• Bulletin of the Korean Chemical Society
• /
• 제32권5호
• /
• pp.1630-1634
• /
• 2011

Electroless plating of metallic nickel on carbon fiber surfaces was carried out to control specific electric resistivity of the fibers, and the effects of the nickel content and coating thickness on the electric properties were studied. The structural and surface properties of the carbon fibers were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The specific resistivity of the fibers was measured using a four-point probe testing method. From the XPS results, the oxygen and Ni atomic ratio of the fibers was greatly enhanced as the plating time increased. Additionally, it was observed that the specific electric resistivity decreased considerably in the presence of metallic nickel particles and with the formation of nickel layers on carbon fibers.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.96-101
• /
• 2011

The thin films of TiN have been used extensively as wear-resistant materials, for instance, such as tools of high-speed cutting, metal mold forming etc. In these days, because the thin films capable of being used more severe conditions are needed, the technologies of arc ion plating are tried to improve its characteristics. The purpose of this study is to investigate the characteristics of thin films of (Ti,Cr)N compared with those of TiN. The method of arc ion plating, which is known as showing good tight-adherence and productivity, was used. After manufacturing thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) with change of Cr in (Ti,Cr) target, atomic concentration, structure, size of crystallite, residual stress and surface roughness of thin films on substrate were investigated. As the results, it was confirmed that Cr atomic concentrations of thin films were proportionally changed with Cr atomic concentrations of target, and thin films of ($Ti_{1-x}Cr_{x}$)N (x=0~1) showed NaCl type and CrN existed as solid solution to TiN.

• 한국환경과학회지
• /
• 제17권3호
• /
• pp.335-342
• /
• 2008

This study based on electro-coagulation & oxidation reaction is applied to wastewater treatment. Electro-oxidation reaction is used to remove cyanide(CN) which is contained in plating wastewater. Cyanide is transferred by gases such as $NH_3,\;NO_x,\;CO_2$. Analysis result and removal efficiency of Cyanide which is contained in heavy metal wastewater of plating plant, are shown as following paragraph. In electrode arrangement experiment, removal efficiency of carbon electrode(-)/STS316L electrode(+) arrangement method is superior to carbon electrode(-)/carbon electrode(+) arrangement method. Removal efficiencies of cyanide in different HRT such as 30 min, 45 min, 60 min, 75 min and 90 min are 85.5%, 93.1%, 98.0%, 98.7% and 99.4% respectively in carbon electrode(-)/STS316L electrode(+) arrangement method. Finally we can estimate the critical point at HRT of 60 min which the variation of removal efficiency is decreased and HRT to obtain removal efficiency of less than 1 mg/LCN is minimum 90 min.

• 청정기술
• /
• 제20권2호
• /
• pp.136-140
• /
• 2014

본 연구에서 폴리프로필렌을 모재로 사용하여 Co/Ni/P/Mn 4가지 금속을 무전해도금 방법으로 코팅하였다. 이 때 도금욕의 시약의 양을 조절함으로써 폴리프로필렌 위에 도금된 금속의 조성을 다르게 조정하였다. 이러한 조건으로 만들어진 도금 금속에 대하여 두께, 전기적 표면 저항, 주사형 전자현미경을 사용한 표면상태, 에너지 분산형 분석기를 통한 금속조성을 측정하였다. 인 함량이 높을수록 전지저항이 커지는 것이 관찰되어 인 함량과 전지전도성간의 상관성이 있는 것이 관찰되었다. 또한 코팅 금속의 수용액에서의 부식성을 3.5 wt% 염화나트륨 용액과 5.0 wt% 황산용액에서 비교한 결과 인을 많이 포함할수록 내식성이 강함을 알 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제3권2호
• /
• pp.9-15
• /
• 1992

Electroless copper plating method using an alkaline bath have been employed in copper coating of the (LM)Ni4.5Co0.1MnO.2A10.2 hydrogen storage alloy powders for electrode preparation. The plating were conducted without any pretreatment of alloy powders. For the preparation of the electrodes, about 0.12g of the copper coated alloy powder (copper to alloy ratio 1/3 by weight) was compacted with pressure of 6 tons/cm2 at room temperature. The disk-type compacts had a diameter of 10mm and thickness of about 0.24mm. The electrode characteristics were examined through SEM observations and electrochemical measurements in a half cell. The electrochemical measurement showed that the maximum discharge capacity of the electrodes prepared by using alkaline bath were 245mAh per gram of coated alloy (327mAh per gram of alloy) and appeared a considerable degradation with increasing number of cycles. The decrease of the discharge capacity after 100 cycles was about 30% It can be suggested that, with a slight of improvement, this electroless copper plating method could be applied to the preparation of the rare earth-nickel based alloy electrode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.252-255
• /
• 2004

반도체는 high integrated, high speed, low power를 위하여 design 뿐만 아니라 재료 측면에서도 많은 변화를 가져오고 있으며, RC delay time을 줄이기 위하여 Al 배선보다 비저항이 낮은 Cu와 low-k material 적용이 그 대표적인 예이다. 그러나, Cu 배선의 경우 dry etching이 어려우므로, 기존의 공정으로는 그 한계를 가지므로 damascene 또는 dual damascene 공정이 소개, 적용되고 있다. Damascene 공정은 절연막에 photo와 RIE 공정을 이용하여 trench를 형성시킨 후 electrochemical plating 공정을 이용하여 trench에 Cu를 filling 시킨다. 이후 CMP 공정을 이용하여 절연막 위의 Cu와 barrier material을 제거함으로서 Cu 배선을 형성하게 된다. Dual damascene 공정은 trench와 via를 동시에 형성시키는 기술로 현재 대부분의 Cu 배선 공정에 적용되고 있다. Cu CMP는 기존의 metal CMP와 마찬가지로 oxidizer를 이용한 Cu film의 화학반응과 연마 입자의 기계가공이 기본 메커니즘이다. Cu CMP에서 backside pressure 영향이 uniformity에 미치는 영향을 살펴보았으며, electrochemical plating 공정에서 발생하는 hump가 CMP 결과에 미치는 영향과 dishing 결과를 통하여 그 영향을 평가하였다.

• 한국재료학회지
• /
• 제5권8호
• /
• pp.1013-1019
• /
• 1995

본 연구에서는 무전해 도금범으로 polyester film 상에 Co-Ni-P 박막을 석출시키고, pH, 온도 그리고 도금용액의 농도에 따른 도금속도 및 석출된 도금박막의 합금조성과 합금조성에 따른 자기적 특성을 고찰하였다. 무전해도금의 석출속도는 pH 8.5, 온도 90℃일때 가장 좋았으며, 자기적 특성도 이 때가 가장 좋았다. 합금조성은 pH와 착화제의 농도에 따라서는 크게 변화하였으나, 그 밖의 인자들에 의해서는 변화하지 않았다. 최적조건에서 만들어진 박막의 합금조성은 코발트가 78%, 니켈이 16%, 인이 6%였고, 보자력은 370 Oe, 각형비는 0.65였다. 박막은 합금조성에 따라 경질자성막과 연질자성막의 두가지 형태로 변화했고, 니켈이 30% 이상 공석(共席)되었을 때, 연질자성막으로 되었다. 연질자성막일때, 합금박막의 결정구조는 니켈이 강하게 배향된 비정질 형태를 나타냈고, 경질자성 막일때는, 코발트(101)과 (100)면으로 배향된 α-코발트의 hcp 결정구조를 나타내었다.

• 한국표면공학회지
• /
• 제28권2호
• /
• pp.83-91
• /
• 1995

A new method for preparation of thin nickel foam for Ni-MH battery was investigated. In this method, fine graphite powders of $1\mu\textrm{m}$～$2\mu\textrm{m}$ diameter were pasted into pores of thin polyurethane foam film in order to supply electric conducting seeds for nickel deposition by electroless plating reaction. After electroless plating, remaining polyurethane foam was removed chemically by organic solvent treatment and graphite particles also removed by ultrasonic cleaning. Porosity of formed nickel foam was about 85% During electroplating, porosity of the nickel foam decreased less than 5% up to $30\mu\textrm{m}$ coating thickness. And then it was electroplated and heat-treated to improve mechanical strength and ductility. Finally, thin nickel foam for Ni electrode of Ni-MH battery with 80% porosity and $350\mu\textrm{m}$～X$400\mu\textrm{m}$ thickness was obtained.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.119-123
• /
• 2006

The ionic-polymer-metal-composite actuators have the best merit for bio-mimetic locomotion because of their large bending performance. Especially, they have the advantage for mimicking a fish-like motion because IPMCs are useful to be actuated in water. So we have developed IPMC actuators with multiple electrodes for realization of biomimetic motion. Generally, the IPMC actuator has been fabricated in electroless plating technique, while it needs very long fabrication time and shows poor repeatability in the actuation performance owing to the variables in chemical fabrication process. Therefore, the novel fabrication methods were investigated by combining electroless plating and electroplating techniques capable of patterning precisely. On the whole, two different methods were compared and analyzed with similar thickness level of Platinum electrodes. Present results show that mixing chemical reduction and electroplating can be a promising candidate for electrode patterning.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.11-17
• /
• 2001

Industrial use of physical vapor deposition(PVD) has been widely expanded during last two decades, and in the mean time plasma assistance in PVD has become an essential tool in preparing compound films with dense microstructure. The principles of electron beam-based plating, balanced and unbalanced magnetron sputtering and cathodic arc deposition. consisting three basic configuration of plasma assisted PVD(PAPVD)process, were reviewed. Recent technical development in PVD coating process were discussed. This paper tries to show tendency for developing new coating film on cutting tools.