• Resources Recycling
• /
• v.30 no.1
• /
• pp.53-59
• /
• 2021

Waste vinyl generated from household waste has been used as a solid refuse fuel (SRF) due to the presence of impurities such as soil, metal, and glass; however, the amount of SRF used has been decreasing owing to recent environmental problems, thereby necessitating the need for recycling. In this study, the mixed recycled raw material produced from household waste vinyl and polyethylene (PE) single recycled raw material produced from agricultural waste vinyl were examined. Raw material analysis revealed that waste vinyl was mainly composed of polyethylene, and approximately 2% of ash remained in the mixed recycled raw material, whereas no ash was found in the PE single recycled raw material. In addition, the analysis of tensile strength according to the mixing ratio of the two recycled raw materials revealed that the highest tensile strength was approximately 16 MPa under the heat treatment temperature of 200 ℃, compression pressure of 30 MPa, and a mixing ratio of 3:7 (mixed:PE single). In addition, the highest bending strength was approximately 39 MPa under the heat treatment temperature of 200 ℃, compression pressure of 30 MPa, and a mixing ratio of 3:7 (mixed:PE single). Therefore, the possibility of recycling waste vinyl was suggested by investigating the change in strength characteristics according to the mixing ratio of the recycled raw materials.

• Applied Chemistry for Engineering
• /
• v.17 no.6
• /
• pp.614-618
• /
• 2006

Recycling of asphalt including shingle is much important for economic aspects such as a decrease of treatment cost. This research was carried out in order to process the recycled shingle to asphalt concrete which is a pavement material. Pure asphalt and the mixture of recycled asphalt were tested in terms of the thermal characteristics, viscosity, and penetration. DSC analysis indicates that the thermal characteristics of separate shingle showed similar properties regardless of processing conditions. Melting of asphalt separated from shingle occurred at $170^{\circ}C$. The viscosity and penetration of the 1~5 wt% of mixed recycling asphalt and raw material asphalt are suitable for the pavement material standard.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.445-451
• /
• 2019

In this study, we evaluated the durability of concrete produced with recycled polymer that could replace synthetic polymer, which is the main raw material of bridge deck concrete pavement. As a result of the slump and air content test, the requirements of the Korea Highway Corporation Standard were satisfied with all mixing conditions. The slump was lowered when incorporating the recycled bio-polymer, compared to other mix proportions concrete. In contrast, the compressive strength was increased by 6.3~24.4% when the recycled bio-polymer was mixed, compared to the concrete produced with synthetic polymer. It should be noted that the compressive strength was lowered when synthetic polymer was added to concrete mixture. Durability test results showed the best durability when incorporating synthetic polymer. The durability of concrete also increased as the amount of recycled bio-polymer increased, however, the impact was slightly smaller than that of synthetic polymer.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.4
• /
• pp.395-403
• /
• 2020

CaO-based by-product, which consist of CaO, SO3, Al2O3 and so on, has being used to raw materials of CaO compound. When It was applied to recycling water of remicon, concrete performance can be enhanced because hydration reaction of powder material is accelerated. In this study, activated-sludge, which was putted desulfurization gypsum of CaO-based in recycling water, was manufactured to verify effect of them, and then they was investigated by characteristics of redy-mixde concrete. As a result of concrete tests, it was confirmed that there is no problem of strength or drying shrinkage while ensuring workability. Therefore, the possibility of specific application using activated sludge was confirmed.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.47 no.2
• /
• pp.34-41
• /
• 2015

Recovered paper has been widely used as a main raw material of papermaking in Korea. Recycling of recovered paper helps to reduce production cost and preserve an environment. To recycle recovered paper efficiently, de-inking is a key process in recycling mills. De-inking process would be affected by various influencing factors such as the type of de-inking agent, mixed ratio of recovered paper, season, and process conditions. In this study, fatty acid and nonionic surfactant were used as the de-inking agent in froth-flotation process of mixed recovered paper. De-inking properties of mixed recovered paper were investigated according to the addition level of each chemical. Nonionic surfactant had a small effect on de-inking efficiency of mixed recovered paper due to decreased reject. As the additional level of fatty acid increases, fragmented ink particles increased and then optical properties of recycled paper decreased because fragmented ink particles adsorbed onto the fiber surface.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.1
• /
• pp.92-99
• /
• 2021

CaO-based by-products composed of CaO, SO3, Al2O3, etc. are generally used as raw materials for CaO compounds. When applied to the recovered water of ready-mixed concrete, the hydration reaction of the powder material is accelerated and concrete performance can be improved. In this study, activated sludge was prepared to apply to the recovered water of ready-mixed concrete by mixing CaO-based hot-rolled slag(C12A7) in the recycling water of ready-m ixed concrete. Cem ent paste setting time and mortar compressive strength performance tests confirmed the effect on the hydration reaction. Therefore, the possibility of concrete application using activated sludge was confirmed.

• Microbiology and Biotechnology Letters
• /
• v.22 no.1
• /
• pp.80-84
• /
• 1994

In order to induce the rapid alcohol fermentation through the increases of the cell density in a continuous alcohol fermentation of naked barley, the single-cultivation with S. cerevisiae IS-019(SCM, ordinary control), mixed-cultivation with Saccharomyces uvarum IS-026 having a flocculent ability and S. cerevisiae IS-019(MCM), and mash recirculation by single-cultivation of S. cerevisiae IS-019(MRM) modes were investigated. The cell mass in the mixed-cultivation mode was about 10% higher than that of ordinary control but the final alcohol yield was slightlyl decreased. When recycled the mash with the flow rate of 7 l/h from V$_{6}$ to V$_{5}$ fermentors under the ordinary control, the cell density was distributed at 140~170$\times $10$^{6}$ cell/ml depending upon the fermentorsorders, higher about 20% than that of the ordinary control. Under these conditions the alcohol productivity of the maximum and the overall was 12.16 g/l$\cdot $h with an alcohol of 7.6% at the V$_{5}$ fermentor and 1.19 g/l$\cdot $h with an alcohol of 8.94%, respectively. For higher cell mass it was more effective to apply the mash recirculation mode with the single-cultivation of S. cerevisiae IS-019 in a pilot scale multi-stage CSTR.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.4
• /
• pp.123-130
• /
• 2011

In the precedent study it was presented that the comparison of thermal resistivity using various backfill materials including river sand regarding water content, dry unit weight and particle size distribution. Based on the precedent study, this study focused on developing the optimized backfill material that would improve the power transfer capability and minimize the thermal runaway due to an increase of power transmission capacity of underground power cables. When raw materials, such as river sand, recycled sand, crush rock and stone powder, are used for a backfill material, they has not efficient thermal resistivity around underground power cables. Thus, laboratory tests are performed by mixing Fly-ash, slag and floc with them, and then it is found that the optimized backfill material are required proper water content and maximum density. Through various experimental test, when coarse material, crush rock, is mixed with recycled sand, stone powder, slag or floc for a dense material, the thermal resistivity of it has $50^{\circ}C$-cm/Watt at optimum moisture content, and the increase of thermal resistivity does not happen in dry condition. The result of experiments approach the optimization of the backfill materials for underground power cables.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.38 no.3 s.116
• /
• pp.72-78
• /
• 2006

The extraction properties of the biological waste originated from the Tobacco industry were evaluated. The biological waste have been recycled and transformed into a valuable material, so called a reconstituted tobacco sheet(Recon) by the papermaking process. In this process, The mechanical extraction process, which divides the mixed raw material slurry into the soluble stock and the insoluble stock, could affect not only the quality of final Recon product but also the productivity of whole Recon making process. This study investigated the effects of the extraction process on the slurry properties in detail. In order to quantify the amounts of the solubles which resided in the insoluble fibers, the washing treatment of the stock before and after squeezing process was applied. The amounts of the residual solubles showed little changes according to each stage of the extraction process. The fractionation of the slurry showed the difference in the amount of soluble in the stock depending on the size of the biological waste. After the extraction process, the bigger size fiber portion contained about 19%(by weight) in soluble after pressing but the smaller size fiber portion 9% in soluble. The fractionation ratio of the stocks also was changed by the screw press process, which could demonstrate the physical effects of the mechanical extraction.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.4
• /
• pp.383-388
• /
• 2019

The present study evaluated experimentally the effects of the type and content of plastic fine aggregates on cement mortar in order to utilize waste platics as raw materials of concrete. The two kinds of plastics, LLDPE and HDPE were used, and the mixing rate of plastic fine aggregates was increased 0, 25, 50, 75, 100%. The mortar of LLDPE fine aggregate and HDPE fine aggregate showed similar tendency in flow and material separation resistance, density and water absorption, compressive strength and flexural strength by age. The flowability of mortar mixed with plastic fine aggregates was increased up to 50% but decreased at 75% or more. The material separation resistance of mortar with plastic fine aggregates was also dramatically decreased. On the other hand, due to the low density of plastics, the density of mortar decreased with the mixing of plastic fine aggregates. Due to the low adhesion between plastic fine aggregates and cement, the compressive strength by age was decreased in proportion to the mixing ratio of plastic aggregate, but the flexural strength of each age decreased with maintaining a certain level at 50% or more of plastic fine aggregate content.