• Journal of Biosystems Engineering
• /
• 제9권1호
• /
• pp.11-21
• /
• 1984

This study was intended to analyze the dynamic force system which induced the shattering of paddy grains. A model to predict the shattering of paddy grains was developed, and physical quantities, such as mass distribution and rigidity of rice plant, needed for evaluating the minimum shattering forces were also measured. Under the assumption that rice plant right before harvesting is a vibratory system, the mathematical model of the vibratory system was developed and solved with the varied conditions of forcing functions. The results of the study were summarized as follows: 1. The shattering of grain occurred at the abscission layer of grain by the bending moments resulted from the impact force due to the collision of panicles of rice plant. 2. The vibratory model developed for milyang 23 rice variety was analyzed to give the natural frequencies of 7-9 Hz, which were closely related with the excitation frequencies of 4-10 Hz caused by various machine parts besides engine. Thus, avoiding the resonance should be taken into consideration in the design of the harvesting machinery. 3. It was analyzed to predict the lowest frequency that could develop the shattering when the excitation force was applied to the lower end of stem. The lowest frequency for the Milyang 23 rice variety ranged from 8.33 Hz to 11.66 Hz as the amplitude varied from 1 cm to 2.5 cm. 4. The degree of shattering depended upon the magnitude of the impact force and its application point. For Milyang 23 rice variety, the minimum impact force developing the shattering was $5g_f$ when it was applied at 1 cm above the lower end of stern and $1g_f$ when applied at 5 cm above the lower end of stem. 5. The minimum colliding velocity of the panicle, when it was on the ground that would just develop the shattering, was given as follows, $$V=\sqrt{\frac{K_t}{m_g}{\cdot}{{\phi}^2}}$$ where V : The colliding velocity of the panicle against ground to cause the shatteering of rice grain. (cm/sec) $K_t$ : The minimum spring constant for bending at the abscission layer of grain. (dyne-cm/rad) ${\phi}$ : The minimum shattering angle of grain (rad) $m_g$ : The maximum mass of grain. (g).

• 대한교통학회지
• /
• 제22권7호
• /
• pp.147-154
• /
• 2004

COSMOS에서 포화도에 따른 현시 배분시 최소녹색시간에 의해 영향을 받는 경우 불균형적인 배분이 발생한다. 포화도에 따라 배리어를 나누게 되면 수요가 많은 광로측 배리어의 값이 더 많이 배분되고 상대적으로 소로측 배리어는 적게 배분된다. 배리어 배분 후 포화도에 따라 현시를 배분하면 최소녹색시간 확보로 인해 직진 이동류가 사용 가능한 녹색시간의 대부분을 쓰게 되므로 좌회전의 경우 녹색시간이 짧아져 통행권이 박탈당하는 문제가 발생한다. COSMOS에서는 이러한 문제점을 안고 있는 지역을 이중횡단보도를 설치하여 횡단보도 중간에 보행자용 교통섬을 설치하여 좌회전 현시와 이어지는 직진현시를 이용하여 횡단하도록 하였다. 본 연구에서는 이를 개선하기 위해 최소녹색시간을 고려하여 배리어를 계산하고 이동류별 포화도 비율에 따라 녹색시간을 계산한다. 개선 방안의 평가를 위해 아주대학교에서 개발한 COSMOS 평가 시뮬레이터를 이용하여 기존 알고리즘과 개선알고리즘으로 v/c비 $0.4{\sim}1.2$ 범위의 교통상황별로 지체시간을 비교하였다. 향후 개발된 알고리즘의 교통상황에 따른 적용시점에 관한 연구가 추가되어진다면 신호교차로의 운영효율을 극대화시킬 수 있을 것으로 기대된다.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2008년도 춘계학술발표대회 논문집
• /
• pp.203-208
• /
• 2008

The purpose of the study is to establish the concept of residential standard, and at the same time to investigate the area of the minimum residential standard in the countries of the world through the preceding studies. In addition, it also aims at establishing the objective residential standard by comparing the residential standard of Korea with that of foreign countries, examining the problems and finding out the matters to be improved through the comparison of the residential standard in advanced countries with the minimum residential standard of Korea. The standard residential area, derived from the process of examining the minimum residential standard, will be used as the basic material for the calculation of the reasonable area in the surface plan for the study of low-cost housing development. The method of the study is to establish the concept of residential standard and at the same time to find out the problems in the minimum residential standard of Korea and improvement methods through the comparison of the residential standards in other countries. As the result of the studies focused on the area among the residential standards, it is found out that the Korea's residential area per capita is established as the least in comparison with that of advanced countries. The real area decided depending on the size of social space suitable for living can play a role in improving the degree of satisfaction in the person's living in the residential area. Therefore, it is urgently necessary to make a depth study on the surface area of the minimum residential standard, and it is also required to propose the residential standard and directions for the improvement of the qualitative level rather the quantitative expansion of residential structures.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1394-1397
• /
• 1995

In the hazardous areas where explosive gases, vapor or mists exist, electrical apparatus and installations must be of explosion-proof construction to prevent or limit the danger of the ignition of potentially explosive atmosphere. In Korea, nine types of protection have been specified in the government regulations at present: flameproof enclosure, pressurization, oil immersion, increased safety, intrinsic safety, non-incendive, sand filling, encapsulation, and special types. Among these types, the intrinsic safety has the construction which limit or by-pass igniting the electric energy using electronic devices. This type has lots of merits but at the same time requires a high-degree of technology. In this paper, we investigated several dominating factors which affect the minimum ignition energy: this energy plays a very important role in design and evaluation of the intrinsic safety type electrical apparatus. Eletrode material, which is one of the most important factors, was intensively studied for the five sorts of material(Al, Cd, Mg, Sn, and Zn) with performing experiment in a low-voltage inductive circuit using IEC-type spark apparatus. The experimental results show that the minimum ignition energy of electrode material is varied: highest in Cd and lowest in Sn. We also confirmed the effect of eletrode make-and-break speed and magnetic field magnitude.

• Geomechanics and Engineering
• /
• 제7권5호
• /
• pp.525-537
• /
• 2014

The typical design of ground improvement with prefabricated vertical drains (PVD) and surcharge preloading involves a series of deterministic analyses using averaged or mean soil properties for the various combination of the PVD spacing and surcharge preloading height that would meet the criteria for minimum consolidation time and required degree of consolidation. The optimum design combination is then selected in which the total cost of ground improvement is a minimum. Considering the variability and uncertainties of the soil consolidation parameters, as well as considering the effects of soil disturbance (smear zone) and drain resistance in the analysis, this study presents a stochastic cost optimization of ground improvement with PVD and surcharge preloading. Direct Monte Carlo (MC) simulation and importance sampling (IS) technique is used in the stochastic analysis by limiting the sampled random soil parameters within the range from a minimum to maximum value while considering their statistical distribution. The method has been verified in a case study of PVD improved ground with preloading, in which average results of the stochastic analysis showed a good agreement with field monitoring data.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2008년도 한국우주과학회보 제17권2호
• /
• pp.23.4-23.4
• /
• 2008

In March and April 2001, the apogee (~9 Re) of the Polar spacecraft was located near the subsolar magnetopause with its orbital plane nearly parallel to a magnetic meridian plane. Polar electric and magnetic field data acquired during the two-month interval of solar maximum have been used to study fundamental standing Alfven waves near the subsolar meridian plane (magnetic local time = 1000-1400 hours) at magnetic latitudes from the equator to $\pm45$ degrees and at L values between 7 and 12. In the frequency band from 1.5 to 10 mHz, fundamental mode oscillations were identified based on high coherence (more than 0.7) and an approximately 90-degree phase shift between the azimuthal magnetic and radial electric field components. The L dependence of the fundamental frequencies is studied, and the frequencies are compared with those observed near the solar minimum interval (Takahashi et al. 2001). We found that the average frequencies in solar maximum are lower than those in solar minimum by a factor of ~2. This implies that the mass density in solar maximum is higher than that in solar minimum by a factor of ~4. Since there is a positive correlation between solar irradiance and solar activity, we suggest that the ionosphere in solar maximum produces more ions and load magnetic flux tubes with more ions.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.321-325
• /
• 2004

Linear motor feed drive systems have been broadly used in machine tools or precision automatic feed systems. Recently, modem machine tools require high speed and high precision feed drive system to achieve high productivity. Unfortunately, a feed drive system, even though it was optimum designed, may experience severe transient vibrations during high-speed operation if its feed rate control is unsuitable. A rough feed rate curve having discontinuity in its acceleration profile causes a serious vibration problem in the feed slides system. This paper presents a feed rate optimization of a machine tool feed slide system, which is driven by a linear motor, for its minimum vibrations. Firstly, a 4-degree-of-freedom lumped parameter model is proposed for the vibration analysis of a linear motor driven machine tool feed drive system. Next, a feed rate optimization of the feed slide is carried out for minimum vibrations. The feed rate curve optimization strategy is to find out the most appropriate acceleration profile with jerk continuity. Of course, the optimized feed rate should approximate to the desired one as possible. A genetic algorithm with variable penalty function was used in this feed rate optimization.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 추계학술대회논문집
• /
• pp.962-966
• /
• 2004

Ball screw feed drive systems have been broadly used in machine tools or precision automatic feed systems. Recently, modern machine tools require high speed and high precision and drive system to achieve high productivity. Unfortunately, a feed drive system, even though it was optimum designed, may experience severe transient vibrations during high-speed operation if its feed rate control is unsuitable. A rough feed rate curve having discontinuity in its acceleration profile causes a serious vibration problem in the feed slide system. This paper presents a feed rate optimization of a machine tool feed slide system, which is driven by a ball screw, for its minimum vibrations. Firstly, a 6-degree-of-freedom lumped parameter model was proposed for the vibration analysis of a ball screw driven machine tool feed drive system. Next, a feed rate optimization of the feed slide was carried out for minimum vibrations. The feed rate curve optimization strategy is to find out the most appropriate acceleration profile having finite jerk. Of course, the optimized feed rate should approximate to the desired one as possible. A genetic algorithm with variable penalty function was used in this feed rate optimization.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제15권3호
• /
• pp.1030-1050
• /
• 2021

The edges with "bridge characteristic" play the role of connecting the communication between regions in power optical cable network. To solve the problem of mining edges with "bridge characteristic" in provincial power optical cable network, the complex power optical cable network model is constructed. Firstly, to measure the generated potential energy of all nodes in n-level neighborhood local structure for one edge, the n-level neighborhood local structure topological potential is designed. And the minimum connected chain attenuation is designed to measure the attenuation degree caused by substituted edges. On the basis of that, the minimum connected chain attenuation topological potential based measurement is designed. By using the designed measurement, a bridge-edges mining algorithm is proposed to mine edges with "bridge characteristic". The experiments are conducted on the physical topology of the power optical cable network in Jilin Province. Compared with that of other three typical methods, the network efficiency and connectivity of the proposed method are decreased by 3.58% and 28.79% on average respectively. And the proposed method can not only mine optical cable connection with typical "bridge characteristic" but also can mine optical cables without obvious characteristics of city or voltage, but it have "bridge characteristic" in the topology structure.

• 한국식품과학회지
• /
• 제17권1호
• /
• pp.5-7
• /
• 1985

인산염이 쌀전분의 호화에 미치는 영향을 X-ray 회절법으로 조사하였다. 인산염은 멥쌀전분의 호화에 필요한 수분을 감소시켰다. 5% 멥쌀전분 현탁액의 호화온도는 인산염에 의하여 영향을 받지 않았으나, 같은 온도에서는 인산염의 존재시 호화도는 높은 값을 보였다. 인삼염은 찹쌀전분의 경우 호화에 영향을 미치지 않았다.