural frequencies were obtained for the bolted lap joints with the viscoelastic layer when compared with those of the bolted lap joints without the viscoelastic layer. And the differences in the natural frequencies for the two types of joints are relatively small in the first and second mode whereas in the higher mode the differences become significant. The loss factors were observed to be significant especially in the second mode for the bolted lap joints with the viscoelastic layer.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1302-1307
• /
• 2001

This study identifies the major coupling path by examining the variation of the coupled acoustic modal frequencies and modes. A 1/2-size acryl compartment model is designed and manufactured for the measurement and analysis of coupled acoustic modes. Due to acoustic coupling, a new acoustic mode appears in a low frequency range. This coupling affects only longitudinal acoustic modes of compartment. Experimental result shows that the package tray holes contribute to the coupling much more than the back seat and hole size is an important design factor to control low frequency acoustic modes in the coupled system.

• 대한기계학회논문집A
• /
• 제21권11호
• /
• pp.1885-1895
• /
• 1997

As track density needs to increase to the order of 10, 000 tpi, the suspension has become a critical component in hard disk drives. One of the main obstacles to attain high track density is the structural resonances of the suspension in lateral direction. We investigate the suspension dynamics through the experimental modal analysis and the finite element method. An LDV (Laser Doppler Vibrometer) is employed to measure the response of the suspension which is excited by a shaker and an inpulse hammer for the free condition and the loaded condition, respectively. After comparing the experimental and numerical results, we study how the initial geometry of the bend region affects the suspension dynamics. It is found that the natural frequency of the sway mode decreases as the bend ratio and the bend angle increase. The shape of torsional mode changes as the mass of a slider increases, resulting in a local decrease in the natural frequency.

• 한국정밀공학회지
• /
• 제14권3호
• /
• pp.66-74
• /
• 1997

In a high speed and high precision vertical machining center, chatter vibration is easily generated due to unbalanced masses in rotating parts and changtes of cutting forces. In this paper, modal test is performed to obtain modal parameters of the vertical machining center. In order to predit the cutting force of endmilling process for various cutting conditions, a mathematical model is given and this model is based on chip load, cutting geometry, and relationship between cutting forces and the chip load. Specific cutting constants of the model are obtained by averaging forces of cutting tests. The interactions between the dy- namic characteristics and cutting dynamics of the vertical machining center make the primary and the secondary feedback loops, and we make use of the equations of system to predict the chatter vibration. The chatter prediction is formulated as linear differential-differene equations, and simulated for several cases. Trends of vibration as radial and axial depths of cut are changed are shown and compared.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문집
• /
• pp.1044-1048
• /
• 2002

The experimental modal testing has been carried out for the stator of a generator to confirm the vibrational mode shapes and the corresponding natural frequencies. The model of the stator for the vibration analysis was developed and a series of vibration analyses was carried out. And the properties of the solid element were updated to reduce the differences of the natural frequencies between the measured and the analysed. In the vibration anlyses, the axial, radial and circumferential properties of the solid element were separately varied to take into account the orthotropic effect of the laminated structure and to match the primary modes of the stator core which were extracted from the modal testing. After several attempts to match the measured natural frequencies and model shapes, the properties of the stator model were determined. Comparison of the vibration analyses results based on the determined properties showed fairly good coincidence with the measured data.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1842-1850
• /
• 2017

Reducing the noise and vibration of the BLDC motors is very essential for some special applications. In this paper, a new structural design is introduced to increase the natural frequencies of the stator in BLDC motors as increasing the natural frequencies can reduce the severe effects of the structural resonances, including high levels of noise and vibration. The design is based on placing a single hole on definite regions at the stator cross sectional area (each region contains one tooth and its upper parts in the stator yoke) in an optimum way by which the natural frequencies at different modes are shifted to the higher values. The optimum diameter and locations for the holes are extracted by the Response Surface Methodology (RSM) and the modal analyses in the iterative process are done by Finite Element Method (FEM). Moreover, the motor performance by the optimum stator structure is analyzed by FEM and compared with the prototype motor. Preventing the stator magnetic saturation and the motor cogging torque enhancement are the two constraints of the optimization problem. The optimal structural design method is applied experimentally and the validity of the design method is confirmed by the simulated and experimental results.

• Steel and Composite Structures
• /
• 제14권4호
• /
• pp.367-377
• /
• 2013

Damage in structures often leads to failure. Thus it is very important to monitor structures for the occurrence of damage. When damage happens in a structure the consequence is a change in its modal parameters such as natural frequencies and mode shapes. Artificial Neural Networks (ANNs) are inspired by human biological neurons and have been applied for damage identification with varied success. Natural frequencies of a structure have a strong effect on damage and are applied as effective input parameters used to train the ANN in this study. The applicability of ANNs as a powerful tool for predicting the severity of damage in a model steel girder bridge is examined in this study. The data required for the ANNs which are in the form of natural frequencies were obtained from numerical modal analysis. By incorporating the training data, ANNs are capable of producing outputs in terms of damage severity using the first five natural frequencies. It has been demonstrated that an ANN trained only with natural frequency data can determine the severity of damage with a 6.8% error. The results shows that ANNs trained with numerically obtained samples have a strong potential for structural damage identification.

• Smart Structures and Systems
• /
• 제4권3호
• /
• pp.319-342
• /
• 2008

Identification of the nonlinear hysteretic behavior of a reinforced concrete (RC) bridge pier subjected to earthquake loads is carried out based on acceleration measurements of the earthquake motion and bridge responses. The modified Takeda model is used to describe the hysteretic behavior of the RC pier with a small number of parameters, in which the nonlinear behavior is described in logical forms rather than analytical expressions. Hence, the modified extended Kalman filter is employed to construct the state transition matrix using a finite difference scheme. The sequential modified extended Kalman filter algorithm is proposed to identify the unknown parameters and the state vector separately in two steps, so that the size of the problem for each identification procedure may be reduced and possible numerical problems may be avoided. Mode superposition with a modal sorting technique is also proposed to reduce the size of the identification problem for the nonlinear dynamic system with multi-degrees of freedom. Example analysis is carried out for a continuous bridge with a RC pier subjected to earthquake loads in the longitudinal and transverse directions.

• Structural Engineering and Mechanics
• /
• 제25권1호
• /
• pp.1-20
• /
• 2007

Dynamic behaviors of the contact surface between ball and raceway in a guideway mechanism vary with the applied loads and hence affect the mechanical responses of machine tools. The study aims to investigate the nonlinear characteristics of dynamic behaviors at the rolling contact interface in linear guideway mechanisms. Firstly, analytical method was introduced to understand the contact behaviors based on Hertz contact theory in a point-to-point way. Then, the finite element approach with a three-dimensional surface-to-surface contact model and appropriate contact stiffness was developed to study the dynamic characteristics of such linear guideways. Finally, experiments with modal test were conducted to verify the significance of both the analytical and the numerical results. Results told that the finite element approach may provide significant predictions. The study results also concluded that the current nonlinear models based on Hertz's contact theory may accurately describe the contact characteristic of a linear guideway mechanism. In the modal analysis, it was told that the natural frequencies vary a little with different loading conditions; however, the mode shapes are changed obviously with the magnitude of applied loads. Therefore, the stiffness of contact interface needs to be properly adjusted during simulation which may affect the dynamic characteristics of the machine tools.

• 한국철도학회논문집
• /
• 제16권1호
• /
• pp.1-6
• /
• 2013

본 연구에서는 복합소재 전동차용 대차프레임에 적용되는 4매 주자직 유리섬유/에폭시 복합소재에 대한 고유진동 특성과 주파수에 따른 감쇠특성을 평가하였다. 이를 위해 오토클레이브 성형을 통해 길이와 두께가 다른 유리섬유/에폭시 빔 시편을 제작하였다. 시험결과 감쇠비의 최대값은 최소 고유진동수에서 발생하였다. 또한, 주파수가 증가함에 따라감쇠비는 지수 함수적으로 임계치까지 감소하였다. 이후에는 주파수에 따라 증가하는 경향을 보였다.