• Journal of Biosystems Engineering
• /
• v.27 no.5
• /
• pp.409-416
• /
• 2002

This study was conducted to develop a vehicle, leading or following a worker at a certain distance to assist laborious transporting works in greenhouses. A prototype vehicle, which consisted of the rear driving, the front steering and the console units, was designed and tested in the ideal indoor conditions. Results of this study were summarized as following: 1. The driving unit was designed to travel at the speed ranges of 0.3∼0.8 m/sec depending on the operating modes with a maximum payload of 100 kg. 2. The console unit consisted of a main-board including a 80C196KC microprocessor and peripheral devices, a power-board and safety interlock. Worker-leading, and following modes were available in automatic and manual modes. 3. Steering was achieved by turning the steering motor against the sensed direction. Proper steering angles for correcting travel direction were determined as 5 and 9 degrees when sensing cultivation beds and plants, respectively.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.385-390
• /
• 2000

The heat pump is one of heating and cooling systems driven by electricity using natural energy as a heat source. The heat pump system was mainly adopted to a cooling system or a refrigeration system. In regions with a large amount of electricity, it is used as a heating system or a heating and cooling system of houses, buildings and agricultural facilities. During cold weather, air source heat pumps do not work well because of some technical problems, such as frosting on evaporator coil when outside air temperature is below -5$^{\circ}C$. In this research, the heat regenerative technology was employed to eliminate the frosting on evaporator coil and improve the COP of the heat pump system. This fiber belt heat regeneration system(FBHRS) has very simple structure consisting of a geared motor and a porous fiber belt passing through alternatively between cold and warm air duct. The laboratory test showed that the heat pump system with a FBHRS yielded an impressive COP higher than 3.5 at the outside air temperature of -7$^{\circ}C$ in heating mode.

• Journal of Drive and Control
• /
• v.16 no.4
• /
• pp.74-79
• /
• 2019

In this study, an edible fresh corn harvest testing machine was designed and manufactured. And harvesting performance was analyzed through the field test. The testing machine is of the tractor attached type. It is connected to the tractor PTO shaft to transfer power to the each part of the harvesting machine. And it harvests fresh corn by one row through the processes of cutting, stem crushing, detaching, and collecting. The performance test was performed at PTO speed (540, 750, 1050 rpm, respectively), working speed (0.1, 0.15, 0.2 m/s, respectively), and cropping cultivation (row spacing·hill spacing 70·25 cm, 70·40 cm, 90·30 cm, respectively). The performance test was repeated three times in the 15 m section. The detachment loss ratio, uncollected crop ratio, damage ratio, and harvest ratio were analyzed. As a result of the performance test, it was analyzed that the PTO speed 540 rpm, running speed of 0.1 m/s, and row spacing·hill spacing 70·40 cm were the optimal condition.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.698-706
• /
• 2000

It is very difficult to mechanize tomato harvesting because identifying a tomato partly covered with leaves and stalks is not easy. This research was conducted to develop tomato harvesting robot which can identify a target tomato, determine its three dimensional position, and harvest it in a limited time. Followings were major findings in this study. The first visual system of the harvesting robot was composed of two CCD cameras, however, this could not detect tomatoes which are not seen on the view finder of the camera especially those partly covered by leaves or stalks. The second visual device, combined with two CCD cameras and pan/tilt procedures was designed to minimize the positioning errors within ${\pm}10mm$, but this is still not enough to detect tomatoes partly covered with leaves etc. Finally, laser distance detector was added to the visual system that could reduce the position detecting errors within 10mm in X-Y direction and 5mm in Z direction for the partly covered tomatoes.

• Journal of Biosystems Engineering
• /
• v.28 no.3
• /
• pp.245-252
• /
• 2003

This study was investigated the possibility of measuring chlorophyll in paddy crops using two kinds of chlorophyll meters(SPAD-502, Field Scout). The results of correlation analysis showed the 0.7758(r$^2$) relationship between the chlorophyll contents of paddy leaves measured by SPAD and spectrophotometer. It indicates that chlorophyll content in paddy crops could be measured using the SPAD. Considering the data of the SPAD and Field Scout there was significant difference between their chlorophyll contents measured by the SPAD and Field Scout. Likewise, such results were consistent with the corrected data using light intensity. According to the results, it can be concluded that it is difficult to describe the rice chlorophyll measured by the Field Scout more accurately than the SPAD when using one standard spectrum and another spectrum for reflectance measuring. The chlorophyll variance measured at a research institute and a farmer's field revealed that the output of SPAD was more reliable than that of the Field Scout.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.307-312
• /
• 2000

This study was carried out to develop an automatic grafting system suitable for fruit-vegetable seedlings. The study consisted of two research sections: 1) development of a medium-sized, low-cost automatic grafting system for cooperative farms and commercial seedlings production company, and 2) commercializing research for prototype development based on the above concepts. The grafting robot developed in this research can be described as follows, a. Developed grafting robot can cover the whole operations for grafting scion and rootstock, only if operator provides scion and rootstock tray. b. Five seedlings can be grafted at one time, and about 1,200 seedlings can be grafted in one hour. c. The success ratio of mechanical grafting scion and rootstock with ceramic pin bonding provided by the holder is more than 95% when the conditions of seedlings are satisfied. d. The grafting efficiency has improved over 10 times compared with manual work, and the grafting cost generated 44% savings.

• Agricultural and Biosystems Engineering
• /
• v.2 no.1
• /
• pp.31-36
• /
• 2001

Based on the viscous flow characteristics of gas through capillary tube, a simple and cheap gas mixing system was developed for controlling gas compositions in CA chambers. The gas flow rate through capillary tube had a linear relationship with pressure, (length)$^{-1}$ and (radius)$^4$ of capillary tube, which agreed well with Hagen-Poiseuille’s law. The relationship between flow rate and combined parameters was described as Q=0.000209724($\pi$ r$^4$P/$\mu$L) and the coefficient of determination was 0.9984. The developed system could control gas concentrations in CA chambers within $\pm$0.3% deviation compared to the preset concentrations. It was possible to predict the required time and required gas flow rate for exchanging the gs in CA chamber to a certain concentration of gas by using the mathematical model developed in this study.

• Journal of Biosystems Engineering
• /
• v.25 no.5
• /
• pp.415-420
• /
• 2000

It is very difficult to mechanize tomato harvesting because identifying a target tomato which is partly covered by leaves and stalks is not easy. This research was conducted to develop tomato harvesting robot which can identifying a target tomato, determining its dimensional position, and harvesting it in a limited time. Followings were major findings in this study. The first visual system of the robot was composed of two CCD cameras, however, which could not detect tomato not placed on the center of lens and partly covered by leaves or stalks. Secondary visual device, combined with two cameras and pan tilting was designed which could decreased the positioning errors within $\pm$10mm but still not enough for covered tomato by any obstacles. Finally, laser detector was added to the visual system that could reduce the position detecting errors within 10mm in X-Y direction and 5mm in Z direction for the covered tomatoes.

• Journal of Biosystems Engineering
• /
• v.27 no.2
• /
• pp.97-106
• /
• 2002

이 연구는 채소의 생산에서 가장 많은 노동력이 소요되고 단순ㆍ반복적인 결속작업의 기계화기술을 개발하기 위하여 수행되었다. 본 논문은 이 연구의 제1보로서 채소의 결속작업실태를 조사분석하여 결속기의 개발방향을 설정하고, 채소의 이송 및 결속끈의 공급장치를 개발한 결과를 수록한 것이다. 채소의 결속작업은 철심이 내장된 끈을 사용하여 타원형으로 결속하고 있었으며, 작업자가 경험적으로 계량하여 결속된 단의 크기는 작물별 차이는 있으나 동일 작물에서 작업자간 차이는 없는 것으로 나타났다. 따라서 결속기는 작업자가 채소를 공급하면 일정 길이의 결속끈을 사용하여 타원형으로 결속하여 배출하는 방식으로 개발한 필요성이 있다고 생각된다. 이를 위해서 결속기는 작업자가 채소를 용이하게 공급할 수 있으며 결속장치까지 흐트러짐이 없이 이송하는 채소의 이송장치, 결속끈의 길이를 조절하여 공급하는 결속끈의 공급장치, 이송된 채소를 결속끈을 꼬아서 타원형으로 결속하는 결속장치 등으로 구성되어야 할 것이다. 채소의 이송장치는 작업자가 채소의 일정량을 용이하게 공급할 수 있도록 폭의 조절이 가능한 트레이를 체인콘베이어에 부착한 구조, 결속끈의 공급장치는 압축력이 걸려 있는 우레탄 재질의 구동 및 종동롤러로 원하는 길이의 결속끈을 피딩하면 칼날로 절단하는 구조로 개발하였다.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.937-946
• /
• 1996

A Far Infrared Ray (FIR) dryer was designed , constructed and tested for red pepper , lycium chinese, and mushroom (Cortiellus shiitake ) drying , and the results were compared to the heated air dryer at the same condition. In the FIR dryer, three different panel materials , galvanized, copper and stainless steel, were used and no ceramic coating and those with ceramic coating (three panels) were 58% , 56%, 64%, and 88% , respectively. The drying times of lycium chinese and mushroom were shortened in FIR dryer by 6 hrs and 4 hrs compared to the heated air drying, respectively. while to remarkable difference in the drying times was found in the red pepper drying . The quality of products was better in FIR dryer where more red color value for red pepper and lycium chinese and more brightness for mushroom . The drying performance of a FIR dryer was superior in terms of total cost of 80,800 WON /100kg of lycium chinese , reduced by 25% compared to the heated air drying.