• 한국수소및신에너지학회논문집
• /
• 제34권5호
• /
• pp.497-504
• /
• 2023

This study analyzes pressure distribution and pressure drop in the receptacle used in charging system of hydrogen fuel cell vehicles. The objective is to minimize receptacle-induced pressure drop by redesigning internal flow channels. Through numerical simulations, three receptacle variants are compared with a baseline case. Results show reduced pressure drop in the filter section. However, the check valve section exhibits higher pressure drop, requiring further improvement. By increasing throat diameter, pressure drop is decreased by 28% between inlet and outlet of the receptacle. This study shows the relationship between dynamic pressure and pressure drop, providing a guideline for receptacle performance optimization. The redesigned receptacle offers potential for enhancing hydrogen charging efficiency.

• 대한기계학회논문집A
• /
• 제33권5호
• /
• pp.536-543
• /
• 2009

Dynamic behaviour of a package of a microwave oven under the drop-impact conditions is evaluated by the finite element analysis and tests. PAM-CRASH software is used for the finite element analysis and the tests are performed according to the ISTA(International Safe Transit Association) specification. Results of the analyses are compared with those of the tests and accuracy is shown to be favourable. Under the drop-impact condition of the original design, severe deformation occurs and an improved design is proposed to reduce it. The approach presented in this research can be successfully applied to reduce costs and time required to develop new models of the microwave oven.

• 한국소음진동공학회논문집
• /
• 제14권2호
• /
• pp.128-135
• /
• 2004

Generally, heavy electronic products undergo many different types of shocks in transportation from a manufacturer to customers. Cushioning package is used to protect electronic products from severe shock environments. Since the mass distribution of heavy electronic products is usually unbalanced and complex. it is very difficult to design a cushioning package with having high performance by considering only the equivalent stiffness of that. Therefore, when designing the cushioning package for a heavy electronic product, it is necessary to optimize its shape in order to maximize the cushioning performance. In this study, it is focused on designing an optimal shape of cushioning package for a large refrigerator and an efficient design method is suggested by using a dynamic finite element analysis. As the results of this study the optimal shape of cushioning package, which has high cushioning performance and minimized volume, was obtained through the mechanical drop analysis and a optimization process. Through free drop tests of refrigerators, it was identified that the cushioning performance of the cushioning package was improved up by 25% and the its own volume was reduced by 22 ％.

• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.615-621
• /
• 2023

In this study, flow analysis of single, double, and triple filter systems of cylindrical structures was performed to analyze the flow characteristics of each filter. As a result of the flow analysis of the filter system, the number of filters and the pressure drop rate tend to be proportional to each other. It was found that the area passing through the inside of the filter had almost the same pressure. The maximum pressure drop rate of the triple filter system was about 14.9% for the forward-flow and about 12.4% for the reverse-flow. It was determined that the performance of the filter was stable within 20% of the allowable pressure drop rate of the filter system, which is the standard presented to the Korea Water Technology Certification Institute(KWTCI). In the future, a study on the decompression characteristics of the filter system according to the effect of the arrangement interval and filter density of the triple filter will be conducted.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.723-730
• /
• 1998

With the introduction of edge drop control system in Tandem Cold Rolling Mill, it is necessary to develop te numerical expression for the set-up and edge drop automatic control of cold rolled sheet. As a first step we developed a simulation program which predicts profile and the amounts of edge drop at the delivery side of each stand by using roll deformation anlysis with the slit roll model. And by using the program the effect of various rolling conditions on edge drop was investigated. As a result the relations were obtained between the amounts of edge drop and rolling conditions. Based on above relations, the numerical expression was developed for the set-up and automatic control of edge drop by multi-regression of simulation results for the variation of edge drop amount with each rolling condition.

• Journal of Mechanical Science and Technology
• /
• 제19권12호
• /
• pp.2289-2295
• /
• 2005

Two-Phase flow pattern and pressure drop data were obtained for pure refrigerants R134a and R123 and their mixtures as test fluids in a horizontal tube. The flow pattern is observed through tubular sight glasses located at inlet and outlet of the test section. The flow map of Baker developed for air-water two-phase flow at atmospheric pressure failed to predict the observed flow patterns at the higher value of the mass velocity used in the present study. The map of Kattan et al. predicted the data well over the entire region of mass velocity selected in the present study. The measured pressure drop increased with an increase in vapor quality and mass velocity. A new two-phase multiplier was developed from a dimensional analysis of the frictional pressure drop data measured in the present experiment. This new multiplier was found successfully to correlate the frictional pressure drop.

• Journal of Mechanical Science and Technology
• /
• 제15권3호
• /
• pp.403-409
• /
• 2001

The main objective of the present study is to perform an experimental evaluation of five existing correlations for the subchannel pressure drop analysis of a wire-wrapped fuel assembly. For this purpose, a series of water experiments have been performed using a helical wire-wrapped 19-pin fuel assembly for various test parameters. Four different test sections with different pitch to rod diameter ratios (P/D) and wire lead length to rod diameter ratios (H/D) have been fabricated. A series of pressure drop measurements were made to obtain friction factors for these four test sections. The new data along with existing data are used to evaluate existing correlations. Both the original and the simplified Cheng and Todreas correlations give the best agreement with experimental data for all flow regions.

• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.2805-2816
• /
• 1994

This paper describes dynamic finite element analyses performed to study the dynamic behaviors of a shipping container under the impact onto rigid target due to the accidental fall from the hight of 9 m. Using two and three dimensional techniques, the shipping container which gave the maximum damage, ten different drop orientations are considered ; at intervals of $5^{\circ}$ from $45^{\circ}$ to $90^{\circ}$ According to the present results, the orientation of the shipping container which gave the maximum damage is $85^{\circ}$ from horizontal for oblique drop in the primary impact. In the optimal design of the shipping container, the impact limiter material must be considered importantly because it's proper selection affects the weight and the manufacturing cost of the shipping container. The analysis of the shipping container in this paper demonstrated that the shipping container is structurally sound relative to the regulatory drop test requirements.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.250-255
• /
• 2008

This study utilized a high speed lap-shear test to evaluate the mechanical behavior of Sn-37Pb/Cu and Sn-37Pb/Electroless Nickel immersion Gold under bump metallization solder joints under high speed loading and hence the drop reliability. The samples were aged for 120 h at different temperatures ($120^{\circ}C,\;150^{\circ}C,\;170^{\circ}C$) and afterward tested at different displacement rates (0.01 mm/s to 500 mm/s) to examine the effects of aging on the drop life reliability. The combination of the stress-strain graphs captured from the shear tests and identifying a fracture mode dominant in the samples for different strain rates leads us to conclude that the drop reliability of solder joints degrades as the aging temperature increases, possibly due to the role of the IMC layer. This study successfully demonstrates that the analysis based on a high speed lap-shear test could be critically used to evaluate the drop reliability of solder joints.

• International Journal of Aerospace System Engineering
• /
• 제3권2호
• /
• pp.22-25
• /
• 2016

This dissertation tried to analyze passenger behaviors after an accident with the possibilities of a variety of accidents open reflecting the phases of the times of increasing interests in safety of passengers as the use of means of transportation such as cars and airplanes is increasing. Because a lot of data on head-on collisions, broadside collisions and reverse side collisions have been gathered through lots of experiments and interpretations, I chose to study a relatively unfamiliar subject, dropping collision. For example, I tried to study passenger behaviors in seating position after a dropping collision in preparation for falling accidents due to recent frequently-occurring sinkholes, driver's carelessness or mechanical problems. I used MADYMO, passenger behavior interpretation program, and experimented with 2 meters high Drop Test device which I made in person to increase the reliability of the results. On the basis of these, I compared the real experiments with interpretations.