금속복합재료 개발을 위한 고온가압 성형공정은 기지재료의 비탄성거동과 성형체 내부의 기공에 대한 충진 과정을 수반하며 이러한 강화공정은 압력, 온도 그리고 강화재와 모재의 상대부피분률과 같은 공정변수의 영향을 받게 된다. 특히 티타늄금속기 복합재료의 강화공정은 강화재와 모재 사이의 기계적 혹은 열적 특성 차이 및 생산환경으로 인한 다양한 형태의 손상이 발생할 수 있으며 따라서 이들을 극복하기 위한 재료특성, 작용압력, 온도, 시간조건 등과 공정에 따른 조직의 진전 등 미소역학적 연구가 수반된 최적의 고온가압강화공정의 개발이 요구되어진다. 이를 위하여 본 연구는 VHP방식을 이용한 SiC/Ti-6Al-4V 연속섬유강화 금속기 복합재료의 강화공정실험을 수행하였으며 특히 미시역학적 접근에 따른 다공성 재료의 구성방정식을 이용하여 보강재와 기지재료의 변형거동과 고온가압공정에 필요한 다양한 조건들을 실험결과와 비교 연구하였으며 유한요소해석을 통해 공정변수와 그에 따른 결과들을 고찰하였다.
The purpose of this study was to compare the comfort sensation depending on four different kinds of denim blue jeans: cotton, cotton/tencel, tencel, cotton/pp. The objective and subjective experiments were conducted to measure the comfort of blue jeans. To investigate the objective comfort, physical properties related to thermal insulation, moisture properties and hand were measured. For subjective comfort measurement, 5 healthy female college students were taken as subjects. The outcomes of the experiments are as follows: The higher the air permeability and bulk density of the denim, the lower the thermal insulation, the thicker the denim, the higher the thermal insulation. Tencel blending denim showed the higher bulk density, the lower air contents, and consequently the lower thermal insulation than the other denims. Tencel showed the highest moisture regain, and cotton/tencel blend showed the highest water vapor permeability. Tencel denim had relatively better flexibility, shape stability and elastic recovery than the other denims. The total hand values of the denims by KES-FB system were not significantly different. Cotton and cotton/pp denims raised the subjects body temperature after excercise more than tencel or cotton/tencel denims. Average skin temperature was found to have a correlation with micro climate temperature and micro climate humidity. The correlation coefficients were 0.749 and 0.767, respectively. However, average skin temperatures were not significantly different among the materials. Pulse rate was found to be the highest when wearing cotton/pp and the lowest in case of cotton/tencel denim. The energy was consumed in order of cotton>cotton/pp>tencel>cotton/tencel. There was no significant difference in preference before excercise, but, after the excercise, the order of preference changed as the following; cotton/tencel>tencel>cotton/pp>cotton.
SiC materials have been extensively studied for high temperature components in advanced energy system and advanced gas turbine. However, the brittle characteristics of SiC such as low fracture toughness and low strain-to fracture still impose a severe limitation on practical applications of SiC materials. For these reasons, $SiC_f/SiC$ composites can be considered as a promising for various structural materials, because of their good fracture toughness compared with monolithic SiC ceramics. But, high temperature and pressure lead to the degradation of the reinforcing fiber during the hot pressing. Therefore, reduction of sintering temperature and pressure is key requirements for the fabrication of $SiC_f/SiC$ composites by hot pressing method. In the present work, Monolithic LPS-SiC was fabricated by hot pressing method in Ar atmosphere at 1760 $^{\circ}C$, 1780 $^{\circ}C$, 1800 $^{\circ}C$ and 1820 $^{\circ}C$ under 20 MPa using $Al_2O_3-Y_2O_3$ system as sintering additives in order to low sintering temperature. The starting powder was high purity ${\beta}-SiC$ nano-powder with an average particle size of 30 nm. Monolithic LPS-SiC was evaluated in terms of sintering density, micro-structure, flexural strength, elastic modulus and so on. Sintered density, flexural strength and elastic modulus of fabricated LPS-SiC increased with increasing the sintering temperature. In the micro-structure of this specimen, it was found that grain of sintered body was grown from 30 nm to 200 nm.
본 논문에서는 광전송시스템에서 파장분할다중화 광소자로 사용되는 박막필터형 광소자의 특성 분석 및 평가를 위해 입력광원을 모델링 하였으며 광경로에 대해 광선추적법을 사용하여 전산모의 한 광특성을 실험과 비교, 분석하였다. 그 결과 입력광원에 대한 cell 방식의 모델링이 결합효율의 정확도 및 가우시안 강도분포에 접근성을 볼 때 마이크로 옵틱스형 광소자 분석함에 있어 적합함을 알 수 있다. 박막필터형 광소자에 대한 최적 전산모의 결과 광섬유와 GRIN 렌즈 사이 거리가 0.24mm이며 GRIN 렌즈와 박막필터 사이 거리가 0.25mm일 때 최대 결합효율은 -0.11 ㏈이었으며 동일한 조건에의 실험결과 -0.35 ㏈의 최대 결합효율을 얻었다. 이것은 단심 및 이심페룰, GRIN 렌즈 등과 같은 구성품의 불완전성과 박막필터에 의한 손실을 고려할 때, 전산모의 결과와 매우 일치하는 것으로서 본 연구에서 제안한 입력광원의 모델링을 적용한 전산모의가 박막필터형 광소자의 특성을 예측할 수 있음을 보였다.
자전거 이용자가 안경 및 선글라스를 쓴 상태에서 마스크를 착용 할 때 여러 가지 불편함을 호소한다. 본 논문은 이러한 불편함을 보완하여 자전거 라이더들에게 필요한 일회용 미세먼지 마스크를 개발하는데 그 목적이 있다. 미세먼지 마스크의 특성상 일회성 정전기 발생 섬유와 마스크의 형태적 문제로 연구범위를 제한하고 기존 미세먼지 마스크를 간결한 제작공정으로 디자인한다. 이렇게 개발된 일회용 미세먼지 마스크는 세로방향 접힘으로 입 앞 마스크 내 공간을 충분히 확보하였고 거친 숨에도 입에 닿지 않게 접힘 부위형태가 유지 되게 하여 답답함을 최소화 하였다. 코지지대에 유선형 스폰지를 부착하고 안면 볼 부위를 일반마스크 보다 2.5cm 정도의 확장하여 측면 밀착성을 높였다. 또한 기존에 없던 일회용 미세먼지 스카프 마스크를 제작하여 안면과 목 부위 자외선을 차단하고 밀착성 높은 미세먼지 마스크를 개발하였다.
본 논문에서는 미세 방전가공(Electrical Discharge Machining; EDM) 기계를 위한 샌드위치 구조를 설계하기 위해 복합재료의 적층 순서, 두께, 그리고 리브의 형상 등을 고려한 파라메트릭 연구를 수행하였다. 샌드위치 구조는 면재인 섬유강화 복합재료와 심재인 레진 콘크리트 및 고분자 포움으로 이루어졌다. 컬럼은 정적 굽힘강성과 비굽힘강성을 높이기 위해 십자 리브를 가진 형상으로 설계하였으며, 적층 순서와 두께를 조절하였다. 베드의 경우 양방향의 강성을 동시에 향상시키기 위해 적층 순서와 리브 형상을 조절하였다. 최적의 고강성을 얻기 위하여 리브의 두께와 면재의 두께 등 설계 파라메터의 최적치를 제안하였다. 각 설계 파라메터의 변화에 따른 구조의 정적, 동적 강성의 변화를 확인하기 위해 유한요소해석을 수행하였으며, 진동 실험을 통하여 각 요소의 고유진동수와 감쇠비를 측정하여 비교하였다. 이러한 결과로부터 고정밀 미세 방전가공 기계 구조를 위한 최적의 형상조건을 제안하였다.
본 연구에서는 지도학습 기반 분할기법을 이용하여 단층 촬영된 단방향 복합재료의 유한요소모델링을 실시하였다. 우선, 단방향 복합재료의 형상 정보를 얻기 위해 Micro-CT 스캔을 수행하여 단방향 복합재료의 순수 체적(raw volume)을 획득하였고 여기에 몇 개의 단면을 선택하여 재료의 마이크로 구조인 섬유의 형상을 라벨링하였다. 이후 재료의 단면 이미지와 라벨링한 이미지를 각각 입출력으로 U-net 모델을 훈련시켰다. 이를 사용하여 선택되지 않은 단층촬영 이미지를 섬유형상을 구분하는 분할을 수행하였고 이렇게 생성된 3차원 정보를 이용해서 유한요소모델을 생성하였다. 최종적으로 단방향 복합재료 시편과 유한요소모델의 섬유체적비를 비교하여 제안된 방법의 적절성을 확인하였다.
본 연구에서는 콜타르 피치를 출발물질로 하여 KOH로 활성화시킨 슈퍼커패시터용 전극소재를 제작하였다. 콜타르 피치와 KOH의 활성화 비율을 1:4로 설정한 후 활성화 온도를 $600{\sim}900^{\circ}C$까지 $100^{\circ}C$ 단위로 4종류의 활성탄소를 제조한 후 피치계 활성탄소의 전기화학적 성능에 대한 KOH 활성화 온도의 영향에 관하여 고찰하였다. 또한 활성탄소의 형태학적 특성 변화를 흡착등온선과 FE-SEM을 통하여 분석하였다. 실험결과, 활성탄소의 커패시턴스는 전극 내 내부저항의 감소에 따라 증가하였는데, 이는 활성화 온도가 증가함에 따라 활성탄소 내 미세기공이 발달했기 때문이라 판단된다.
ECC는 모르타르 매트릭스에 약 2% 이내 체적비의 합성 섬유를 보강하여 1축 인장 하에서 변형률 경화 거동과 다수의 미세균열을 발현하도록 제조한 높은 연성의 시멘트 복합 재료이다. 최근 ECC를 적용하는 연구가 구조물 보수보강 공법, 현장 타설 및 프리캐스트화 공법 등 다양한 형태로 진행되고 있으며, 특히 연성이 요구되는 구조 부재에 적용하고 하는 시도가 끊임없이 이루어지고 있다. 이 연구에서는 성능 저하된 철근콘크리트(RC) 보의 구조 성능 및 균열 제어 성능을 개선하기 위하여 ECC와 고장력 철근을 함께 활용하는 보강 공법을 다루고 있다. 이를 위하여 RC 보실험체를 제작 실험하여 구조 성능과 파괴 형태 등을 연구하였다. 실험 결과, ECC와 고장력 철근으로 보강된 RC보는 우수한 균열 제어 성능과 더불어 휨 내하력 및 휨 강성이 크게 향상되는 것으로 평가되었다. 이 연구 결과는 ECC와 고장력 철근을 활용한 보강 공법의 설계 및 현장 적용을 위한 기초 자료로 활용될 것이다.
OXI-PAN fibers, Kynol fibers and rayon fibers were used as precursorsfor the preparation of activated carbon fibers (ACFs) by chemical activation with KOH at $800^{\circ}C$. The effects of different precursorfibers and fiber/KOH ratios on the final ACFs are discussed. The precursor fibers used are appropriate for the ACFs in a single stage pyrolysis process. The OXI-PAN fibers which were activated with KOH of 2.0M showed a specific surface area of $2328m^2/g$ however, loosed the fiber shape because of low yields. The Kynol fibers and Rayon fibers showed the high yields but the lower specific surface area of $900m^2/g$ and $774m^2/g$, respectively, at KOH of 1.5M. The OXI-PAN fibers which were activated with KOH of 1.5M have a specific surface area of $1028m^2/g$ and higher micro-pore volumes and lower yields rather than Kynol-1.5 and Rayon-1.5 samples. This phenomenon is because of higher chemical resistance of the Kynol and Rayon fibers rather than OXI-PAN fibers. However, the Kynol fibers were the best precursors on KOH activation at $800^{\circ}C$ considered carbon yields, surface areas and micropore volumes.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.