• Journal of the Korean Physical Society
• /
• 제73권10호
• /
• pp.1506-1511
• /
• 2018

Spectral behaviors of lasing from semiconductor square ring microcavities with structures for unidirectional laser oscillation were investigated. When a tapered structure was introduced, the lasing envelope shifted to a shorter wavelength region. Statistical estimate of the additional loss caused by the tapered structure was carried out by analyzing spectral data from many sets of cavities with various sizes. When a saw-edged structure was introduced, the unidirectional lasing functioned well but no apparent spectral shift was observed due to negligible additional loss.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 창립 20주년기념 특별학술발표회
• /
• pp.60-61
• /
• 2009

• 한국광학회:학술대회논문집
• /
• 한국광학회 2009년도 창립 20주년기념 특별학술발표회
• /
• pp.384-385
• /
• 2009

• 한국광학회:학술대회논문집
• /
• 한국광학회 2006년도 하계학술발표회 논문집
• /
• pp.531-532
• /
• 2006

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
• /
• pp.297.2-297.2
• /
• 2014

Strong exciton-photon coupling in microcavities have generated an intense research effort since quasiparticles called exciton polaritons are produced and shows interesting phenomena. Most of studies have been done with GaAs based microcavities at cryogenic temperature. Recently, GaN material which has large exciton binding energy and oscillator strength has much attention because strong coupling between photon and exciton could be realized at room temperature. However, fabrication of high quality microcavity using GaN is challengeable due to the large mismatch between the lattice and the thermal expansion coefficient in GaN based distributed Bragg mirror. Here, we observed strong coupling regime of exciton-photon in GaN micro-rods which were grown by metalorganic vapour phase epitaxy (MOCVD) on Si substrate. Owing to the hexagonal cross-section of micro-rod, whispering gallery modes of photon are naturally formed and could be coupled with exciton in GaN. Using angle-resolved micro-photoluminescence measurement, exciton polariton dispersion curves were directly observed from GaN micro-rod. We expect room temperature exciton polariton condensation could be realized in high quality GaN micro-rod.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2005년도 제16회 정기총회 및 동계학술발표회
• /
• pp.90-91
• /
• 2005

• Journal of the Optical Society of Korea
• /
• 제16권2호
• /
• pp.162-165
• /
• 2012

Bow-tie modes were proposed in a grooved rectangular resonator and their lasing characteristics were investigated in semiconductor microcavities. The observed spacing between two adjacent lasing peaks from the grooved cavity was reduced compared to that of 4-bounce whispering gallery modes (WGMs) from the same-sized simple rectangular cavity due to increased round-trip path length of the bow-tie modes. The lasing spectra of bow-tie modes obtained from two adjacent corners showed highly correlated patterns while those of 4-bounce WGMs did not.

• 지질공학
• /
• 제32권3호
• /
• pp.339-350
• /
• 2022

경주시 골굴사 신생대 응회암에서는 다양한 형태의 타포니가 다수 발달한다. 응회암은 풍화변질되어 있는데, 석영, 장석류, 운모, 버미큘라이트, 녹니석, 스멕타이트와 제올라이트 광물인 아날사이트 등으로 구성된다. 타포니는 초기 단계에서는 각력이 제거된 동공이나, 응회암 결정 입자의 풍화변질에 의해 형성된 미세 동공에서부터 시작하여 점차 확대된다. 타포니는 사면의 반대방향으로 약하게 경사지면서 발달한다. 타포니의 상관계수는 폭-높이 0.839, 폭-깊이 0.900, 높이-깊이 0.856인데 서로 밀접한 관련성이 있다. 타포니 벽체가 제거되면 반달형이나 신장된 타포니로 되는데, 작은 동공들이 횡적으로 병합되면서 확대된다. 커다란 타포니 동공들은 암반 사면에 비하여 내부가 비어있기 때문에 암반의 강도가 더 낮다. 따라서 타포니 사면의 강도, 동공의 비율, 체적, 합병 양상에 대한 지속적인 모니터링이 요구된다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.371-376
• /
• 2003

The hot embossing process has been mentioned as one of major nanoreplication techniques. This is due to its simple process, low cost, high replication fidelity and relatively high throughput. As the initial step of quantitating the embossing process, simple parametric study about embossing time have been carried out using high-resolution masters which patterned by the DRIE process and laser machining. Under the various embossing time, the viscous flow of thin PMMA films into microcavities during Compression force has been investigated. Also, a study about simulating the viscous flow during embossing process has planned and continuum scale FDM analysis was applied on this simulation. With currently available test data and condition, simple FDM analysis using FLOW3D was made attempt to match simulation and experiment.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1036-1042
• /
• 2003

The hot embossing process has been mentioned as one of major nanoreplication techniques. This is due to its simple process, low cost, high replication fidelity and relatively high throughput. As the initial step of quantitating the embossing process , simple parametric study about embossing time have been carried out using high-resolution masters which patterned by the DRIE process and laser machining. Under the various embossing time, the viscous flow of thin PMMA films into microcavities during compression force has been investigated. Also, a study about simulating the viscous flow during embossing process has planned and continuum scale FDM analysis was applied on this simulation. With currently available test data and condition, simple FDM analysis using FLOW3D was made attempt to match simulation and experiment.