• Journal of Mechanical Science and Technology
• /
• 제15권12호
• /
• pp.1676-1682
• /
• 2001

This work deals with the electrical conductivity of dielectric and cobalts percentage on output parameters such as metal removal rate and surface roughness value of sintered carbides cut by wire-electrical discharge machining (WEDM). To obtain a precise workpiece with good quality, some extra repetitive finish cuts along the rough cutting contour are necessary, Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a higher metal removal rare as the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. To obtain a good surface equality without crack, 4 finish-cuts were necessary reducing fille electrical energy and the offset value.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.100-105
• /
• 1999

This work analyses the effects of electrical conductivities of dielectric and cobalt amount on output parameters such as metal removal rate and the surface roughness value of cemented carbides cut by wire electrical discharge machining(W-EDM). Especially, the cracking behaviour of W-EDM machined surface and optimal machining condition of three kinds of cemented carbides, which have different chemical composition of tungsten carbide and cobalt are also tested. Experimental result shows that increases in cobalt content and electrical conductivity of the dielectric affect the metal removal rate and substantially worsen the final surface quality as a greater quantity of solidified metal deposits on the eroded surface.

• 자원환경지질
• /
• 제19권2호
• /
• pp.85-96
• /
• 1986

The Bupyeong Silver mine which is located approximately 35km west of Seoul is currently the leading silver producer in Korea. The deposits occur as stockwork deposits hosted in Jurassic pyroclastic rocks. Occurrences of ore deposits and mineral paragenesis suggest a division of mineralization into four stages: Stage I, deposition of iron oxide and base metal sulfides; Stage II, deposition of tin oxide and silverm inerals; stage III, deposition of native silver and other silver minerals; Stage IV, formation of pyrite bearing siderite veinlets, Silver minerals in ore are native silver, argentite, freibergite, pyrargyrite, canfieldite, polybasite, dyscrasite and Ag-Fe-S mineral. The most important silver mineral is native silver among them. Chemical composition of important silver minerals were determined by electron probe microanalyser. Assay, size and modal analyses for floatation products were carried out. In floatation products, relative proportion of native silver for total important silver minerals have following ranges: feed, 64.7 to 74.74 wt.%; A-cleaner concentrate, 80.58 to 98.79 wt.%; and final tailing, 28.12 to 72. 57 wt. %. Average degree of liberation for native silver in feed and A-cleaner concentrate are 60.49% and 77.57% respectively. Negative relationship can be recognized between native silver and argentite in their abundance and behavior in floatation precesses.

• 한국재료학회지
• /
• 제19권6호
• /
• pp.319-324
• /
• 2009

The deposition behavior and structural and magnetic properties of electroless Co-B and Co-Fe-B deposits, as well as the amorphous ribbon substrates, were investigated. These Co-based alloy deposits exhibited characteristic polycrystalline structures and surface morphology and magnetic properties that were dependent on the type of amorphous substrates. The catalytic activity sequence of the amorphous ribbon electrodes for anodic oxidation of DMAB was estimated from the current density-potential curve in the anodic partial electrolytic bath that did not contain the metal ions. Both the deposition rate and potential in the initial region were obtained in order of the catalytic activity, depending on the alloy compositions of the substrates. The deposition rate linearly varied against the deposition time. The initial deposition potential may have also determined the structural and magnetic properties of the deposit based on the thickness of ${\mu}m$ order. Furthermore, a basic study of the electroless deposition processes on an amorphous ribbon substrate has been carried out in connection with the structural and magnetic properties of the deposits.

• 자원환경지질
• /
• 제43권3호
• /
• pp.235-248
• /
• 2010

광물찌꺼기의 특성평가 방법의 표준화를 위하여 21개 광산을 대상으로 총 26개의 광물찌꺼기를 채취하여 광물찌꺼기의 비중, paste pH, 입도, 광물조성 및 중금속 함량을 분석하였다. 광물찌꺼기의 비중은 2.61-4.31(평균 3.04)의 범위를 보이며, 입도분포는 모래와 실트의 함량이 우세한 것으로 나타났다. 광물찌꺼기의 paste pH는 2.1-9.5의 범위를 보이는데, 정마그마광상, 스카른광상 및 열수교대광상의 경우에는 7.1-9.2, 그리고 열수맥상광상의 경우에는 2.1-9.5의 분포를 보인다. 열수맥상광상 유형은 paste pH에 따라 paste pH>7.0, 4.0

• 한국세라믹학회지
• /
• 제48권1호
• /
• pp.20-25
• /
• 2011

Since 1980's, many mines have been closed and abandoned due to the exhaustion of deposits and declining prices of international mineral resources. Because of the lack of post management for these abandoned mines, Farm land and rivers were contaminated with heavy metal ions and sludge. We studied on the solidification/stabilization of heavy metal ions, chromium ions and lead ions, using magnesia-phosphate cement. Magnesia binders were used calcined-magnesia and dead-burned magnesia. Test specimens were prepared by mixing magnesia binder with chromium ions and lead ions and activators. We analyzed the hydrates by reaction between magnesiaphosphate cement and each heavy metal ions by XRD and SEM-EDAX, and analyzed the content of heavy metal ions in the eruption water from the specimens for the solidification and stabilization of heavy metal ions by ICP. The results was shown that calcined magnesia binder is effective in stabilization for chromium ions and dead-burned magnesia binder is effective in stabilization for lead ions.

• 한국표면공학회지
• /
• 제34권6호
• /
• pp.537-544
• /
• 2001

In the present study, tin-zinc alloys were coated on a cold-rolled steel sheet with variations of electrolyte concentration, additives quantity and current density employing the Hull cell and circulation cell simulator. With an addition of additives of 2m1/L, tin-zinc deposits containing 10 to 40 percent Zn revealed a good surface appearance with weak acidic electrolytes. The organic additives suppressed the Sn deposition rate and thus increased the zinc contents in tin-zinc coating layers. The zinc contents in the tin-zinc coating layers depended almost linearly on the concentrations of metal ions of tin and zinc. Temperature of the electrolyte affected the composition tin-zinc coating layer. However, the concentration of complexants revealed little effectiveness. The surface morphology of tin-zinc coating showed dense tin and zinc phases with fine equiaxed grains with the high current density.

• 자원환경지질
• /
• 제2권3호
• /
• pp.47-57
• /
• 1969

The Yeonhwa Lead and Zinc Mine is located in northern part of Kyeongsang-Buk-Do, Korea, and is economically most important mine because it produces most part of the output of lead and zinc minerals in the country. Ore deposits of the mine are localized in the Pungchon Formation and several limestone seams of upper Myobong Formation in Cambrian Age. Ore solution ascended along the fractures of N-S, NE-SW or NW-SE trends and along slate and limestone boundary, and then replaced selectively limestone to make ore bodies. Skarn minerals are consisted of hedenbergite, diopside, and main sulfide mineral orebodies are composed of galena, zincblende, pyrrhotite, pyrite and a minor amounts of arsenopyrite and chalcopyrite. Metal ratio, ${\rho}_{Pb}={\frac{Pb(%)}{Pb(%)+Zn(%)}}{\times}100$, illustrates the zona I arrangements of some ore bodies. It will be inferred the flow trending of ore solution and the process reaction with adjacent country rocks. The sub-divided formations of the Pungchon limestone and Myobong slate are very useful as a criteria for detecting probable ore location. Rhodochrosite veins are good evidence for searching of ore location, especially on Pb-rich ore bodies.

• 자원환경지질
• /
• 제31권5호
• /
• pp.365-374
• /
• 1998

Economic U- and Th-bearing pegmatite deposits occur in the Kyemyeongsan Formation, and are spatially closely associated with the Carboniferous alkali granite. The pegmatite is lithochemically alkaline and peralumious, and consists mainly of potassic feldspar and quartz with allanite and U- and Th-bearing minerals. Paragenetic stages of mineralization in the pegmatite are divided as follows: early silicate mineralization, main rare metal mineralization, and late silicate mineralization. Thorite, euxenite, fergusonite and uranpyrochlore are the predominant U- and Th-bearing minerals. Both the enrichments of Nb, Y, Th, U, and Ta and the depletions of Hf, Ba, and Rb in the pegmatite were resulted from magmatic differentiation. The increases of Na and Ca in uranpyrochlore, of Th and U in fergusonite, of Si, Th, U and Pb in thorite, and of Nb and Y in euxenite were possibly resulted from both later internal fractionation and hydrothermal alteration. The variation of chemical composition in a mineral species reflects the different pysico-chemical conditions during the crystallization.

• 대한기계학회논문집A
• /
• 제27권10호
• /
• pp.1800-1808
• /
• 2003

This work deals with the electrical conductivity of dielectric on output parameters such as metal removal rate and surface roughness value of a carbon steel(SM25C) and sintered carbides cut by wire-electrical discharge machining(W-EDM). Dielectric has several functions like insulation, ionization, cooling, the removal of waste metal particles. The presence of minute particles(gap debris) in spark gap contaminates and lowers the breakdown strength of dielectric. And it is considered that too much debris in spark gap is generally believed to be the cause of arcing. Experimental results show that increases of cobalt amount in carbides affects the metal removal rate and worsens the surface quality as a greater quantity of solidified metal deposits on the eroded surface. Lower electrical conductivity of the dielectric results in a lower metal removal rate because the gap between wire electrode and workpiece reduced. Especially, the surface characteristics of rough-cut workpiece and wire electrode were analyzed too. Debris were analyzed also through scanning electron microscopy(SEM) and surface roughness tester. Micro cracks and some of electrode material are found on the workpiece surface by energy dispersive spectrometer(EDS).