• 한국재료학회지
• /
• 제8권4호
• /
• pp.328-336
• /
• 1998

본 연구에서는 기지금속과의 고상이나 액상의 고용한이 거의 없는 금속-카본(carbon)계에서 고에너지 볼밀공정을 이용하여 고체 윤활 청동베어링용 Cu-C-X계 나노복합금속분말을 제조하고자 하였다. Cu-10wt.%C-5wt.%AI과 Cu-10wt.%C-5wt.%Fe의 혼합분말을 이르곤 분위기의 attritor내에서 기계적 합금화한 후 Cu-C-X의 나노복합금속분말의 미세조직 특성을 조사하였다. AI, Fe를 첨가하였을 때 10시간 이상의 MA공정에서부터 약 $10\mu\textrm{m}$이하의 미세한 Cu-C-X나노복합금속분말을 얻을 수 있었으며, MA 시간에 따른 분말의 형상과 미세구조 변화는 금속-금속계의 MA 과정과 유사하게 진행되는 것을 알 수 있었다. Cu-C-X 나노복합금속분말의 X-선 회절시험 결과, MA 시간에 따라 Cu와 C분말의 회절피크의 폭은 넓어지고 회절강도는 감소하였으며, 특히 흑연피크의 MA시간에 따른 소멸은 흑연의 낮은 원자산란계수 때문에 의한 X-선 흡수 영향으로 고찰하였다. Williamson-Hall식으로 계산된 Cu-C-X 나노복합금속분말내의 Cu의 결정립은 15시간 이상의 MA공정에서부터 약 10nm이하의 크기를 가졌으며, TEM 분석결과로는 불규칙한 형상의 약 10-30nm 크기로 복합화된 Cu결정립을 확인할 수 있었다.

• 한국수소및신에너지학회논문집
• /
• 제10권1호
• /
• pp.27-40
• /
• 1999

Mg 및 Ni chips을 사용하여 $Mg_2NiH_x$ 수소저장합금을 Planetary Ball Mill M/C로 제조하였으며, 합금화 과정 중에 미치는 분위기 수소압의 영향을 고찰하였다. XRD분석결과 1:30의 장입비에서는 24시간 합성조건일 경우 10 bar이상의 분위기에서 $Mg_2NiH_x$ 상이 발견되었으며 48시간 합성할 경우에는 5 bar 이상의 분위기에서 나타났다. 1:66의 장입 조건에서는 24, 48시간 모두 5 bar 이상의 분위기에서 $Mg_2NiH_x$ 가 검출되었다. 합금화 초기에 만들어지는 것으로 생각되는 $MgH_x$ 로 인하여 전 공정에 걸쳐 미반응 Ni가 잔류하였으며 TG 분석결과 합금화 과정 중에 흡수된 수소저장량은 수소압의 변화에 따라 1.1 ~ 3.9 wt%에 이르는 것으로 나타났다. SEM 관찰 결과 동일 공정 조건에서는 분위기 수소압의 증가가 합금화 결과 최종적으로 얻어지는 미세입자와 그 군집체의 형상 및 크기 변화에 큰 영향을 미치지 못하는 것으로 나타났다.

• 한국재료학회지
• /
• 제28권8호
• /
• pp.435-439
• /
• 2018

MA Al alloys are examined to determine the effects of alloying of Mg and Cu and rolling on tensile deformation behavior at 748 K over a wide strain rate range($10^{-4}-10^3/s$). A powder metallurgy aluminum alloy produced from mechanically alloyed pure Al powder exhibits only a small elongation-to-failure(${\varepsilon}_f$ < ~50%) in high temperature(748 K) tensile deformation at high strain rates(${\acute{\varepsilon}}=1-10^2/s$). ${\varepsilon}_f$ in MA Al-0.5~4.0Mg alloys increases slightly with Mg content(${\varepsilon}_f={\sim}140%$ at 4 mass%). Combined addition of Mg and Cu(MA Al-1.5%Mg-4.0%Cu) is very effective for the occurrence of superplasticity(${\varepsilon}_f$ > 500%). Warm-rolling(at 393-492 K) tends to raise ${\varepsilon}_f$. Lowering the rolling-temperature is effective for increasing the ductility. The effect is rather weak in MA pure Al and MA Al-Mg alloys, but much larger in the MA Al-1.5%Mg-4.0%Cu alloy. Additions of Mg and Cu and warm-rolling of the alloy cause a remarkable reduction in the logarithm of the peak flow stress at low strain rates (${\acute{\varepsilon}}$< ~1/s) and sharpening of microstructure and smoothening of grain boundaries. Additions of Mg and Cu make the strain rate sensitivity(the m value) larger at high strain rates, and the warm-rolling may make the grain boundary sliding easier with less cavitation. Grain boundary facets are observed on the fracture surface when ${\varepsilon}_f$ is large, indicating the operation of grain boundary sliding to a large extent during superplastic deformation.

• 한국재료학회지
• /
• 제10권9호
• /
• pp.642-647
• /
• 2000

Ni-36at.%Al을 함유하는 나도 결정립의 NiAl 합금이 기계적 합금화법에 의해 제조되었다. 제조된 분말은 방전 플라즈마 소결법에 의해 만들어졌다. 상변테에 영향을 주는 인자는 냉각속도와 열처리 시간의 조건으로 논의되었다. 소결체의 상변태 거동은 시차 열분석(DSC)과 X-선 회절(XRD) 분석법에 의해 조사되었다. 미세구조는 주사전자현미경(SEM)으로 관찰되었다. 마르텐사이트 격사상수와 체적 분율은 X-선 회절분석법 중 직접비교법에 의해 계산되었다.

• 한국분말재료학회지
• /
• 제18권5호
• /
• pp.456-462
• /
• 2011

Yttrium oxide is one of the most thermo-dynamically stable materials, so that it is generally used as a dispersoid in many kinds of dispersion strengthed alloys. In this study, a nickel-base superalloy is strengthened by dispersion of yttrium oxide particles. Elemental powders with the composition of Ni-22Cr-18Fe-9Mo were mechanically alloyed(M.A.) with 0.6 wt% $Y_2O_3$. The MA powders were then HIP(hot isotactic press)ed and hot rolled. Most oxide particles in Ni-22Cr-18Fe-9Mo base ODS alloy were found to be Y-Ti-O type. The oxide particles were uniformly dispersed in the matrix and also on the grain boundaries. Tensile test results show that the yield strength and ultimate tensile strength of ODS alloy specimens were 1.2~1.7 times higher than those of the conventional $Hastelloy^{TM}$ X(R), which has the same chemical compositions with ODS alloy specimens except the oxide particles.

• 한국재료학회지
• /
• 제10권10호
• /
• pp.715-720
• /
• 2000

MCFC 작동온도인 $650^{\circ}C$에서 음극의 creep과 소결에 의한 구조적 변형을 막기 위해 기계적 합금법에 의한 Ni-WC분말을 합금화하여 변형에 대한 저항성을 증대시키고자 하였다. 80시간동안 어트리션 밀링을 실시한 분말은 XRD 분석결과 결정규칙이 파괴된 비정질 상을 보였다. 제조된 분말은 적당한 점도의 슬러리로 제조후 테이프 캐스팅법에 의해 green sheet를 제조하였다. 제조된 박판의 두께는 0.9mm였고, 평균 기공 크기는 $3~5{\mu\textrm{m}}$, 기공율은 55%였다. 소결체의 XRD 분석결과 2차성은 생성되지 않았으며, SEM 및 dot-Mapping image를 통해 Ni matrix 안에 W 입자가 미세하고 균일하게 분포되어 있어 고용강화 및 분산강화를 통해 Ni 음극의 기계적 특성을 향상시킬 것으로 기대된다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2000년도 춘계학술강연 및 발표대회 강연 및 발표논문 초록집
• /
• pp.9-10
• /
• 2000

An important business-field of world-wide steel-industry is the coating of thin metal-sheets with zinc, zinc-aluminum and aluminum based materials. These products mostly go into automotive industry. in particular for the car-body. into building and construction industry as well as household appliances. Due to mass-production, the processing is done in large continuously operating plants where the mostly cold-rolled metal-strip as the substrate is handled in coils up to 40 tons unwind before and rolled up again after passing the processing plant which includes cleaning, annealing, hot-dip galvanizing / aluminizing and chemical treatment. In the liquid Zn, Zn-AI, AI-Zn and AI-Si bathes a combined action of corrosion and wear under high temperature and high stress onto the transfer components (rolls) accounts for major economic losses. Most critical here are the bearing systems of these rolls operating in the liquid system. Rolls in liquid system can not be avoided as they are needed to transfer the steel-strip into and out of the crucible. Since several years, ceramic roller bearings are tested here [1.2], however, in particular due to uncontrollable Slag-impurities within the hot bath [3], slide bearings are still expected to be of a higher potential [4]. The today's state of the art is the application of slide bearings based on Stellite\ulcorneragainst Stellite which is in general a 50-60 wt% Co-matrix with incorporated Cr- and W-carbides and other composites. Indeed Stellite is used as the bearing-material as of it's chemical properties (does not go into solution), the physical properties in particular with poor lubricating properties are not satisfying at all. To increase the Sliding behavior in the bearing system, about 0.15-0.2 wt% of lead has been added into the hot-bath in the past. Due to environmental regulations. this had to be reduced dramatically_ This together with the heavily increasing production rates expressed by increased velocity of the substrate-steel-band up to 200 m/min and increased tractate power up to 10 tons in modern plants. leads to life times of the bearings of a few up to several days only. To improve this situation. the Mechanical Alloying (MA) TeChnique [5.6.7.8] is used to prOduce advanced Stellite-based bearing materials. A lubricating phase is introduced into Stellite-powder-material by MA, the composite-powder-particles are coated by High Energy Milling (HEM) in order to produce bearing-bushes of approximately 12 kg by Sintering, Liquid Phase Sintering (LPS) and Hot Isostatic Pressing (HIP). The chemical and physical behavior of samples as well as the bearing systems in the hot galvanizing / aluminizing plant are discussed. DependenCies like lubricant material and composite, LPS-binder and composite, particle shape and PM-route with respect to achievable density. (temperature--) shock-reSistibility and corrosive-wear behavior will be described. The materials are characterized by particle size analysis (laser diffraction), scanning electron microscopy and X-ray diffraction. corrosive-wear behavior is determined using a special cylinder-in-bush apparatus (CIBA) as well as field-test in real production condition. Part I of this work describes the initial testing phase where different sample materials are produced, characterized, consolidated and tested in the CIBA under a common AI-Zn-system. The results are discussed and the material-system for the large components to be produced for the field test in real production condition is decided. Outlook: Part II of this work will describe the field test in a hot-dip-galvanizing/aluminizing plant of the mechanically alloyed bearing bushes under aluminum-rich liquid metal. Alter testing, the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed. Part III of this project will describe a second initial testing phase where the won results of part 1+11 will be transferred to the AI-Si system. Part IV of this project will describe the field test in a hot-dip-aluminizing plant of the mechanically alloyed bearing bushes under aluminum liquid metal. After testing. the bushes will be characterized and obtained results with respect to wear. expected lifetime, surface roughness and infiltration will be discussed.

• 한국분말재료학회지
• /
• 제13권5호
• /
• pp.327-335
• /
• 2006

In the development of new hydrogen absorbing materials for a next generation of metal hydride electrodes for rechargeable batteries, metastable Mg-Ni-based compounds find currently special attention. Amor phous-nanocrystalline $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ alloys were produced by mechanical alloying and melt-spinning and characterized by means of XRD, TEM and DSC. On basis of mechanically alloyed Mg-Ni-Y powders, complex hydride electrodes were fabricated and their electrochemical behaviour in 6M KOH (pH=14,8) was investigated. The electrodes made from $Mg_{63}Ni_{30}Y_7$ powders, which were prepared under use of a SPEX shaker mill, with a major fraction of nanocrystalline phase reveal a higher electrochemical activity far hydrogen reduction and a higher maximum discharge capacity (247 mAh/g) than the electrodes from alloy powder with predominantly amorphous microstructure (216 mAh/g) obtained when using a Retsch planetary ball mill at low temperatures. Those discharge capacities are higher that those fur nanocrystalline $Mg_2Ni$ electrodes. However, the cyclic stability of those alloy powder electrodes was low. Therefore, fundamental stability studies were performed on $Mg_{63}Ni_{30}Y_7$ and $Mg_{50}Ni_{30}Y_{20}$ ribbon samples in the as-quenched state and after cathodic hydrogen charging by means of anodic and cathodic polarisation measurements. Gradual oxidation and dissolution of nickel governs the anodic behaviour before a passive state is attained. A stabilizing effect of higher fractions of yttrium in the alloy on the passivation was detected. During the cathodic hydrogen charging process the alloys exhibit a change in the surface state chemistry, i.e. an enrichment of nickel-species, causing preferential oxidation and dissolution during subsequent anodization. The effect of chemical pre-treatments in 1% HF and in $10\;mg/l\;YCl_3/1%\;H_2O_2$ solution on the surface degradation processes was investigated. A HF treatment can improve their anodic passivation behavior by inhibiting a preferential nickel oxidation-dissolution at low polarisation, whereas a $YCl_3/H_2O_2$ treatment has the opposite effect. Both pre-treatment methods lead to an enhancement of cathodically induced surface degradation processes.