• 한국수소및신에너지학회논문집
• /
• 제17권4호
• /
• pp.418-424
• /
• 2006

In order to improve the activation properties of the $AB_2$ type hydrogen storage alloys for Ni-MH battery, the alloy surface was modified by employing high energy ball milling. The $Zr_{0.54}Ti_{0.45}V_{0.54}Ni_{0.87}Cr_{0.15}Co_{0.21}Mn_{0.24}$ alloy powder was ball milled for various period by using the high energy ball mill. As the ball milling time increased, activation of the $AB_2$ type composite powder electrodes were enhanced regardless of additives. When the ball milling time was small discharge capacities of the $AB_2$ type composite powder electrodes increased with the milling time. On the other hand for large milling time it decreased with increasing milling time. The maximum discharge capacity was obtained by ball milling for 3-4 min.

• Journal of Welding and Joining
• /
• 제20권1호
• /
• pp.47-54
• /
• 2002

Powder type Ag system insert metals were manufactured by ball milling process. The variables of milling process such as milling media, revolution speed and powder/ball weight ratio were constant except the milling time. The milling times were selected for 24, 48 and 72 hours. The insert metals made by milling process were evaluated by performing scanning electron microscope, x-ray and DSC(differential scanning calorimetry) analysis, and further in terms of wettability test. The selected insert metals that have the good characteristics compared to commercial insert metals were applied to make the brazed joints of the steel/steel and the steel/WC superhard particles. The characterizations of those brazed joints were also conducted by microstructural observations, shear tensile tests and microhardness measurements. The results indicated that milling time of 48 hours for making powder type insert metals was the best condition showing the small amount of oxides residue, low wetting angle and stable microstructure. The brazed joints that applied the 48 hours milled insert metal were very sound condition indicating the shear tensile value of $2.29{\times}102$ MPa and the microhardness of 138VHN. Further, the amount of the porosity was appeared to be lower than that of the commercial insert metals.

• Journal of Biosystems Engineering
• /
• 제7권2호
• /
• pp.72-85
• /
• 1983

Rice whitening is performed by basically two different whitening actions known as abrasive and frictional. The former adopted in the emery stone abrasive type whiteners and the latter in the jet-air friction type. Comparative milling yields and whitening efficiencies between the whitening system consisting of jet-air friction type whiteners only and the system consisting of both abrasive- and jet-air friction-types have not yet been rigorously defined. This study was to examine the effect of combined operations of abrasive- and jet-air friction-type rice whiteners on milling yields and whitening efficiencies. The small capacity commercial units of the abrasive- and friction-type whiteners were used for the experiments. The combinations of whitening treatments were: 1) Once in the abrasive type and then two to three times in the friction type, 2) twice in the abrasive and then two to three times in the friction type and 3) three to five times in friction type. In these tests, counter pressures for the friction type whiteners were established differently as required to get about the same degree of whitening at the end of predetermined numbers of the repeated operations. The speed of emery stone and the slot angle of the screen were also the factors varied in the abrasive type whitener. Sheukwang rice variety having 13.05% M.C. was used in the tests. The dependent variables were the milled- and head-rice recoveries and electricity consumption. The results of the study are summarized as follows: 1. It was found that in the whitening systems consisting of abrasive- and friction-type whiteners slot angle of the screen, the rotational speed of emery stone roller had significant effect on the milling yields and whitening efficiency. In general, the increase of the emery stone roller speed from 690 to 950 rpm presented a positive effect on milling yield, and one-pass abrasive milling combinations had higher milling yields than two-pass abrasive milling combinations. 2. It was apparent that if the slot angle of the screen and the speed of emery stone roller are modified and set at an optimum level, the combination whitening system consisting of abrasive- and friction-type whiteners is better than the pure frictional whitening system consisting of jet-air friction type in terms of milling yields and efficiencies. 3. In the rice whitening system consisting of abrasive- and jet-air friction-type whiteners, the best whitening performance was obtained when the slot angle of the screen and the rotational speed of emery stone roller were $45^{\circ}$ and 950rpm, respectively, for the one-pass abrasive milling combinations. However, for the two-pass abrasive mi11ing combinations, the best performance was obtained with $75^{\circ}$ of slot angle and 950 rpm of the emery stone roller speed. 4. As compared with pure frictional whitening systems, the combination systems produced more milled rice by 0.8-1.0% point and more head rice by 0.5-1.5% point, and consumed less electricity by 0.15-0.20 KwH per 100kg of milled rice when the abrasive whiteners were operated in the modified conditions as described in item 3 above. Further study is recommended to find out optimum operational and design conditions of abrasive type whiterners.

• Journal of Biosystems Engineering
• /
• 제8권1호
• /
• pp.17-29
• /
• 1983

The milling process is considered as causing one of the greatest grain losses among all the processes in rice post-production. Major source of grain losses in the rice milling is considered as the whitening process. This study was attempted to develop an abrasive-type whitener, the whitening chamber of which being supplied by jet-air evenly and continuously. To investigate the milling performance by the new whitener, three kind of emery-stone grit(#36, #41, and #46), and three levels of rotational speed of emery stone roller (950, 1070, and 1200 rpm) were tested. The jet-air abrasive-type whitener was also compared with the conventional abrasive-type having no jet-air blower in terms of their milling performance. In addition, the effect of different combinations of sequential uses of the abrasive- and friction-type whiteners on the milling performance was also experimentally evaluated. The results of this study are summarized as follows; 1. In general, the whitening system combined with the abrasive type whitener with jet-air supply, which was newly designed, and the existing jet-air friction type whiteners produces more milled- and head-rice by about 0.3% points and 2.8% points, respectively than the system combined with the existing abrasive type without the jet-air supply under the same operational conditions. The former also consumed less electricity by 0.024 KwH per 100kg of milled rice production and gave more milling capacity by about 35 kg/hr. As compared with the conventional whitening system consisting of jet-air friction type whiteners only, the former yielded more milled- and head-rice by 1.5% points and 4.4% points, respectively. 2. The abrasive roller having 46 grit emery was better than the roller having 36 grit in aspects of milling performance and machine efficiency, in general. 3. With regard to the effect of combination method of abrasive type and friction type whiteners, one pass in abrasive type plus three passes in friction type gave better milling performance and energy efficiency than the two passes in abrasive type plus two passes in friction type regardless of the designs of the emery stone rollers. 4. The increase in rotational speed of the emery stone roller from 950 rpm to 1200 rpm presented negative effects on milled and head-rice yields and machine efficiency, but slightly positive effect on milling capacity.

• Journal of Biosystems Engineering
• /
• 제4권2호
• /
• pp.1-8
• /
• 1979

This study was carried out to investigated the actual state of rice milling at local milling plants and to find out sources for elevating their milling recoveries in both quantity and quality. At 36 local milling plants located in Gyeongnam and Jeonnam , milling recoveries and head rice recoveries were measured with respect to their different milling systems and rice varieties. Then, the same samples of rice were milled by experimental milling equipments at laboratory, and the two experimental results were compared in order to determine the amount of milling recovery possibly to be increased. The results of this study are as follows ; 1. Milling recoveries of rice at local milling plants were proved to have no relationship with milling systems, and were 68.1% per ent and 72.6percent on an average with new variety and native variety, respectively. 2. The milling recoveries above stated can be elevated 4.5 percent and 2.9percent with new variety and native variety, respectively, by developing and extending technologies of manufacturing and handling rice milling machinery. 3. The head rice recovery of new variety at local milling plants has insignificant differences among milling systems, and was 54.8 percent on the average. With native variety, the recovery by friction type rice polisher was 0.9percent higher than that of friction-abrasive type polisher, and was 64.9 percent on the average. 4. The head rice recoveries of new variety and native can be elevated 5.1percent and 3.9percent, respectively, by the same stimulation above mentioned.

• Journal of Biosystems Engineering
• /
• 제14권1호
• /
• pp.41-48
• /
• 1989

In order to provide a basic information for the government policy in the future, rice milling costs of Small Capacity Farm-house Rice Whiteners (SCFRW) were estimated by surveying and analyzing the major factors to affect their costs. Two types of SCFRW having one stage and two stage milling process and two rice varieties, Tong-il and Akibare, were considered for their cost estimation, respectively. Also, their costs were compared with those of Private Custom-work Mill in order to determine its economical feasibility. The results were concluded as follows; 1. Major factors to affect the costs were annual milling quantity, purchase price of SCFRW and grain milling loss. 2. Total milling costs of SCFRW were a function of annual milling quantity. These costs decreased rapidly as annual milling quantity increased. 3. In comparison of milling costs between single pass type and double pass type SCFRW, the former was more economical than the latter. 4. Also, in comparison of milling costs between two varieties by using SCFRW, Akibare was less expensive than Tong-il. 5. In comparison with private Custom-work Mill, both single pass and double pass type SCFRW were less economical than private Custom-work Mill. 6. In order to have an economical feasibility, SCFRW should be designed and developed to reduce its milling loss and purchase price.

• 농업과학연구
• /
• 제44권3호
• /
• pp.416-423
• /
• 2017

This study aimed to identify milling characteristics depending on the rotating speed of the main shaft of the cutting-type rice milling machine which can minimize the conventional milling process. Brown rice, which was produced in Gunsan-si, Jeollabuk-do, Republic of Korea, in 2016, was used as the experimental material. The milling characteristics of white rice were measured under four different rotating speeds of main shaft: 950 - 1,050 rpm, 1,000 - 1,100 rpm, 1,050 - 1,150 rpm, and 1,100 - 1,160 rpm. For each shaft speed, 300 kg of brown rice was processed, and the milling characteristics were measured according to the whiteness, grain temperature, cracked rice ratio, broken rice ratio, turbidity, and energy consumption. The whiteness of rice grain was found to be consistent at around $40{\pm}0.5$ only when milled at the shaft speed of 950 - 1,050 or 1,000 - 1,100 rpm. The grain temperature during the milling process increased by 11.35 to $11.85^{\circ}C$, showing little differences amongst shaft speeds. The cracked rice ratio increased by 8.2 to 10.4% at all conditions. The broken rice ratio ranged from 0.58 to 0.76%, reflecting a low level. The turbidity after milling was 54.8 ppm when milled at 1,000 - 1,100 rpm. Energy consumption of 12.98 and 12.18 kWh/ton were recorded at the shaft speed of 1,000 - 1,100 and 1,050 - 1,150 rpm, respectively. The result of this study indicates that the optimal rotating speed of main shaft would be 1,000 - 1,100 rpm for a cutting-type rice milling machine.

• 한국세라믹학회지
• /
• 제31권3호
• /
• pp.337-345
• /
• 1994

The reaction-sintered alumina and zirconia-alumina ceramics having low firing shrinkage were prepared from the Al/Al2O3 or Al/ZrO2(Ca-PSZ) powder mixtures via the attrition milling. And in this milling process the effect of the characteristics of used powders was investigated. Attrition milling was much more effective in reducing the particle size of ceramic/metal mixed powders than ball milling. Powder mixtures of flake-type Al with coarse alumina was much more effectively comminuted by the attrition milling than the mixtures of globular-type Al with coarse alumina powders. And coarse alumina than fine alumina was much more beneficial in cutting and reducing the ductile Al particles. In the contrary to Al/Al2O3 powder mixtures, Al/ZrO2 powder mixtures was not effectively comminutd. But whether using the alumina ball media or attrition milled with Al2O3 powder rather than Al, the milling efficiency was much more increased.

• 한국식품과학회지
• /
• 제22권2호
• /
• pp.199-205
• /
• 1990

우리나라 쌀의 품종별 도정 및 품위특성을 조사하여 합리적인 시장성을 평가할 수 있는 방법을 모색하고자 일반계 쌀과 다수계 쌀의 품종별로 품위 및 도정특성을 조사 분석한 결과는 다음과 같다. 유형별 도정률은 일반계가 높고 쇄미율은 통일계가 높았으나 미강률은 큰 차이가 없었으며 벼에서 쌀까지의 도정률은 현미의 용적중, 제현율 및 현백률이 높은 품종이 요구되고 현미의 쇄립률, 심복백립률, 왕겨율, 쇄미율 및 미강률이 낮은 품종은 쌀의 품위 및 수율이 향상되었다.

• 한국염색가공학회지
• /
• 제34권3호
• /
• pp.135-145
• /
• 2022

In this study, the dyeability of 0.06-denier-per-filament (dpf) ultrafine sea-island-type nylon knitted fabric was investigated and compared with that of 1.0-dpf general nylon with respect to four types of dyes. In particular, leveling, milling, half-milling, and metal-complex dyes were compared at concentrations of 0.5%, 1.0%, 2.0%, 4.0%, and 8.0% on-weight-fabric (o.w.f). In each case, staining was performed at 100 ℃. The dyeabilities of the materials were compared in terms of the depth of color as defined by the ratio of the absorption coefficient (K) to the scattering coefficient (S). Results indicated generally low K/S values for both the 0.06-dpf ultrafine sea-island-type nylon and 1.0-dpf general nylon. In terms of the dye type, the milling and half-milling dyes exhibited K/S values of ≥20 for all colors of yellow, red, and blue for the 0.06-dpf ultrafine yarn sea-island-type nylon, which were superior to those of the other dye types. Hence, the milling and half-milling dyes are considered more suitable than the other dyes. Further, a comparison of dye fastness and compatibility revealed that the half-milling dye was the most suitable dye for the 0.06-dpf ultrafine sea-island-type nylon.