• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.87-90
• /
• 2002

For the broad band wireless communications system, the composition of the millimeter wave system is needed. In other to commercialize that system, satisfaction of high frequency characteristic and low cost process is required. In this study, BPF which is very sensitive to the characteristic of fine line designed and fabricated using photoimageable thick film technology.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.4
• /
• pp.53-58
• /
• 2016

A ray tracing method to analyze the propagation channel characteristics for a millimeter-wave indoor wireless communication system is presented. Reflected rays from planar as well as rough surfaces are included. Transmitted rays though a thin dielectric slab are considered. Maps representing received power levels and RMS delay spread from a transmitter in a rectangular room are shown. The received power levels in the empty room for bottom's roughness factors of 0 and 0.13 are represented. The simulation results are well consistent with the calculation of Friis equation with reflection coefficient. Any size of furniture the shape of plane form can be positioned anywhere in the room.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.3
• /
• pp.71-74
• /
• 2012

We have manufactured a close range Dicke type radiometer which consists of two stage low noise amplifier and diode detector. Frequency range of this system is 35 GHz. And this is used for studying temperature calibration on specific objects. We have present millimeter-wave radiometer's thermal calibration method and its characteristics. From absolute temperature 299K to 309K, in proportion to increase temperature, output voltages are linearly increased. In this case, undefined objects can be measured thermal noise temperature relatively. Overall from absolute temperature 214K to 309K, we have obtained relation of temperature and output voltage;V= 0.03601K - 10.70517.

• Journal of Satellite, Information and Communications
• /
• v.12 no.2
• /
• pp.61-64
• /
• 2017

A phase shifter is one of the key components that change the phase of an individual antenna in millimeter-wave phased array system. This paper presents a low-loss phase shifter design with two parallel 2-state amplifiers. To get the same gain of $0^{\circ}/180^{\circ}$ each state, delay lines are in the middle of each stage of the 2-Stage amplifiers. Normally, when adding AMPs in parallel, a power combiner/divider such as Wilkinson Power Combiner/Divider is added, but they are directly connected because it can cause added losses in silicon wafer. The measured data shows 12dB gain and 174-degree phase difference at 5GHz.

• Journal of the Institute of Convergence Signal Processing
• /
• v.18 no.1
• /
• pp.21-24
• /
• 2017

Passive millimeter wave (MMW) imaging penetrates clothing to detect concealed objects. The distances extraction to the concealed objects is critical for the security and defense. In this paper, we address a passive stereo 3 mm MMW imaging system to extract the longitudinal distance to the concealed object. The concealed object area is segmented and extracted by the k-means clustering algorithm with splitting initialization. The distance to the concealed object is estimated by the corresponding centers of the segmented objects. In the experimental two pairs (each pair for horizontal and vertical polarization) of stereo MMW images are obtained to estimate distances to concealed objects.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.9
• /
• pp.25-33
• /
• 2007

In this paper, the high isolation and wideband 94 GHz MIMIC(Millimeter-wave Monolithic Integrated Circuit) single balanced cascode mixer was designed and fabricated. Also, we designed and fabricated a 3 dB tandem coupler which has a high isolation and wideband characteristic. The single balanced resistive mixer which does not require an external IF balun was designed using the 0.1 ${\mu}m$ InGaAs/InAlAs/GaAs metamorphic HEMT(High Electron Mobility Transistor). The DC characteristics of MHEMT's are 665 mA/mm of drain current density, 691 mS/mm of maximum transconductance. The current gain cut-off frequency($f_T$) is 189 GHz and the maximum oscillation frequency($f_{max}$) is 334 GHz. A 94 GHz single balanced cascode mixer was fabricated using our 0.1 ${\mu}m$ MHEMT MIMIC process. From the measurements, the fabricated couplers showed wideband characteristics. The conversion loss of single balanced cascode mixer was 9.8 dB at an LO power of 10.9 dBm. The LO to RF isolation of single balanced cascode mixer was 29.5 dB at 94 GHz. We obtained in this study a higher LO-RF isolation compared to some other single balanced mixers.

• ETRI Journal
• /
• v.39 no.2
• /
• pp.255-263
• /
• 2017

This paper proposes a graph-theatrical approach to optimize spatial reuse by adopting a technique that quantizes the channel information into single bit sub-messages. First, we introduce an interference graph to model the network topology. Based on the interference graph, the computational requirements of the algorithm that computes the optimal spatial reuse factor of each user are reduced to quasilinear time complexity, ideal for practical implementation. We perform a resource allocation procedure that can maximize the efficiency of spatial reuse. The proposed spatial reuse scheme provides advantages in beamforming systems, where in the interference with neighbor nodes can be mitigated by using directional beams. Based on results of system level measurements performed to illustrate the physical interference from practical millimeter wave wireless links, we conclude that the potential of the proposed algorithm is both feasible and promising.

• ETRI Journal
• /
• v.38 no.1
• /
• pp.81-89
• /
• 2016

In this paper, a beam ID preamble (BIDP) technique, where a beam ID is transmitted in the physical layer, is proposed for efficient beam training in millimeter-wave cellular communication systems. To facilitate beam ID detection in a multicell environment with multiple beams, a BIDP is designed such that a beam ID is mapped onto a Zadoff-Chu sequence in association with its cell ID. By analyzing the correlation property of the BIDP, it is shown that multiple beams can be transmitted simultaneously with the proposed technique with minimal interbeam interference in a multicell environment, where beams have different time delays due to propagation delay or multipath channel delay. Through simulation with a spatial channel model, it is shown that the best beam pairs can be found with a significantly reduced processing time of beam training in the proposed technique.

• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.161-165
• /
• 2003

Optical 60 ㎓ millimeter-wave (MMW) signal generation is demonstrated using the sideband injection-locking method in the master/slave configuration, where two slave lasers are locked to two among several side-bands produced by the direct rf-modulation of a master laser. These two locked slave laser outputs beat against each other in the photo-detector and produce stable and very pure 60 ㎓ signals.

• Journal of electromagnetic engineering and science
• /
• v.5 no.4
• /
• pp.189-192
• /
• 2005

The measurement of unique rainfall phenomenon and rain attenuation on 38 GHz terrestrial links at South Korea in 1998 is presented. It was one of the most severe rainfall years at the measured region due to increased EI Nino signal. The rainfall rate exceeded at $0.01\%$ was 97.4 mm/h during a worst month and annual rate was 63.5 mm/h. Experimentally measured results have been compared with some models and found that the rain attenuation by system level was underestimated by the existing prediction models. As it was measured only three months, further study and measurement of rainfall and rain attenuation in this region are needed for stable millimeter-wave system operation at all times.