• Archives of Plastic Surgery
• /
• 제50권1호
• /
• pp.42-48
• /
• 2023

Background The temporalis muscle flap transfer with fascia lata augmentation (FLA) is a promising method for smile reconstruction after facial palsy. International literature lacks a detailed anatomical analysis of the temporalis muscle (TPM) combined with fascia lata (FL) augmentation. This study aims to describe the muscle's properties and calculate the length of FL needed to perform the temporalis muscle flap transfer with FLA. Methods Twenty nonembalmed male (m) and female (f) hemifacial cadavers were dissected to investigate the temporalis muscle's anatomy. Results The calculated minimum length of FL needed is 7.03cm (f) and 5.99cm (m). The length of the harvested tendon is 3.16cm/± 1.32cm (f) and 3.18/± 0.73cm (m). The length of the anterior part of the temporalis muscle (aTPM) is 4.16/± 0.80cm (f) and 5.30/± 0.85cm (m). The length of the posterior part (pTPM) is 5.24/± 1.51cm (f) and 6.62/± 1.03cm (m). The length from the most anterior to the most posterior point (aTPMpTPM) is 8.60/± 0.98cm (f) and 10.18/± 0.79cm (m). The length from the most cranial point to the distal tendon (cTPMdT) is 7.90/± 0.43cm (f) and 9.79/± 1.11cm (m). Conclusions This study gives basic information about the temporalis muscle and its anatomy to support existing and future surgical procedures in their performance. The recommended minimum length of FL to perform a temporalis muscle transfer with FLA is 7.03cm for female and 5.99cm for male, and minimum width of 3 cm. We recommend harvesting some extra centimeters to allow adjusting afterward.

• 한국환경과학회지
• /
• 제14권1호
• /
• pp.33-40
• /
• 2005

The size of minimum order stream has a very sensitive effect on runoff analysis model using the divergence characteristic of stream. Therefore, in this study, the threshold area of minimum order stream has been examined the change characteristic of topographical parameters. The subject basin of the research was the upper basin of the Kumho water gage station which is located in the middle of the Kumho river. The 1:25,000 numerical geography which was constructed $10{\times}10m$ mesh was used. The range of investigation of topographical parameters are number of stream order, length, area, slope, basin relief, sinuosity ratio, drainage density and total stream length etc. It was found from the result of analysis that the threshold value of minimum order stream has a very big effect on topographical parameters of basin. It was found that the threshold area of minimum ord er stream revealed under $0.10km^{2}.$ Furthermore, the parameters showed a serious change except for over $0.10km^{2}.$

• Journal of Biosystems Engineering
• /
• 제37권2호
• /
• pp.90-99
• /
• 2012

Purpose: This study was conducted to investigate the optimal sorting factors in establishing an efficient sorting technology for brown rice. Methods: The brown rice varieties used in this study were Il Pum, Chu Cheong, Dong Jin, Un Gwang, Nam Pyeong, and Dae An. These were classified into whole grain, unriped grain, and green dead rice. The shape factors were analyzed based on length, width and thickness of the grains. Results: The results revealed that the maximum length among whole grain, unriped grain, and green dead rice was observed in Dae An variety while Chu Cheong variety showed the minimum. Further more, Il Pum brown rice showed the maximum width while Dong Jin variety showed the minimum. In the case of thickness, the maximum was observed in Un Gwang variety and that of the minimum among Nam Pyeong variety for both whole grain and unriped grain. Conclusions: The length and width can be used as determinants in sorting factors of whole grain and green dead rice, and the thickness can be considered as optimum sorting factor of whole grain and unriped grain.

• Asian-Australasian Journal of Animal Sciences
• /
• 제5권2호
• /
• pp.375-382
• /
• 1992

The effect of certain factors such as sex of calf, status of buffalo, season of calving, parity and sire on lactation length and total lactation yield was studied in 391 Nili-Ravi buffaloes. The average lactation length was $301.73{\pm}1.87$ (mean $\pm$ SE) days with a range of 181 to 505 days whereas the average lactation yield was $2031.08{\pm}19.16kg$ and ranged from 1023 to 6535 kg for 984 lactations. The differences in the means of lactation length and lactation yield due to the sex of calf were significant (p<0.05). The status of buffaloes had a significant (p<0.05) effect on lactation length but its effect on lactation yield was non-significant. The season of calving had no effect on lactation length but it influenced the lactation yield significantly. The milk yield was highest ($2150.81{\pm}43.52kg$) in buffaloes which calved in spring and lowest ($1959.92{\pm}30.83kg$) in autumn. The effect of parity on both traits under study was significant (p<0.01). The maximum and minimum lactation lengths of $309.82{\pm}3.96$ and $284.16{\pm}7.17$ days were observed in the first and sixth lactations, respectively. The milk yield was maximum ($2150.38{\pm}58.79kg$) in the seventh lactation and minimum (1818.31 60.04 kg) in the sixth lactation. The influence of sire was significant on lactation length (p<0.05) and milk yield (p<0.01).

• Tribology and Lubricants
• /
• 제25권3호
• /
• pp.157-162
• /
• 2009

In this paper, the hydrodynamic pressure and minimum oil film thickness of a pin bush bearing for a connecting rod have been analyzed as functions of the number of oil grooves and an arc length of oil grooves. The lubrication characteristic of a pin bush is governed by oil groove design factors, which are considered in this study. The most influential design parameter is a number of oil grooves, which is three oil grooves with an arc length of oil groove, 1/6($60^{\circ}$). This means that oil groove with a long arc length of a pin bush does not contribute to the hydrodynamic pressure development. Thus the optimal design of a pin bush is necessary with an increased number of oil grooves and a reduced arc length.

• 대한방사선기술학회지:방사선기술과학
• /
• 제31권3호
• /
• pp.277-285
• /
• 2008

MRI를 이용하여 정상의 뇌량 크기를 측정한 결과 다음과 같은 결론을 얻었다. 1. 전체 대상자의 부위별 평균, 최소, 최대 1) Anteroposterior length는 평균 69.30mm, 최소 50.70mm, 최대 80.40mm이었다. 2) Diameter of genu는 평균 11.93mm, 최소 6.00mm, 최대 18.50mm이었다. 3) Diameter of mid body는 평균 7.00mm, 최소 3.40mm, 최대 10.40mm이었다. 4) Diameter of narrowing portion은 평균 4.51mm, 최소 0.80mm, 최대 9.50mm이었다. 5) Diameter of splenium은 평균 12.17mm, 최소 6.90mm, 최대 17.20mm이었다. 2. 전체 대상자의 성별에 따른 부위별 비교 1) Anteroposterior length는 남자가 여자보다 컸으며, 성별에 따라 유의미한 차이를 보였다. 2) Diameter of genu와 diameter of mid body, diameter of narrowing portion은 남자가 여자보다 컸으나 유의미한 차이는 아니었다. 3) Diameter of splenium은 남자가 여자보다 컸으며, 통계적으로도 유의미한 차이를 보였다. 3. 전체 대상자의 부위별 상관관계 1) Diameter of genu는 anteroposterior length와 통계적으로 유의미한 정적 상관관계를 보였다. 2) Diameter of mid body는 anteroposterior length, diameter of genu와 통계적으로 유의미한 정적 상관 관계를 보였다. 3) Diameter of narrowing portion은 anteroposterior length와 통계적으로 유의미한 상관관계를 보이지 않았으나 diameter of genu, diameter of mid body와 통계적으로 유의미한 정적 상관관계를 보였다. 4) Diameter of splenium은 anteroposterior length와 diameter of genu, diameter of mid body, 그리고 diameter of narrowing portion과 통계적으로 유의미한 정적 상관관계를 보였다.

• 정보처리학회논문지A
• /
• 제17A권5호
• /
• pp.213-220
• /
• 2010

본 논문에서는 스타이너 트리를 이용하여 최소 길이로 입력 선분들을 모두 연결하는 방법을 제안한다. 선분은 통신선, 도로 및 철도망 또는 움직이는 물체의 궤적 등으로 변환될 수 있다. 본 논문에서 제안된 방법은 이러한 선분들을 최소 비용으로 연결하는 응용 등에 활용가능하다. 입력 선분의 수와 각 선분 당 최대 연결 선분의 수를 입력 인자로 설정한 실험 에서, 본 논문에서 제안된 방법은 최소 신장 트리를 이용한 방법과 비교하여 연결 생성 시간은 평균 192.0% 증가하였으나, 연결 길이는 평균 6.8%에 감소하였다. 이는 연결 방법을 찾는 시간보다는 연결 길이를 단축하는 것이 더 중요한 응용에 제안된 방법이 유용할 수 있음을 보인다.

• 한국발생생물학회지:발생과생식
• /
• 제16권3호
• /
• pp.205-217
• /
• 2012

The ovarian cycle, the biological minimum size, and artificial spawning frequency by artificial spawning induction of the female hard clam, Meretrix petechialis, were investigated by histological observations and morphometric data. The ovarian cycle of this species can be classified into five successive stages: early active stage, late active stage, ripe stage, partially spawned stage, and spent/inactive stage. The spawning period was from June to September, and the main spawning occurred between July and August when the seawater temperature exceeds over $20^{\circ}C$. The biological minimum size (shell length at 50% of first sexual maturity) in females were 40.39 mm in shell length (considered to be two years of age), and all clams over 50.1 mm in shell length sexually matured. In this study, the mean number of the spawned eggs by spawning induction increased with the increase of size (shell length) classes. In case of artificial spawning induction for the clams > 40.39 mm, the number of spawned eggs from the clams of a sized class was gradually decreased with the increase of the number of the spawning frequencies (the first, second, and third spawning). In the experiments of artificial spawning induction during the spawning season, the interval of each spawning of this species was estimated to be 15-18 days (approximately 17 days).

• 한국광학회지
• /
• 제15권4호
• /
• pp.293-298
• /
• 2004

Double-Sided Deep-Ridge(DSDR) 수직 방향성 결합기의 날개구조부 폭과 두께가 편광에 따른 결합길이에 미치는 영향에 관하여 연구하였다. 날개구조부가 존재하지 않는 DSDR 수직 방향성 결합기는 편광에 무관한 결합길이를 가질 수 없음을 볼 수 있었다. 일정한 날개구조부 두께에 대하여 날개구조부 폭이 특정 길이 이상이 되면 TE 모드와 TM 모드의 결합길이의 변화는 거의 없으며 또한 두 모드의 결합길이의 차이도 거의 발생하지 않음을 볼 수 있었다. 따라서 편광에 무관한 결합길이를 가지는 DSDR 수직 방향성 결합기를 구현하기 위한 최소 날개구조부 폭이 존재함을 볼 수 있었다. 이러한 최소 날개구조부 폭은-같은 코어 두께에 대해서는 날개구조부 두께가 증가할수록, 같은 날개구조부 두께에 대해서는 코어 두께가 감소할수록-증가함을 볼 수 있었다. 또한 최소 날개구조부 두께는 코어의 두께에 의하여 결정됨을 볼 수 있었고 코어의 두께가 증가할수록 최소 날개구조부 두께는 감소함을 볼 수 있었다.

• 대한조선학회논문집
• /
• 제52권3호
• /
• pp.236-247
• /
• 2015

In this paper, the experimental equipments for ventilated supercavitation in cavitation tunnel is constructed and the basic data of ventilated supercavitation regard to the entrainment coefficient and Froude number is fulfilled. The experiments are conducted for the disk cavitator with injecting air and the pressure inside cavity and the shape of cavity are measured. As the entrainment coefficient increases while the Froude number is kept constant, the ventilated cavitation number decreases to a minimum value which decreases no more even with increasing the air entrainment. The minimum value of ventilated cavitation number, caused by the blockage effect, decreases according to increasing the diameter ratio of test section to cavitator. The cavity length is rapidly enlarged near the minimum cavitation number. In low Froude numbers, the cavity tail is floating up due to buoyancy and the air inside the cavity is evacuated from its rear end with twin-vortex hollow tubes. However, in high Froude numbers, the buoyancy effect is almost negligible and there is no more twin-vortex tubes so that the cavity shape becomes close to axisymmetric. In order to measure the cavity length and width, the two methods, which are to be based on the cavity shapes and the maximum width of cavity, are applied. As the entrainment coefficient increases after the ventilated cavitation number gets down to the minimum cavitation number, the cavity length still increases gradually. These phenomenon can be confirmed by the measurement using the method based on the cavity shapes. On the other hand, when the method based on the maximum width of cavity is used, the length and width of the cavity agree well with a semi-empirical formular of natural cavity. So the method based on the maximum width of cavity can be a valid method for cavitator design.