• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.06a
• /
• pp.103-117
• /
• 2002

During the installation of drilled shafts in very soft ground, to keep the pile shape and to central concrete quality, casing method (wrinkled pipe and embedded steel pipe) and non-casing method have been used. In the construction cost, non-casing method was the most economical. When the wrinkled pipe and the embedded steel pipe casing method are used, an increase of 133% and 123% in the construction cost could be seen. When concrete for drilled shaft was placed under groundwater, underwater unseparation concrete would be used to restrain the concretes's material separation and to control the concrete quality. On the condition of required unseparable and (lowing property was assured, use of less amount of mixed material and flowing material must be recommended.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.513-516
• /
• 2001

In this study, the properties of MCMB anode Mixed with KCF were evaluated. KCF material was used as not only conducting agent but also active material. The Electric conductivity of MCMB and KCF were 23.7S/cm and 45.8S/cm. Characteristics of anode with different KCF contents were the best effect at 2wt%. The 1st Ah efficiency of cells were increased with increment of KCF contents. The internal resistance and the rate capability were 1.59Ω and 135mAh/g at 2C. The discharge capacity was gradually faded with the charge-discharge cycling to about 50th cycles.

• Textile Coloration and Finishing
• /
• v.34 no.4
• /
• pp.250-260
• /
• 2022

In this research, a high-elasticity acrylic emulsion binder with core-shell polymerization and self-crosslinking system is mixed with a flame-retardant water-dispersed polyurethane (PUD) binder. In addition, finite element analysis was conducted through virtual engineering software ANSYS by applying three representative nonlinear material models. The most suitable nonlinear material model was selected after the relative comparison between the actual experimental values and the predicted values of the properties derived from simulations. The selected nonlinear material model is intended to be used as a nonlinear material model for computational simulation analysis that simulates the experimental environment of the vibration test (ASTM E1399) and the actual fire safety test (ASTM E1966). When the mass fraction of thermally expandable graphite was 0.7%, the thermal and physical properties were the best. Among the nonlinear material models, the simulation result of the Ogden model showed the closest value to the actual result.

• The Journal of Engineering Geology
• /
• v.20 no.3
• /
• pp.297-310
• /
• 2010

This study represents basic research into the utilization of mixed ash (fly ash and bottom ash) from the ash pond of the Taean Thermal Power Plant as a construction material. We conducted physical and mechanical experiments on the mixed ash and examined its engineering characteristics in terms of its use as a material for road landfill and structure backfill. We evaluated the physical and chemical characteristics of the ash by performing tests to determine specific gravity, maximum and minimum density, liquid limit and plastic limit, grain size distribution, composition (by X-ray diffraction), and loss on ignition. We also evaluated the mechanical characteristics by testing for permeability, compaction, CBR, and tri-axial compression. The experiments on the mixed ash yielded a specific gravity of 2.18-2.20, dry density of $9.38-13.32\;kN/m^3$, modified CBR of 16.5%-21%, permeability coefficient of 1.32 to $1.89-10^{-4}cm/sec$, and drained friction angle of $36.43^{\circ}-41.39^{\circ}$. The physical and mechanical properties of the mixed ash do not meet the quality standards stipulated for road landfill and structure backfill materials. Mixed ash with a high content of fly ash failed to meet some of the quality standards. Therefore, in order to utilize the mixed ash as a material for road landfill and structure backfill, it is necessary to improve its properties by mixing with bottom ash.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.04a
• /
• pp.31-32
• /
• 2008

The structure of OLEDs with conventional heterostructure consists of anode, hole injection layer, hole transport layer, light-emitting layer, electron transport layer, electron injection layer, and cathode. NPB used as a hole transport layer and DPVBi used as a blue light emitting layer were graded-mixed at selected ratio. Interface at heterojunction between the hole transport layer and the elecrtron transport layer restricts device's stability. Mixing of the hole transport layerand the emitting layer removes abrupt interface between the hole transport. layer and the electron transport layer. The stability of OLED with graded mixed-layer developed in this study was improved.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.6
• /
• pp.491-496
• /
• 2010

The relaxation behavior of aligned electric dipoles in a mixed polymer of P2ANS with P(VDF-TrFE) is studied with optical second harmonic generation (SHG). In this work, a macroscopic noncentrosymmetry of the spin coated film was achieved by an electrical poling. The relaxation of induced polar order of nonlinear optic(NLO) chromophores after poling leads to an insufficient long-term stability of NLO properties. In this work, we develop a new technique to suppress such kind of dipole relaxation in a poled polymer. We found that the poled dipoles in a NLO polymer were effectively immobilized by the internal electric field created by a thermally annealed ferroelectric polymer. The long-term stability in a mixed system of NLO polymer/ferroelectric polymer was successively accomplished by a series of thermal treatments applied to the mixed polymer system at a temperature of $140^{\circ}C$ for at least 1hour after poling.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.2
• /
• pp.14-20
• /
• 1998

Automatic finishing process requires the development of high efficient and precision abrasive machining method for dies and molds. This study describes the evaluation of the finishing characteristics, such as surfrace roughness, topography and material removal depth of the electrolytic mixed abrasive machining methods. Experimental setup is composed of 3 axis machining center, a newly developed finishing attachment with constant pressure, electrode and electrolytic bath. Finally, we achieved a successful result that surface roughness is $0.01\mu$m Ra and material removal depth is $120\mu$m using electrolytic(0.8A. 30V) mixed abrasive (#400 CBN, #320 SiC) machining method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1042-1045
• /
• 2006

The electrical and optical properties of electrophosphorescent organic light-emitting diodes (OLEDs) with modified hole blocking layer (HBL) were investigated. Well-known 2,9-dimethyl-4,7- diphenyl-1,10-phenanthroline (BCP) HBL is mixed with electrophosphorescent host material (4,4'-N,N'- dicarbazole-biphenyl: CBP) or electrophosphorescent dopant material (fac-tris(2-phenylpyridine) iridium: $Ir(ppy)_3$) or both. The highest external quantum efficiency was obtained in the device with $BCP-CBP-Ir(ppy)_3$ mixed HBL and we attribute this result to the additional charge recombination in mixed-HBL.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.486-489
• /
• 2002

Temperature(T) dependence of the sheet resistance( $R_{$\square$}$) has been investigated on the c-axis oriented thin films of the (Bi2212/Bi2201) mixed crystal with different molar fractions. The $R_{$\square$}$-T superconducting characteristic deteriorated with reduction of the Bi2212 fraction, and almost disappears at 48 mol% where a superconductor-to-insulator transition took place, with the resistance on the normal state, RN, reaching 4.l㏀ at 80 K. This $R_{N}$ value is close to the universal quantum number, h/(2e)$^2$≡6.5㏀ predicted by the Kosterlitz-Thouless(KT) transition theory. The $R_{$\square$}$-T characteristics of the 48 mol% thin film can be elucidated as a competitive process of KT transition brought about by charge or vortex in the two-dimensional layer structure.e.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1160-1166
• /
• 2006

Maxwell-displacement-current (MDC) measuring technique has been applied for the investigation of monolayers of poly(vinyl alcohol)s bearing azobenzene side-chains (6Az5PVA) mixed with p-pentyl-p'-cyano-biphenyls (5CBs) on a water surface. For mixed monolayers containing trans-form 6Az5PVA and LCs, displacement current due to photo isomerization was not generated with alternative photo-irradiation with UV and svisible light. In contrast, for mixed monolaters containing cis-form 6Az5PVA and LCs, displacement current was generated. Finally, it was found that the alignment layers deposited in cis-form could photoregualte the orientation of LCs.