• Journal of the Korea Concrete Institute
• /
• v.17 no.1 s.85
• /
• pp.141-147
• /
• 2005

The development of automobile, vessel, rail road, and machine industry leads an increase of foundry production used as their components, which cause a by-product, waste foundry sand (WFS). The amount of the WFS produced in Korea is over 700,000 tons a year, but most WFS has been buried itself and only $5{\~}6\%$ WFS is recycled as construction materials. Therefore, it is necessary for most WFS to research other ways which can be used in a higher value added product. The study on recycling it as a fine aggregate for concrete or green sand has been in progress in America and Japan since 1970s and 1980s respaectively. In this study, two types of WFS were used as a fine aggregate for concrete. Nine types of concrete aimed at the specified strength of 30 MPa were mixed with washed seashore coarse sand in which salt was removed, and WFS and then appropriate mixture proportion of concrete was determined. Moreover, basic properties such as air contents, setting time, bleeding, workability and slump loss of the fresh concrete with WFS were tested and compared with those of the concrete mixed without WFS. In addition, both compressive strength of hardened concrete at each ages and tensile strength of it at the age of 28 days were measured and discussed.

• Tribology and Lubricants
• /
• v.28 no.2
• /
• pp.47-55
• /
• 2012

Generally, to product multi-grade oil like engine oil, a sort of mineral base oil is mixed with a fundamental additive package liquid and a polymer liquid as viscosity index improver in order to improve the lubricating property of base oil. That is, engine oil is the mixture of more than two fluids. Specially, a polymeric type liquid cannot be seen as the linear viscosity like Newtonian fluids. In this research, by using the governing equation describing non-Newtonian hydrodynamic lubrication related with the mixture of incompressible fluids based on the principle of continuum mechanics, it will be compared the bearing performance between the mixture of each liquid to be blended and multi-grade engine oil as a single fluid in a high speed hydrodynamic journal bearing. Further, it is to be found the way estimating the performance of the blended multi-grade engine lubricant in a journal bearing in advance before blending by using the physical properties of mineral base oil, fundamental additive liquid and polymer liquid of viscosity index improver. So, it can be reduced the number of trial and error to get the wanted lubricant by selecting the proper volume fraction of each liquid to satisfy the expected performance and estimating in advance the performance of various multi-grade oils before blending. Therefore, it can be shorten the developing time and saved the developing cost.

• Journal of Pharmaceutical Investigation
• /
• v.21 no.3
• /
• pp.171-177
• /
• 1991

A reverse-phase, ion-pair high performance liquid chromatographic (HPLC) method for the simultaneous quantative determination of pyridostigmine and its hydrolytic product, 3-hydroxy-N-methylpyridinium (HMP), is descrihed, The assay of pyridostigmine and HMP was linear in the range of amount from 24 to 60 mg/tablet and from 2.4 to 12.0 mg/tablet, respectively, with coefficient of variation (C.V.) of 0.05-0.12% (n=7) and 0.25-0.52% (n=5), respectively, and applicable conveniently even in the case of the mixture of pyridostigmine and HMP. Meanwhile, the conventional UV method gave inaccurate results for the aged pyridostigmine tablets. In the extraction of pyridostigmine from tablets prior to be assayed by HPLC, methanol was found to be more effective than ethanol or distilled water. Multiple extraction (four times) with methanol resulted in the full recovery of pyridostigmine, whereas ethanol gave 95% recovery even after four times extraction. Based on these results. the present method would be very useful for the accurate determination of pyridostigmine in the aged pyridostigmine tablets.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.41 no.7
• /
• pp.975-981
• /
• 2012

Setting is an important process for the control of surimi quality in industry because it can improve the gel texture and water-holding capacity of surimi-based products. Therefore, the effect of setting on giant squid surimi-based product was analyzed via a mixture model. Konjac flour and microbial transglutaminase were used as texture enhancers. Both texture enhancers improved the texture and water retention ability (WRA) of giant squid surimi-based products, while decreasing the whiteness. Setting also improved the gel texture and WRA, while having no effect on the whiteness. Based on the sensory evaluation, the product with gel texture enhancers was better than the control and similar to commercial surimi products. Therefore, the applications of gel texture enhancers and setting are very important for the manufacture of giant squid surimi-based products.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.1
• /
• pp.50-57
• /
• 2016

We studied the Lab-scale process for the development of DNAM in aspect of safety and overall efficiency. Melamine is used for starting material of process, DNAM was synthesized by oxidation and nitration reaction. In order to optimize the process parameters with the product in higher yield and purity, a systematic study with variation of different parameters like molar ratio of nitrating mixture, conditioning time and order of reactant was carried out. The optimized reaction conditions for the synthesis of DNAM were : conditioning time of $3{\pm}3.5$ hour and nitrating mixture in 1:1.4 molar ratio. In order to proceed a stable reaction, melamine was added with enough time to relieve reaction heat. From these reaction condition, DNAM could be obtained in a yield of more than 60%.

• Korean Journal of Soil Science and Fertilizer
• /
• v.38 no.1
• /
• pp.45-51
• /
• 2005

As a silicate source to rice, a coal ash (50%) was mixed with a phosphogypsum (hereafter, gypsum, 50%). Field experiments were carried out to evaluate rice (Oryza sativa) productivity in silt loam (SiL) to which 0, 20, 40 and $60Mg\;ha^{-1}$ of the mixture were added. The mixture increased rice yield and showed the highest yields following the addition of $30Mg\;ha^{-1}$. The mixture did not result in an excessive uptake of heavy metals by the rice grain. The mixture improved available silicate and phosphate and exchangeable calcium contents in soil. The available boron content in soil increased with the mixture application levels up to $1.42mg\;kg^{-1}$ following the application of $60Mg\;ha^{-1}$, but boron toxicity in rice was not found. It is concluded that the coal ash and gypsum mixture could be a good alternative to inorganic soil amendments to restore the soil nutrient balance in paddy soil.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.8
• /
• pp.1371-1379
• /
• 2003

RP&M (Rapid Prototyping and Manufacturing) is the most appropriate technology for the small-lot production system, because the production cycle is getting shorter owing to various needs of the consumer. In this paper, rapid tooling technology is applied to the casting process. The casting process has the ability to reflect complicated shapes in one process. But it has not been widely used to make a die and mold because of the poor surface quality caused by air bubbles on the surface of the casting product. In this study, the porous casting mold is fabricated from a mixture of plaster and water-soluble binder. The porous casting mold can improve the characteristics of casting products with the help of the vacuum sealed casting process. The vacuum sealed casting process is an advanced technology that removes the air bubbles between the porous casting mould and the liquid metal, thus making the surface of the casting product finer. The purpose of this paper is to develop a high quality shoe mold using porous casting mold and to apply the RP&M technology to the shoe industry.

• Development and Reproduction
• /
• v.24 no.1
• /
• pp.1-17
• /
• 2020

Phthalates and those metabolites have long history in industry and suspected to have deficient effects in development and reproduction. These are well-known anti-androgenic chemicals and many studies have examined the effects of these compounds on male reproduction as toxins and endocrine disruptors. Uterus is a key organ for proper embryo development, successful reproduction, and health of eutherian mammals including women. To understand the effects of the phthalate, the horizontal approach with a whole group of phthalate is best but the known phthalates are huge and all is not uncovered. Di-(2-ethylhexyl) phthalate (DEHP) is the most common product of plasticizers in polymer products and studied many groups. Although, there is limited studies on the effects of phthalates on the female, a few studies have proved the endocrine disrupting characters of DEHP or phthalate mixture in female. An acute and high dose of DEHP has adverse effects on uterine histological characters. Recently, it has been revealed that a chronical low-dose exposing of DEHP works as endocrine disrupting chemicals (EDC). DEHP can induce various cellular responses including the expression regulation of steroid hormone receptors, transcription factors, and paracrine factors. Interestingly, the response of uterus to DEHP is not monotonous and the exposed female has various phenotypes in fertility. These suggest that the exposing of DEHP may causes of histological modification in uterus and of disease in female such as endometriosis, hyperplasia, and myoma in addition to developmental and reproductive toxicity.

• BMB Reports
• /
• v.33 no.4
• /
• pp.353-357
• /
• 2000

A new assay method of ${\alpha}-Oxidase$ (fatty acid : oxygen dioxygenase, 1-decarboxylating) was developed using a bioluminescence reaction system of marine luminous bacterium, Photobacterium phosphoreum. ${\alpha}$-Oxidase was isolated from a cucumber (Cucumis sativus). Pentadecanoic acid was used as a substrate, and the product, tetradecanal, was analyzed with a bacterial luciferase-coupled reaction. Initial light intensity was directly related to the concentration of tetradecanal in the range of 1 nM to 10 ${\mu}M$. Optimal pH and temperature were 7.5 and $25^{\circ}C$, respectively. Optimal pentadecanoic acid concentration in a standard assay of ${\alpha}$-oxidase was 0.1 mM. The Km value of pentedecanoic acid was $85{\mu}M$. This method is straightforward, rapid, convenient, and easy. Its needs no treatment or extraction of reaction mixture.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.6
• /
• pp.16-23
• /
• 2013

It is important that proving ground damage is correlated with target customer usage. This paper describes the test mode for durability test of active suspension control system for proving ground correlation and optimization. Acceleration, strain, wheel force and other types of data are collected on a vehicle as it traverses different proving ground surfaces. The primary objective of the analysis is to determine which mixture of proving ground surfaces offers the best representation of customer usage while minimizing the total test time. And durability testing offers the best way to assess the capability of a product to reach its reliability target. The test should be representative of the real environmental load and replicate the same customer usage.