• 비파괴검사학회지
• /
• 제18권4호
• /
• pp.292-303
• /
• 1998

최근 자기적 특성의 변화가 재료의 미세조직적 상태에 민감하다는 보고가 있다. 재료의 미세조직은 상(phase), 결정립의 크기, 석출물 등의 타양한 인자로 구성되며, 본 연구에서는 이러한 인자들을 이용하여 재료의 특성과 Barkhausen noise(BN) 의 관계를 연관시키기 위 한 시도를 하였다. ASTM A 508 Gr. 3 원자로압력용기강을 대상으로 용접열영향부의 미세조직적인 변화를 일곱가지 대표적인 영역으로 구분하였고, 각 영역에서의 미세조직과 기계적특성의 변화를 파악한 후, 자 조건별로 BN을 측정하였다. 통상의 보자력이나 잔류자화 같은 자기적성질은 큰 변화가 없었지만, BN은 미세조직의 상태에 따라 현격한 변화를 보였다. 결정립과 석출물의 크기가 증가함에 따라 BN은 증가하였고. tempered martensite 보다는 tempered bainite 조직에서 높은 BN을 나타냈다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.114-123
• /
• 1995

Hot workability and microstructural development of 7075Al alloy were studied by hot torsion test. With decling temperature from 440$^{\circ}C$ to 340$^{\circ}C$, and strain rate ranges form 5 ${\times}$10-3/sec to 5 ${\times}$10-1/sec , flow stress and microstructural development were analyzed . The hot resoration mechanism was found to be dynamic recrystalization (DRX) form the analysis of the flow curves and the microstructures. In multistage deformation with decreasing temperature grain refinement was obtained effectively compared to conventional thermomechanical treatment (TMT) process. The strain of the 1st stage deformation at 440$^{\circ}C$ was found to play an important role for the next stage deformation behavior at 380$^{\circ}C$.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.397-402
• /
• 2001

Microstructural characteristics such as hydrates and porosity greatly influence the development of concrete strength. In this study, a strength estimation model for early-age concrete considerig, the microstructural characteristics was proposed, which considers the effects of both an increment of degree of hydration and capillary porosity on a strength increment. Hydration modeling and compressive strength test with curing temperature and curing ages were carried out. By comparing test results with estimated strength, it is found that the strength estimation model can estimate compressive strength of early-age concrete with curing ages and curing temperature within a margin of error.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.715-720
• /
• 2002

Silicon nitride samples with aligned whisker seeds were prepared with different amounts of yttria and alumina as the sintering additives. Their sintering behaviors and the microstructural developments between 2123K and 2323K were examined. The sample with larger amount of the sintering additives showed faster densification and grain growth. Even though addition of the aligned whisker seeds slightly retarded densification of silicon nitride, it improved the flexural strength and the fracture toughness. Both the flexural strength and the fracture toughness of silicon nitride with the aligned whisker seeds were increased as the amount of the sintering additives was increased.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.136-142
• /
• 2001

Recently, a much amount of attention has been paid not only to produce products with precise dimensional accuracy, but also to predict and control the microstructural evolution and mechanical properties of parts. Especially, to do the latter through computer simulation, the history of states factors influencing on these evolution such as temperature, strain, strain rate etc., should be calculated and a appropriate mathematical models for the prediction of microstructural evolution must be developed. Thus, in this study thermo-viscoplastic finite element program including the model for predicting microstructural has been developed. Also for the verification of developed program warm forging process for the rotor pole was simulated and the comparison between the results calculated and ones in the literature was made.

• 한국결정학회지
• /
• 제11권4호
• /
• pp.195-199
• /
• 2000

Ceramics based on CaTiO₃-NdAlO₃ solid solutions were synthesized in order to study their dielectric microwave properties. Microstructural analysis was performed with scanning electron microscopy (SEM) and transmission electron microscopy (TEM) using different analytical methods such as energy-dispersive X-ray spectroscopy (EDXS). It was observed that the heating conditions during sintering and cooling strongly affect the microstructural development of CaTiO₃-NdAlO₃-based ceramics. Various types and concentrations of structural defects were identified, for example, dislocations, twins and/or antiphase boundaries. all such defects resulted in a degradation of the dielectric microwave properties, in particular the quality factor Q. Dielectric properties of CaTiO₃-NdAlO₃-based ceramics can be improved by an appropriate thermal treatment of ceramics which results in a decrease in the concentrations of the identified microstructural defects.

• 한국정밀공학회지
• /
• 제15권7호
• /
• pp.129-138
• /
• 1998

The objective of this study is to demonstrate the ability of a computer simulation of microstructural evolution in hot forging of C-Mn steels. The development of microstructure is strongly dependent on process variables and metallurgical factors that affect time history of thermodynamical variables such as temperature, strain. and strain rate during deformation. Then finite element method is applied for the prediction of microstructural evolution, and it should be coupled with heat transfer analysis to consider the change of thermodynamical properties during forming process. In this study, Yada's recrystallization model and rigid-thermoviscoplastic finite element method are employed in order to analyze microstructural evolution during hot forging process. To show the validity and effectiveness of the proposed method, experiments are accomplished and the results of experiments are compared with those of simulations.

• 한국분말재료학회지
• /
• 제28권2호
• /
• pp.103-109
• /
• 2021

High-entropy alloys have excellent mechanical properties under extreme environments, rendering them promising candidates for next-generation structural materials. It is desirable to develop non-equiatomic high-entropy alloys that do not require many expensive or heavy elements, contrary to the requirements of typical high-entropy alloys. In this study, a non-equiatomic high-entropy alloy powder Fe_49.5Mn₃₀Co₁₀Cr₁₀C_0.5 (at.%) is prepared by high energy ball milling and fabricated by spark plasma sintering. By combining different ball milling times and ball-to-powder ratios, we attempt to find a proper mechanical alloying condition to achieve improved mechanical properties. The milled powder and sintered specimens are examined using X-ray diffraction to investigate the progress of mechanical alloying and microstructural changes. A miniature tensile specimen after sintering is used to investigate the mechanical properties. Furthermore, quantitative analysis of the microstructure is performed using electron backscatter diffraction.

• 한국해양공학회지
• /
• 제23권5호
• /
• pp.32-38
• /
• 2009

Silicon nitride samples with aligned whisker seeds were prepared with different amounts of yttria and alumina as the sintering additives. Their sintering behaviors and the microstructural developments between $1850^{\circ}C$ and $2050^{\circ}C$ were examined. The sample with larger amount of the sintering additives showed faster densification and grain growth. Even though addition of the aligned whisker seeds slightly retarded densification of silicon nitride, it improved the flexural strength and the fracture toughness. Both the flexural strength and the fracture toughness of silicon nitride with the aligned whisker seeds were increased as the amount of the sintering additives was increased.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 춘계학술강연 및 발표대회강연 및 발표논문 초록집
• /
• pp.7-7
• /
• 2006