• Nuclear Engineering and Technology
• /
• v.41 no.5
• /
• pp.709-714
• /
• 2009

An ion implanter, which can serve as a metal-ion supply, has been constructed and performance tested. Copper ions are generated and extracted from a Bernas ion source with a heating crucible that provides feed gases to sustain the plasma. Sable arc plasmas can be sustained in the ion source for a crucible temperature in excess of $350^{\circ}C$. Stable extraction of the ions is possible for arc Currents less than 0.3 A. Arc currents increase with the induced power of a block cathode and the transverse field in the ion source. $Cu^+$ ions in the extracted beam are separated using a dipole magnet. A $20{\mu}A$ $Cu^+$ ion current can be extracted with a 0.2 A arc current. The ion current can support a dose of $10^{16}ions/cm^2$ over an area of $15\;cm^2$ within a few hours.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.10
• /
• pp.40-47
• /
• 2006

Optical performance of the mirror for satellite camera is highly dependent on the adhesive properties of its support. Therefore, in this paper, the adhesive properties of three kinds of space adhesives are investigated. For this purpose, the lap shear test is performed with Zerodur-to-metal lap shear specimen as well as metal-to-metal one. And it is also investigated whether reliable adhesive strength can be secured after the specific thermal cycle. Finally, the properties of three adhesives are compared with each other.

• Environmental Engineering Research
• /
• v.18 no.3
• /
• pp.145-150
• /
• 2013

Optimal preparation guidelines of a cathode catalyst layer by non-precious metal catalysts were evaluated based on electrochemical performance in single-chamber microbial fuel cells (MFCs). Experiments for catalyst loading rate revealed that iron(II) phthalocyanine (FePc) can be a promising alternative, comparable to platinum (Pt) and cobalt tetramethoxyphenylporphyrin (CoTMPP), including effects of substrate concentration. Results showed that using an optimal FePc loading of $1mg/cm^2$ was equivalent to a Pt loading of $0.35mg/cm^2$ on the basis of maximum power density. Given higher loading rates or substrate concentrations, FePc proved to be a better alternative for Pt than CoTMPP. Under the optimal loading rate, it was further revealed that 40 wt% of FePc to carbon support allowed for the best power generation. These results suggest that proper control of the non-precious metal catalyst layer and substrate concentration are highly interrelated, and reveal how those combinations promote the economic power generation of single-chamber MFCs.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.153-162
• /
• 2005

The structural specification of the rockfall prevention fence installed on the road section is computed according to the hypothetic rockfall energy, and the absorbable energy of the rockfall prevention fence is defined as the sum of the absorption energies of the wire rope, one of the components, the steel support and the wire netting. But the results of the field tests confirmed that the absorption energy of the rockfall prevention fence is not the sum of the energies sustainable by the components, but it is affected by the absorbable energy of part of the components. This shows there are problems with the method of computing the absorption energy of the rockfall prevention fence of the road. So in this paper, as a way of solving the problems, the effects of improving the performance through positional changes of the existing components and the effects of improving the performance through structural changes by expanded metal are checked through tests, and a plan was proposed to solve the problems with the standards of installing the conventional rockfall prevention fence.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.12
• /
• pp.1093-1100
• /
• 2014

The goal of this paper is to investigate preliminary the applicability of 3D printing technologies for the development of the hot bulk forming process and die. 3D printing technology based on the plastic material was applied to the preform design of the hot forging process. Plastic hot forging dies were fabricated by Polyjet process for the physical simulation of the workpiece deformation. The feasibility of application of Laser-aided Direct Metal Rapid Tooling (DMT) process to the fabrication of the hot bulk metal forming die was investigated. The SKD61 hot-working tool steel was deposited on the heat treated SKD61 using the DMT process. Fundamental characteristics of SKD 61 hot-working tool steel deposited specimen were examined via hardness and wear experiments as well as the observation of the morphology. Using the results of the examination of fundamental characteristics, the applicability of the DMT process to manufacture hot bulk forming die was discussed.

• Transactions of Materials Processing
• /
• v.20 no.7
• /
• pp.512-517
• /
• 2011

TRB(Tailor Rolled Blank) is an emerging manufacturing technology by which engineers are able to change blank thickness continuously within a sheet metal. TRB door inner panels with required larger thicknesses can be used to support localized high loads. In this study, the aluminum alloy 5J32 TRB sheet is used for a door inner panel application. The TRB material properties were varied by using three heat treatment conditions. In order to predict the failure of the aluminum TRB during simulation, the forming limit diagram, which is used in sheet metal forming analysis to determine the criterion for failure, was investigated. Full-field photogrammetric measurement of the TRB deformation was performed with an ARAMIS 3D system. A FE model of the door inner panel was created using Autoform software. The material properties obtained from the tensile tests were used in the numerical model to simulate the door inner of AA 5J32 for each heat treatment condition. After finite element analysis for the evaluation of formability, a prototype front door panel was manufactured using a hydraulic press.

• Toxicological Research
• /
• v.17 no.4
• /
• pp.255-265
• /
• 2001

Epidemiologic studies have demonstrated an association between short-term exposure to particulate air pollutants and increased mortality. However the biological mechanism underlying these associations have not been fully established and also the chemical and physical characteristics of the pollutant particles are not well understood. The metal constituents of air pollutant particles and their bioavailability are considered to Play an important role as possible mediators of Particle-induced airway injury and inflammation. Sprague-Dawley rat alveolar macrophage cells (NR8383) were exposed to airborne and acid-leached particulate matter (PM). Titanium oxide and nickel subsulfide were used as negative and positive controls. Particle-induced reactive oxygen species formation in cells was detected using the fluorescent probe 2',7'-dichlorofluorescin diacetate. Expression of TNF-$\alpha$ and IL-6 were measured by enzyme-linked immunosorbent assay, and PM-induced DNA double-strand breaks were determined with $\lambda$DNA/Hind III marker. Metals associated with air pollutant particles mediated intracellular oxidant production in alveolar macrophages, and the cytotoxicity and proinflammatory cytokine production induced by PM were associated with oxidative stress. The oxidants produced by air pollutant particles also are likely to induce DNA double-strand breaks. Our findings in alveolar macrophage cells exposed to PM and acid-leached PM support the hypothesis that metal components in urban air pollutants and their bioavailabilities might play an Important role in the induction of the adverse health effects.

• Journal of the Korean Chemical Society
• /
• v.57 no.5
• /
• pp.574-590
• /
• 2013

A new solid complexes of Ti(IV), Y(III) and Ce(IV) have been synthesized with ofloxacin. The formulae and structure of the complexes have been proposed in the light of analytical, spectral ($^1H$ NMR, IR and UV-Visible), magnetic, molar conductivities and thermal studies. The complexes are soluble in DMSO-$d_6$ and DMF. The measured molar conductance values indicate that, the three complexes are electrolyte in nature. The results support the formation of the complexes and indicated that ofloxacin reacts as a bidentate ligand chelate to the metal ion through the pyridone oxygen and one carboxylato oxygen. The kinetic parameters of thermogravimetric and its differential have been evaluated by using Coats Redfern (CR) and Horowitz-Metzeger (HM) methods. The thermodynamic data reflect the thermal stability for all complexes. The metal- ligand binding of the Ti(IV), Y(III) and Ce(IV) complexes is predicted using density funcational theory at the B3LYP-CEP-31G level of theory and total energy, dipole moment estimation of different Ti(IV), Y(III) and Ce(IV) ofloxacin structures. The biological activities of the ofloxacin, inorganic salts and their metal complexes were assayed against different bacterial species.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.4
• /
• pp.74-80
• /
• 2009

Effect of dye wastewater on heavy metal removal using carboxylated alginic acid bead was performed. When carboxylated alginic acid bead was used as support, effect of dye wastewater on adsorption of $Pb^{2+}$ and $Cu^{2+}$ ions was very small. Also, when $Pb^{2+}$ was coexisted with dye wastewater, adsorption process was almost completed within 2-3 hrs and $Pb^{2+}$ ions (50 ppm) was almost removed with 0.3g of bead. This result means that carboxylated alginic acid bead has effective adsorbent for heavy metal removal in dye wastewater.

• Applied Science and Convergence Technology
• /
• v.24 no.5
• /
• pp.172-177
• /
• 2015

We present disordered moth eye structures on curved surfaces fabricated by dry etching of thermally dewetted metal nanoparticles. This lithography-free fabrication allows the formation of subwavelength scale nanostructures on the strongly inclined surfaces such as ball lens as well as on the microlens arrays with low curvature. In particular, we found that the size and average distance of nanostructures are closely related to the inclined angle of the surface. Experimental results on oblique angle deposition of metal thin films followed by thermal dewetting also support these effects.