• Journal of the Korean Ceramic Society
• /
• v.28 no.11
• /
• pp.851-858
• /
• 1991

Spherical fine BaTiO3 powders with an average diameter of 0.3${\mu}{\textrm}{m}$ to 0.9${\mu}{\textrm}{m}$ are prepared at 100$0^{\circ}C$ by the ultrasonic spray pyrolysis of solutions containing Ba(NO3)2 and TiCl4. Experimental variables are adjusted to produce BaTiO3 powders and its effect on the phase, the size and the morphology of the particles are investigated by XRD, SEM, TEM. Each particle consists of small primary particles and has a hollow around its center. The dependence of particle diameters on the concentrations of source solutions indicates that metal salt precursors are dried to precipitate solid particles and decompose to form BaTiO3 phase without gas phase reactions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.3
• /
• pp.217-223
• /
• 1984

An attempt is made to predict the wear behavior of ion-nitrided metal, when wear arises from asperity interactions. The analysis demonstrates that wear mechanisms are not inconsistent with observed behavior, indicates and approaches to a better appreciation of the effects of such factors as nitrided layer formation and surface topographical features. It was found on ion-nitriding that penetration rate and case development are faster and wear properties of the final product are more improved than conventional gas and salt-bath methods of nitriding.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.198-201
• /
• 1994

Stability improvement of fragile LB films was attempted by polyion complexation of monolayers at the air-water interface and crosslinking of the resulting LB films. The spreading polymers were synthesized by radical copolymerization of monoalkyl itaconate with oligoethyleneglycol methyl vinylether, and poly(allylamine) was employed as the subphase polymer. Formation and characteristic of the monolayers were comfirmed by surface pressure-area($\pi$-A) isotherms. The two different polymers formed polyion-complexed monolayer through the formation of carboxylate/ammonium salt at the air-water interface. Y-type deposition occurred on solid substrates, and the transfer ratio was over 0.7. Pores (diameter, 0.1$\mu\textrm{m}$) of a membrane filter could be covered by polyion-complexed 6 layers. Interactions of the polymers with metal ions were investigated of the air-water interface and in the LB films. The structure change and macroscope morphology of the LB films were confirmed by FT-lR and SEM, respective1y.

• Journal of the Korean Society for Heat Treatment
• /
• v.5 no.1
• /
• pp.23-31
• /
• 1992

It is investigated that Fe-C-N compound layer, defusion layer, and induction hardened layer produced by nitrocarburizing blend heat treatment in austenitic temperature with high frequency induction heating of mild steel specimen sprayed sursulf salt-bath. As the temperature of blend-heat treatment got increased, the thickness and hardness of compound layer and diffusion layer were increased. Compound layer(max. $35{\mu}m$), diffusion layer (max. 2.5mm) and induction hardened layer were gained in the shortest time 10 sec and in the case of $1000^{\circ}C$ total hardness depth of those was about 3.5mm. When the blend-heat treated specimen was reheated, maximum hardness of compound layer was dropped more than that of the reheated compound layer after sursulf treated, whereas hardness of diffusion layer was increased.

• Analytical Science and Technology
• /
• v.13 no.6
• /
• pp.810-814
• /
• 2000

The open-chain hexadentate $N_4$, $O_2$ ligands 1, 15-bis(2-hydroxybenzyl)-2, 6, 10, 14-tetraazapentadecane (BSATPD. 4HCl) has been synthesized as its tetrahydro-chloride salt and characterized by EA, IR, NMR, and Mass spectrum. Its protonation constants ($logK_n{^H}$) and stability constants ($logK_{ML}$) for $Cu^{2+}$, $Ni^{2+}$, $Co^{2+}$ and $Zn^{2+}$ ions were determined in aqueous solution by potentiometry and compared with those of analogous $N_4$, $O_2$ ligands contain ethtylenic spacers or propylenic spacers, which make six-membered chelate rings between the aliphatic nitrogen atoms.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.5
• /
• pp.677-685
• /
• 1999

Aerosol mass size distributions were measured at Kosan, Cheju Island in April 1998 and their compositions were analyzed. Microorifice Uniform Deposit Impactor(MOUDI) was used to collect aerosols. Sulfate and ammonium ions were predominatly present at fine mode of the aerosols while nitrate, chloride, and metal ions were mostly at coarse mode. Based on the size distribution of nitrate, it is suggested that most nitrate were from gas to particle conversion on coarse particles. Non-sea salt(nss) fraction of sulfate accounted for more than 90% of total sulfate mass concentration. In general, ion concentrations in this study are lower than those measured at the same site from the previous studies. Ion balance and chloride ion levels indicates that there had been anthropogenic chloride emission sources near to the site during the measurements.

• Journal of the Korean Chemical Society
• /
• v.13 no.4
• /
• pp.303-307
• /
• 1969

The ammonium salt of Nitrosophenylhydroxylamine "called cupferron", is a well-known analytical reagent, which precipitates a great number of metal ions in acid medium. The electrode reduction velocities of cupferron at droping mercury electrode in various supporting electrolytes were measured by Delahay method. The free energy of activation and transfer coefficient for a given electrode reaction are computed from the corresponding current-voltage curve. The number of electrons involved in the rate determining step of the reduction of cupferron is calculated for solutions of various pH.

• YAKHAK HOEJI
• /
• v.35 no.5
• /
• pp.444-455
• /
• 1991

Two kinds of new lectin fractions (LOA-I, LOA-II) were obtained from loach (Misgurnus spp.) meat by 0.15 M NaCl extraction, salt fractionation, ion exchange and hydroxyapatite column chromatographies. On polyacrylamide gel electrophoresis, LOA-I exhibited one major and a few minor bands, but LOA-II exhibited three minor bands. The partially purified loach lectins agglutinated not only erythrocytes of human B and AB type, rabbit, dog, but also murine splenic lymphocytes. Agglutinability was relatively labile at various pH and stable at increasing temperature, but was not affected by tested several metal ions. By the sugar specificity test, D-glucosamine and metyl-$\beta$-galactopyranose inhibited agglutinating activity at a final concentration of 3 mM. The lectins contained relatively high amounts of aspartic acid, valine and leucine, but sulfur containing amino acids, cystein, methionine and isoleucine were not determined. LOA-I, LOA-II lectins were nonmitogenic toward murine lymphocytes.

• Journal of Powder Materials
• /
• v.11 no.3
• /
• pp.242-246
• /
• 2004

FePt nanoparticles for high-density magnetic recording media were synthesized by the simultaneous chemical reduction of Fe(acac) $_2$ and Pt(acac) $_2$ with 1,2-hexadecanediol as the reducing reagent. TEM images showed that the shape of as-synthesized FePt nanoparticle was spherical and average particle size was 3 nm. Also, SAD pattern showed that crystal structure was disordered FCC (face centered cubic). These FCC structured nanoparticles were transformed FCT (face centered tetragonal) structure by annealing at 55$0^{\circ}C$ for 30 min in Ar atmosphere. XRD analysis revealed that as-synthesized FePt nanoparticles were transformed from disordered FCC to ordered FCT. Finally, the coercivity of 2 kOe for FePt nanoparticles with FCT structure was obtained by VSM measurement.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.629-632
• /
• 1999

For replacing Li metal ai Lithium ton Bakery(LIB) system. we used carbon powder material which prepared by pyrolysis of phenol resin as starting material. It became amorphous carbon by pyrolysis through it\`s self condensation by thermal treatment. Amorphous carbon can be doped with Li intercalation and deintercalation because it has wide interlayer. however it has a problem with structural destroy causing weak carbon-carbon bond. So. we used ZnCl$_2$ as the pore-forming agent. This inorganic salt used together with the resin serves not only as the pore-forming agent to form open pores, which grow Into a three-dimensional network structure in the cured material, foul also as the microstructure-controlling agent to form a loose structure dope with bulky dopants. We analyzed SEM in order to find to different of structure. and can calculate distance of interlayer. CV test showed oxidation and reduction