• 한국전산구조공학회논문집
• /
• 제23권5호
• /
• pp.455-463
• /
• 2010

본 연구는 다양한 건설 구조물 중 휨 응력을 받는 부재인 슬래브, 거더 등에 FRP 박스 부재를 적용하기 위한 기초 실험적 연구이다. FRP 부재를 제작하여 FRP 박스 부재의 대형단면으로서의 연결성능 특징을 분석하기 위하여 다양한 조건으로 실험을 수행하였다. FRP 박스 부재의 연결방법에는 화학적 연결, 기계적 연결, 혼합적 연결방법을 이용하여 가로방향과 세로방향에 대해 각각 연결실험을 실시하였다. 실험결과 우레탄+볼트 2개+쉬트를 이용한 방법이 FRP 박스 부재의 가장 이상적인 연결방법이었으며, 유한요소해석을 실시하여 거동을 검토하였다.

• 임산에너지
• /
• 제25권2호
• /
• pp.34-41
• /
• 2006

본 연구에서는 국산 중소경재를 보다 효과적으로 활용하기 위한 목적으로 제재 수율이 높은 대형요소를 이용하여 구조용으로 사용될 수 있는 공학목재를 개발하였다. 중소경 원목으로부터 생산된 상대적으로 큰 단면의 Flitch재를 이용하여 세 가지 기계적 접합방법을 적용한 구조용 대단면 공학목재를 개발하고 휨시험을 통해 그 성능을 평가하였다. 개별 요소를 접합하기 위한 기계적 접합방법으로는 강철 볼트와 목재 다우얼, 철제 래그 볼트가 각각 검토되었다. 개발된 공학목재의 휨성능을 평가한 결과, 강철 볼트를 적용한 경우에 MOR은 평균 $514kgf/cm^2$, MOE는 $129,000kgf/cm^2$ 대표적인 구조용 공학목재인 집성재에 비해 조금 낮거나 유사한 경향을 나타내었다. 목재 다우얼과 철제 래그 볼트를 적용한 경우에는 하중이 증가함에 따라 층재가 분리되어 개별적으로 하중에 저항함으로써 MOR과 MOE 모두가 절반정도로 감소되었다. 본 연구의 결과로부터 대형요소의 기계적 접합으로 제조되는 공학목재의 휨성능은 개별 요소의 접합 성능에 의해 가장 크게 영향 받음을 알 수 있었다.

• 한국농공학회논문집
• /
• 제51권4호
• /
• pp.29-36
• /
• 2009

This is a basic experimental study to apply FRP modular box member to a variety of construction structures exposed to flexural strength, such as a slab and a girder. Applying FRP modular box member to a real structure requires a large section. FRP box member was made into modular systems. Tests were conducted under various conditions in order to analyze jointing performance of the developed FRP modular box member as a large section. For the methods of jointing FRP modular box member, synthetic resins connection, mechanical connection, and a combination of both were used to test both length and breadth connection. As a result of the test, using urethane + two bolts + sheets was the most efficient method of connecting FRP modular box member. It is expected that the proposed joint system in this study will contribute to the increase of failure load and synthesis behavior of FRP modular box member.

• 한국정밀공학회지
• /
• 제33권2호
• /
• pp.121-128
• /
• 2016

The mechanical jointing method is very important in the machine parts and structure. They are used by the bolts and rivet because it is very convenient to replace the parts and the structure. However, the mechanical jointing methods using the bolt and rivet needed the open hole. The machine parts life cycle is reduced because this open hole created the stress concentration. Therefore, the measurement methods are needed to evaluate phenomenon of the stress concentration. This paper discusses the development of the measurement algorithm using the digital image correlation methods to measure the strain distribution of the open hole. To implement the measurement algorithm using the DIC, the LabVIEW 2010 programming tool was used. To measure the strain distribution of the open hole, the tensile specimens having an open hole are made by using the aluminum 6061-T6. To secure the reliability of measurement result using the DIC, the DIC measurement results and FEM analysis results were compared.

• 비파괴검사학회지
• /
• 제23권2호
• /
• pp.148-155
• /
• 2003

저방사화 페라이트강인 JLF는 핵융합로의 블랑켓과 같은 열교환기의 재료로써 유용한 재료이다. 이 재료의 광범위한 적용을 위해서는 JLF강과 다른 재료와의 접합기술의 개발이 중요하다. 최근 두 이종재료간의 접합에는 마찰용접이 많이 이용되고 있으며 본 연구에서도 JLF강과 STS304 간의 마찰용접에 의한 용접특성을 평가하였으며 특히 비파괴기법중의 하나인 음향방출 기법을 이용하여 두 이종재료간의 용접특성 및 최적의 용접조건을 평가하였다. 음향방출 파라미터중의 하나인 카운트와 사상수 등이 최적용접조건 및 용접품질을 평가하는데 유효한 파라미터들이었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2004년도 학술대회지
• /
• pp.39-44
• /
• 2004

A heat and room temperature construction method of asphalt have been mainly applying to rooftop waterproofing in concrete structure, and the rest construction method are sheet, membrane and mortar waterproofing construction method. In particular, joint method in sheet waterproof method is as overlap joint which on being reinforced with fiber and tape, have been applying for job site to mechanical fix using protection disk and anchorage and metal ironwork on the end of sheet. These construction method cause cutting off joint of sheet as behavior of structure according to repairs of sheet itself and thermal conduct, outdoor air environment. In conclusion, we analyzed and examined the application of various sheets and piece ashes about superior 'I' joint which divide from one and the other sheet and progressed about joint construction method of fixing method for overlap.

• 한국정밀공학회지
• /
• 제22권2호
• /
• pp.139-147
• /
• 2005

The lubricant impregnated MC nylon has good frictional properties, but its mechanical strength is inferior to steel for the mechanical elements. For the tribological application Nylon as gears, sliding bearings, cam and etc, the steel shafts are fitted in pre-heated nylon cylinder by a process of interference expansion fit and bonded by induction heating method. The joint shear strength of the two materials was measured by a universal test machine. From the study, the adhesive shear strength between these two materials was affected by the factors of the interference between nylon and steel, the size of nylon cylinder, knurl of steel shaft and inducting heating conditions. The most effective jointing conditions were analyzed and decided for the practical application in the industry.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.285-286
• /
• 2008

In practical applications of HTS tapes for electric devices such as coils and power cables, the jointing of HTS tapes is needed. In magnet applications superconducting joints are needed to achieve very low resistance at the joint, but for power device applications, a slightly higher joint resistance may be acceptable. In this study, an economical joint with good mechanical and electrical integrity could be achieved for Bi-2223 tapes which can be applicable to electric power applications. A lap joint method has been used. The joint resistance and strength of the jointed Bi2223 tapes have been evaluated. Electro-mechanical properties of the joint sample under tension have been examined and compared with the case of the single tapes.

• 한국건축시공학회지
• /
• 제8권6호
• /
• pp.161-166
• /
• 2008

This study is focused on the welding performance of automatic gas pressure welding machine adapted to korean construction site by external appearance investigation. As gas pressure welding is more economical and has good performances compared with other steel bar jointing methods, as arc welding and mechanical joint etc, in Japan, the gas pressure welding is one of the typical connection of steel reinforcement when connecting the D29 and thicker steel bars, But in Korea, gas pressure welding joint method is not widely used caused by the shortage of skilled workers. so to activate the gas pressure welding in Korea, the automatic gas pressure welding machine is developed. In this study, the welding performances of gas pressure welding joint samples using korean automatic gas pressure welding machine are measured by external appearance investigation - blown diameters, blown length, welding face disagreement, central axis eccentric ratio, bending, sag and crack. The results of welding performances on the gas pressure welding joint samples show that samples are satisfied with the standard value regulated in KS D 0244 and JIS Z 3120.

• 터널과지하공간
• /
• 제5권4호
• /
• pp.363-375
• /
• 1995

Critical literature review in this study revealed that there can be a significant influence of the residual stress on the engineering properties of rock. The review also showed that few number of research works on the quantification of the influence was attributed to the limitation of the two classical measurement techniques, viz, X-ray diffraction and mechanical relaxation method. In this study, a new way of approach was sought based on the assumption that residual stress up to the failure. A series of hoop tests conducted onthe samples from the limb of Carboniferous Limestone in Clevedon, England, revealed that (i) there is no preferential orientations of microcracks and minerals which have been widely believed as the main source of the strength anisotropy of rock; (ii) the anisotropy of the tensile strength of the limestone results from the influence of the residual stress; (iii) since jointing commenced within the fold, residual stored strain energy has been released preferentially in the direction perpendicular to the major joints(o$^{\circ}$ and 90$^{\circ}$); (ⅳ) during the hoop test making it much easier to create tensile fracture in these directons, viz 45$^{\circ}$ and 135$^{\circ}$)was released during the hoop test making it much easier to create tensile fracture in these directions, viz 45$^{\circ}$and 135$^{\circ}$;(v) the direction in which the stored strain energy may be presumed to be the least, required the greatest work to cause failure.