• Journal of the Korean Institute of Telematics and Electronics
• /
• v.19 no.5
• /
• pp.20-25
• /
• 1982

A realization method of the microwave oscillator is proposed by the inherently stable transistor with a cavily resonator feedback loop. The real Part of the output impedance of the inherently stable bipolar transistor can be made to be negative at the resonance frequency by the high-Q cavity feedback loop, and the oscillation condition can be obtained with the matching section of the load. In this work the microwave transistor oscillator is realized with a silicon bipolar transistor HXTR 2101 and a reentrani cavity, and characteristic of the output power 10m Watts at 2.33 GHz osc. frequency can be verified experimentally.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.3B no.1
• /
• pp.16-22
• /
• 2003

This paper presents an application of an impedance boundary condition to 3D vector finite element analysis of a multi-port cylidrical microwave cavity using Snell's law. Computing memory benefits and computing time reduction are obtained from this method compared with the conventional finite element method(FEM). To verify the method, a high permittivity scatterer in free space is analyzed and compared with the results of conventional (FEM). In addition, this method has been analyzed several types of cavities, including water load, to demonstrate the validity and accuracy of the program.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.4
• /
• pp.11-19
• /
• 1993

The complex permittivity and the linewidth of microwave ferrites are measured using the well known cavity perturbation method. The cavity perturbation method has been widely used for the measurement of complex permittivity and conductivity of low loss magnetic and dielectric materials at microwave frequencies. TT1-2000, TT73-2200, and G-113 samples ordered from Trans-Tech Inc, are tested. TE$_{103}$ and TE$_{106}$ rectangular waveguide cavities are fabricated and the ferrite sample of cylidrical rod and sphere shapes are prepared. The error between the measurement values and the supplier's data is less than 1 percent in case of $\varepsilon$’ and about 10 percent in case of linewidth ($\Delta$H). Worst case error analysis shows that our measured results are well within the error bound calculated from the accuracy specification of the measuring instruments.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.341-342
• /
• 2008

A conductivity of soot at microwave frequency is presented using a novel technique for complex permittivity of materials. The method overcomes limitations of conventional methods which are cavity perturbation and transmission/reflection method. Resonant frequencies and Q factors are measured and simulated for the cylindrical cavity, and they are compared to each other. Similar material property of both real material and simulation material produce similar values of resonant frequency and Q factor. The complex permittivity of material can be determined by simulating the cavity to change material property until the simulation results are nearly the same as the measurement results. Cylindrical cavity has been realized for measurement at 880 MHz, and conductivity of soot is measured. A sample was made by depositing the soot on the glass. The proposed method shows that the conductivity of soot is 11 S/m.

• Journal of the Korean Ceramic Society
• /
• v.29 no.4
• /
• pp.305-311
• /
• 1992

As compared with conventional sintering, rapid heating in microwave system could enhance sinterability and final properties of alumina with a very short sintering time. In this study microwave sintering was performed using zirconia brick as a reaction chamber which was positioned in a 2.45 GHz(700 W) multimode microwave cavity. Microwave-sintered alumina showed high density and smaller grain size than conventionally sintered alumina because the ratio of densification rate/grain growth rate was increased by rapid heating.

• Korean Journal of Materials Research
• /
• v.11 no.2
• /
• pp.146-150
• /
• 2001

Electromagnetic simulation was compared to the measurement with a network analyzer in the cavity resonator method which has been used for determining microwave quality factor. Scattering matrix $S_{12}$ obtained from the network analyzer was compared to the $S_{12}$ obtained from the simulation. The effects of the pore and the secondary phase of the dielectric resonator on the microwave quality factor were studied. From the simulated results, the dominant resonant $TE_{01\delta}$ mode was determined and the quality factor was observed to decrease with the pore and the secondary phase in the dielectrics.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.05a
• /
• pp.105-108
• /
• 2000

The fundamental characteristics of the cavity-backed slot antenna at 2.45 GHz are analyzed with the method of moment for the use of a part of rectenna element. The proposed antenna has a rectangular-narrow slot on the upper surface and a feed post and a parasitic post inside of the cavity. The interior posts are perpendicular to the slot surface in order that the microwave circuits can be attached to the bottom of the cavity. Theoretical results shows that the maximum return loss of 50 dB at the input terminal of the antenna is achieved.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.12
• /
• pp.1582-1585
• /
• 1988

A cavity perturbation technique is employed to determine the dielectric property of thin samples. Substrates in microwave integrated circuits are fabricated in sheet form and are expected to have a dielectric constant less than 10 and a dielectric loss better than 10**-3. This research aimed to determine both dielectric constant and dielectric loss with good accuracy. The tecynique makes use of thin circular disk samples placed in a right circular cylindrical cavity. The accuracy of measurements is within \ulcorner% for dielectric constnat and 3x10**-4 for dielectric loss.

• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.300-303
• /
• 1987

A microwave plasma generating system has been designed to study the properties of plasma. A microwave(2.45GHz) generated by the magnetron is transmitted to the cylindrical cavity through the the rectangular wave guide to generate hydrogen plasma. The electron temperature and the plasma density are measured by the Double Langmuir probe. A dilectric such as alumina is heated by the microwave add plasma. The surface temperature varies with the neutral gas pressure.

• Journal of the Korean Chemical Society
• /
• v.40 no.4
• /
• pp.235-242
• /
• 1996

A surfatron-type microwave induced plasma (MIP) cavity has been constructed, which can be easily interfaced with a gas chromatograph. Various plasma gases such as He, Ar and N2 were used to generate the MIP and small amounts of CO2 gases were injected through the MIP to obtain characteristic spectrum of each plasma gas and to study feasibility of the MIP as a soft ionization source. Since He and Ar plasmas have high metastable state energy, it was not possible to detect sample gas in molecular state. With N2 plasma, however, a strong emission of molecular ions could be detected owing to its low metastable state energy.