• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.189-193
• /
• 2006

Experiments were performed to investigate the melting characteristics of pellet fuel made of LDPE and PP for a waste plastic firing boiler. Pellet fuel in a burner goes through conduction, convection and radiation transferred from flame in a furnace, and complex thermo/chemical processes. To figure out effects of ambient temperature and size of pellet on melting time pellets with a diameter from 5 mm to 40 mm were made to contact high temperature flue gas generated by a LNG firing pilot burner. Though melting processes of plastics include complicated heat transfer in a burner, parameters are limited to flue gas temperature and size for the simplicity in this study. From the results, melting times of LDPE and PP with a diameter of 5mm are 63 and 62 secs respectively at 600 $^{\circ}C$ while 677 and 583 sees respectively for a diameter of 40 mm. At $900^{\circ}C$, melting times of LDPE and PP with a diameter of 5mm are 21 and 24 sees respectively while 408 and 337 secs respectively for a diameter of 40 mm. It is found that melting time of LDPE is longer than that of PP, and melting times of both in general increase with diameter of pellets. It is thought melting is dependent mostly on melting temperature of plastic. It is expected melting times obtained from the study might be taken into account in designing a pellet firing burner for a boiler

• 한국안전학회지
• /
• 제19권1호
• /
• pp.60-65
• /
• 2004

The PVC insulated flexible cords are used mainly as power supply cords of electric appliance. This electric wire is a stranded wire consisted of dozens of strands. In case stranded wires are disconnected by mechanical stress, it weakens electrically. Finally, the over current flows through stranded wires, and electrical fire occurs. In this study, we analyzed the melting properties of strands by over current, such as melting process, melting current and melting time. And we analyzed that quantity of heat for melting, a cross sectional structure, and surface structure by optical microscope and SEM. As analysis results, melting time decreased as melting current increased. And quantity of heat for melting was low, too. From the cross sectional structure of melted wire, when a melting current low and melting time long, it was found that the dendrite structure grew. However, the dendrite structure is hard to grow because growing time is not enough when a melting current high and melting time short.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권1호
• /
• pp.36-44
• /
• 1995

Melting characteristics of unrestrained liquid ice in a rectangular vessel with heated top wall were investigated experimentally. The liquid ice, a mixture of ice particles and ethylene-glycol aqueous solution, was adopted as a testing material. During the melting process the liquid ice was drawn by buoyancy to the heated top wall of the rectangular vessel where close-contact melting occured. The melting behavior and melting rate of the liquid ice as well as local/mean heat-transfer coefficient at the heated top wall were observed and measured under a variety of conditions of heat flux and various initial concentration of the aqueous binary solution. It was found that the heat transfer of the heated top wall is remarkably promoted by the close-contact melting, and that the dendritic frozen layer at the lower interface of the liquid ice is formed. Photographic evidence demonstrated that plumes containing solute-rich liquid issued from isolated chimneys within the liquid ice layer where segregation of interstitial channel took place.

• 한국안전학회지
• /
• 제28권5호
• /
• pp.15-20
• /
• 2013

This paper dealt with melting characteristics of low-voltage miniature cartridge fuse used for 220 V electronic equipment. The experimental sample is low-voltage miniature cartridge fuse with rating of 250 V(3A) and size of $5{\times}20$ mm. In order to evaluate melting and scattering characteristics of the fuse, we applied to 8/20 ${\mu}s$ surge current, overload current and external thermal stress such as flame of fire. From the experimental results, the fuse element was melted and scattered by applied surge current(above 0.79 kA) and overload current(above 4.5 A). It was also attached to the inner surface of the fuse tube. The fuse element was attached as a thin film on inner surface of fuse tube when large surge current was applied. It was confirmed, however, the fuse element was not changed by external thermal stress such as flame and hot-air.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.356-359
• /
• 1997

The Effects of different melting temperature and holding time in the melting temperature on J$\sub$c/ of YBa$_2$Cu$_3$O$\sub$x/ based superconducting bulk using MPMG process were investigated. the value of critical current density was the largest at l120$^{\circ}C$, the melting temperature which is appointed to the mid point of (Y$_2$BaCuO$\sub$5/ + Liquid)region. With the melting temperature in which the value of J$\sub$c/ is the largest, J$\sub$c/ was again measured to see whether the holding time at this proper melting temperature has the effect on the critical characteristics. From the result above it was concluded that the melting temperature and holding time were important to improve the J$\sub$c/ and the formation of the Y$_2$BaCuO$\sub$5/. In this paper, the melting temperature obtained was l120$^{\circ}C$ and propel holding time could be obtained as 20 minute and the more holding time was not effective in the J$\sub$c/ improvement as well as the formation of Y$_2$BaCuO$\sub$5/.

• 한국전기전자재료학회논문지
• /
• 제33권6호
• /
• pp.515-520
• /
• 2020

The Ti₃SiC₂ MAX phase was synthesized by arc-melting process under three different processing times. We confirmed that the reaction between the TiC_X phase and Ti-Si liquid phase is important for the synthesis of the Ti₃SiC₂ MAX phase. Results suggest that the Ti₃SiC₂ MAX phase decomposed when the arc-melting time was greater than 80s. Herein, we aim to determine the detailed parameters for the reported arc-melting process, which can provide useful insights on the synthesis of the Ti₃SiC₂ MAX phase by arc-melting process. Furthermore, we compared the electrical characteristics and densities of the three samples.

• Korea-Australia Rheology Journal
• /
• 제13권2호
• /
• pp.89-95
• /
• 2001

Effects of particulate size and frictional characteristics were examined on the melting behavior of PP(polypropylene) in a twin screw extruder. Powder and pellet types of PP were used and each component was blended with PE(polyethylene) wax and clay, respectively. It was observed that small size particulates, 1.e. powder systems exhibit accelerated melting behavior; and it was also found that the abrasive auditive acts as an effective agent for fast melting of PP powder. Retardation of melting due to the reduced friction was observed in both types of PP, contrary to the result found in a batch mixer. The tendency observed in variation of torque and exit temperature was explained in terms of frictional effect and length of compacted region formed during evolution of melting.

• 한국컴퓨터정보학회논문지
• /
• 제12권4호
• /
• pp.201-207
• /
• 2007

제조업에서는 2개 이상의 상관이 있는 품질특성치를 동시에 감시하거나 관리를 하기 위한 필요성이 많이 제기되고 있다. 하지만 복수의 품질특성치를 각각 독립적으로 감시하면 판단의 오류가 발생될 수 있다. 복수의 품질특성치를 동시에 감시하고자 할 때 $X^2$ 또는 $T^2$와 같은 다변량 관리도가 사용되어질 수 있다. 본 논문에서는 다수의 품질특성치를 갖는 용해공정에서 조기에 이상 징후를 파악하기 위하여 다변량 관리도를 이용한 조기경보 시스템을 구현하였다. 용해공정에서 상관성이 있는 다수의 품질특성치를 동시에 관리하기 위해 개발된 이 모듈은 용해공정의 통계적 공정관리 활동에 효율성 및 효과성을 향상시켜 주었다.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 2001년도 총회 및 춘계학술발표회
• /
• pp.30-33
• /
• 2001

Melting is one of the most effective treatments for stabilizing heavy metals and also creates high value by-products. In this study, authors evaluated the leaching characteristics of heavy metals in melting slag obtained from incinerator ashes. In order to evaluate the environmental compatibility of the recycled melting slag, the samples analysed various leaching tests of heavy metals were raw incinerator ashes, melting slag and the construction materials recycled from melting slag. As the results: (1) The leaching concentrations of tile melting slag were lower than those of the raw incinerator ashes in the experiment performed in accordance with Korea Standard Leaching Test (KSLT). (2) The result of leaching test with the method of RG Min-StB 93. FGSV Forschungsgesellschaft fur Stra $\beta$ en- und Verkehrswesen) met the requirements in German. (3) The compressive strengths of mortar samples used for evaluating the feasibility of recycling the melting slag as construction materials also showed the suitable range for recycling (4) Melting slag was considered the stable materials with respect to the chemical stability against chemical solutions with various pH conditions.

• 한국지하수토양환경학회지:지하수토양환경
• /
• 제6권1호
• /
• pp.23-31
• /
• 2001

용융처리는 중금속을 안정화시키는 효과적인 방법의 하나이며, 또한 고가의 부산물을 생산해낸다. 본 연구에서는 소각재를 용융하여 얻은 슬래그의 중금속 용출특성을 평가하고자 한다. 슬래그를 재활용하는데 있어서 환경적인 적합성을 평가하기 위하여 소각재, 슬래그 및 슬래그를 재활용재로 하여 제조한 건설재료에 대한 용출시험을 수행하였다. 시험결과는 다음과 같다. (1) 국내표준용출시험법(KSLT)에 의해 시험한 슬래그의 중금속 용출농도는 소각재의 용출농도보다 낮은 값을 나타냈다. (2) 장기용출시험법에 의해 평가한 슬래그의 중금속 용출농도도 KSLT의 기준을 만족했다. (3) 슬래그의 건설재료로서의 사용성을 평가하기 위해 만든 모르타르 공시체의 용출결과, 슬래그를 재활용재로서 사용하는데 있어서 중금속 용출 측면에서 적합하다고 사료된다. (4) 독일의 소각재 재활용을 위한 가이드라인인 RG Min-StB 93, FGSV에서 제시하는 방법에 의해 시험한 결과, 본 슬래그의 용출농도는 독일의 규제기준을 만족하였다.