• KSBB Journal
• /
• v.15 no.6
• /
• pp.664-669
• /
• 2000

Micellar aggregates are known to be useful for the selective isolation of biologically active materials such as amino acids, proteins, and enzymes from crude mixtures sparsely dispersed in water. In this study, the effects of pH, salt type and its concentration on the solubilization of $\alpha$-chymotrypsin into the organic micellar phase, which consisted of AOT (sodium 야(2-ethylhexy)sulfosuccinate) and iso-octane, were comprehensively examined. It was found that maximum extraction efficiency was attained at a pH below the isoelectric point of $\alpha$-chymotrypsin; at pH=5.0 for NaCl and KCl, and at pH=7.0 for $CaCl_2$and $MgCl_2$. In order to avoid complications stemming from the precipitationof protein at low pH interfaces, the protein concentrations in the organic and aqueous phases were directly measured. The size of the micelle water pool was estimated by measuring the molar ratio of the surfactant to the water, W(sub)o. The resulting values of W(sub)o were nearly constant at 30 and 19 for NaCl and KCl, respectively, and were independent of pH. The addition of 1:2 salts like $MgCl_2$and $CaCl_2$ led to much lower, but a constant value of, W(sub)o than the 1:1 salts.

• Journal of the Korean Ceramic Society
• /
• v.22 no.1
• /
• pp.35-39
• /
• 1985

Synthetic mica $NaMg_{2.5}(Si_4O_{10})F_2 (Na-TSM)$ was treated with HCl solution and H-type exchange resin to investigate the chemical stability and the ion exchange by measuring the dissolution of chemical components and the exchanged $H^+$ ion. The replacement of $Na^+$ ion occurred in contact with HCl solution and H-type ion exchange resin at the surface of Na-TSM particles reached $Na^+$ ions at maximum value of 70~80%. $Mg^{2+}$ ion of octahedral layer became to dissolve from the pH2 solution and th amount of it dissolved in-creased almost proportional to $H^+$ ion concentration from around 0.02N $H^+$ ion equilibrium concentration. The crystalline structure of Na-TSM was destructed by dissolution of Mg2+ ion in cncentrated hydrochloric acid solution and resulted silica gel precipitation.

• Journal of Korean Society of Forest Science
• /
• v.83 no.1
• /
• pp.32-37
• /
• 1994

Artificial acid rain(pH 3.0, 4.0 and 5.0) and ground water(pH 6.5) were treated on the potted seedlings of Pinus rigida and Pinus koraiensis to examine its effects on the contact angles on needle surface. Artificial acid rain was prepared by diluting sulfuric acid with ground water and ground water(pH 6.5) was used as control. Artificial acid rain was sprayed to the pots two times per week for growing season, one time per week for winter seasons. About 5mm of artificial acid rain was treated each time from late April, 1992 to early October, 1993. Contact angles on the needle surface were measured and compared among the treatments. The results were summarized as follows. Contact angles between needle surface and water droplet decreased with decrease of pH values of artificial acid rain. Measuring and comparing contact angles might be very effective criteria for early diagnosis of acid rain injury in the field.

• Analytical Science and Technology
• /
• v.6 no.5
• /
• pp.435-442
• /
• 1993

Carboxymethylated polyamine-polyurea resin loaded with rubeanic acid (RCCPPI resin) was obtained by 1 step chemical reaction between chlorocarboxymethylated polyamine-polyurea(CCPPI) resin as matrix polymer and rebeanic acid. This resin was confirmed with infrared spectrometry, elemental analysis, and thermal analysis(DSC). The adsorption characteristics of the heavy metal's on the resin were studied by measuring distribution coefficient($K_d$) with changing pH of the solutions and frontal chromatography. The enrichment, recovery, and analysis of trace heavy metals, such as cadmium, cerium, copper, nikel, lead, and zinc, in the presence of high concentrations of sodium, calcium, and acetate salts was possible quantitatively by a column packed with the resin at each optimum pH. Preconcentration factors were more than 25. To elute the adsorbed heavy metals on the resin, 0.025M EDTA solution(pH 9.0) was used.

• Journal of Korean Society of Water and Wastewater
• /
• v.9 no.3
• /
• pp.99-107
• /
• 1995

Various humic substances are widely distributed in natural water body, such as rivers and lakes and cause the yellowish or brownish color to water. The evidence that humic substances are precursors of THMs formation in chlorinated drinking water has been reported m the Jiteratures. For the reason of public health as well as aesthetics, needs for humic substances removal have been increased in the conventional water treatment processes. In this research, the characteristics of aluminium coagulation of humic acids and humic acids were investigated. The optimum pH and coagulants dosage to remove these materials simultaneously by coagulation were alto studied. The results are as followed; 1. UV-254 absorptiometry for measuring the concentration of aquatic humic acids showed good applicability and stable results. 2. The optimal pH range for humic acids removal by aluminium coagulation was 5 to 5.5, however, an increase in aluminium coagulant dosage could enhance the removal rate of humic acids in the wide pH range. 3. Coprecipitation of humic acids in the typical pH range of 6.5 to 8 in water treatment processes may require the sweep coagulation mechanism with the excess aluminium coagulant dosage. 4. Using PAC(poly aluminium chloride) or PASS(poly aluminium silica sulfate) as coagulants was able to expand the operating range for removing humic acids. 5. From the coagulation of humic substances(UV-254) and turbidity at pH range of 5.5 - 6.0 and alum dose of 86 ppm, the removal efficiency of turbidity from the reservoir water was above 90% and that of UV-254 was above 70%. 6. By using the reservoir water, the optimum condition of rapid mixing for simultaneous removal of turbidity and UV-254 absorbance was pH of 5.8 and LAS dose of 86 ppm, in this study.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.9 no.2
• /
• pp.100-109
• /
• 1999

This study evaluates the pretreatment for analysis of benzidine metabolites in urine by measuring the recovery rates according to the temperature and periods of storage of the urine. By the solid phas e extraction, the recovery rates of basic hydrolysis are benzidine 67.4 %, monoacetylbenzidine 105.1 %, and diacetylbenzidine 115.8 %, respectively. By the liquid extraction, the recovery rates of back-extraction into 0.1 M perchloric acid are benzidine 105.7%, monoacetylbenzidine 94.2 %, diacetylbenzidine 72.8 %, respectively. The difference of the recovery rates between the back-extraction into 0.1 M HCl and 0.1 M perchloic acid after basic hydrolysis are 101 % and 98.8 %, respectively. When the recovery rates of the urinary s amples of pH 3, pH 7, pH 12 at $25^{\circ}C$ and $-76^{\circ}C$ are compared for four weeks, there are no differences according to the temperature and the periods of storage. The above results show that the solid phase extraction and back-extraction by 0.1 M perchloric acid after basic hydrolys is are suitable for the analysis of benzidine metabolites. There are no difference of the recovery rates of the urinary samples stored at $25^{\circ}C$ and $-76^{\circ}C$ at pH 3, pH 7, pH 12, respectively for 28 days.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.3
• /
• pp.200-205
• /
• 2013

Pretreatment process is the critical step of RO (Reverse Osmosis) membrane desalination plant in order to prevent RO membrane fouling. The pretreatment as a key component of RO process must be designed to produce a constant and high quality RO feedwater which has low silt density index (SDI). This experiment was conducted to assess parameters affecting SDI value, such as pH, seawater turbidity, temperature, and coagulant dose. The experimental results indicated that the source seawater turbidity did cause little effects on SDI values of filtered water. The 0.45 um hydrophilic membrane was more appropriate than the hydrophobic membrane for measuring SDI. The SDI value was increased with decreasing pH under the condition of below pH 7.0. In addition, the water temperature significantly affected the SDI values, showing higher SDI value with lower water temperature.

• The Journal of Engineering Geology
• /
• v.12 no.4
• /
• pp.439-457
• /
• 2002

Sping waters at 60 sites and groundwaters at 6 wells in Mts. Geumjeong and Baekyang area were investigated for measuring nine physicochemical components (temperature, pH, Eh, EC, TDS, DO, salinity, alkalinity and discharge rate). The pH of spring waters ranges from 5.06 to 8.38, alkalinity from 7.93 to 102.21 mg/ㅣ, electrical conductance from 9.5 to $270{\;}\mu\textrm{s}/cm$, Eh from 64.2 to 685.9 mV, DO from 4.57 to 12.13 mg/l, and the discharge rate from 4.26 to 182.2 ml/s. General statistics was carried out to analyze statistical characteristics of those components. To compare the components with one another, regression analyses were carried out. And the components of spring waters were compared to those of groundwaters. Kriging was used to estimate the spatial variation of DO, pH, Eh, EC, alkalinity and discharge rate in the study area. The kriged isopleth maps were made using normalized kriged values to find anomalies of the physicochemical components and to compare anomalies of different components.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.322-322
• /
• 2010

For boron doping on n-type silicon wafer, around $1,000^{\circ}C$ doping temperature is required, because of the relatively low solubility of boron in a crystalline silicon comparing to the phosphorus case. Boron doping by fiber laser annealing and lamp furnace heat treatment were carried out for the uniformly deposited p-a-Si:H layer. Since the uniformly deposited p-a-Si:H layer by cluster is highly needed to be doped with high temperature heat treatment. Amorphous silicon layer absorption range for fiber laser did not match well to be directly annealed. To improve the annealing effect, we introduce additional lamp furnace heat treatment. For p-a-Si:H layer with the ratio of $SiH_4:B_2H_6:H_2$=30:30:120, at $200^{\circ}C$, 50 W power, 0.2 Torr for 30 min. $20\;mm\;{\times}\;20\;mm$ size fiber laser cut wafers were activated by Q-switched fiber laser (1,064 nm) with different sets of power levels and periods, and for the lamp furnace annealing, $980^{\circ}C$ for 30 min heat treatment were implemented. To make the sheet resistance expectable and uniform as important processes for the $p^+$ layer on a polished n-type silicon wafer of (100) plane, the Q-switched fiber laser used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the fiber laser treatment showed the trade-offs between the lifetime and the sheet resistance as $100\;{\omega}/sq.$ and $11.8\;{\mu}s$ vs. $17\;{\omega}/sq.$ and $8.2\;{\mu}s$. Diode level device was made to confirm the electrical properties of these experimental results by measuring C-V(-F), I-V(-T) characteristics. Uniform and expectable boron heavy doped layers by fiber laser and lamp furnace are not only basic and essential conditions for the n-type crystalline silicon solar cell fabrication processes, but also the controllable doping concentration and depth can be established according to the deposition conditions of layers.

• Journal of the East Asian Society of Dietary Life
• /
• v.21 no.6
• /
• pp.863-870
• /
• 2011

In this study, muffins containing Bokbunja, popularly known as a psychological activator and functional material, was made, and its preference levels and qualitative characteristics were evaluated. We measured the height and weight of muffins containing Bokbunja powder. Height decreased when the volume of Bokbunja powder increased (p<0.001). When weight was measured, there was no meaningful difference between the samples, although the Bokbunja powder-containing samples were heavier than the samples not containing Bokbunja powder. When we measured the weight and specific volume of the muffins containing Bokbunja powder, the specific volume decreased when the amount of Bokbunja powder increased (p<0.001). The moisture and pH levels of the muffins not containing Bokbunja powder were 17.04% and pH 8.59, respectively. As the volume of Bokbunja powder increased, the moisture level of Bokbunja muffin increased while the pH decreased, and there was a significant difference (p<0.001). As a result of measuring the colors of muffins, the brightness of the muffins containing Bokbunja powder decreased, and the muffins showed decreased yellowness index and increased redness. In measuring the texture of Bokbunja muffins, hardness decreased as the volume of Bokbunja power increased (p<0.001). Further, springness of the muffins decreased as the volume of Bokbunja powder increased, and there was a significant difference (p<0.001). The chewiness of the muffins not containing Bokbunja powder was higher than any other muffin sample, and there was a significant difference between the samples (p<0.001). Further, the cohesiveness of the decreased as the volume of Bokbunja powder increased (p<0.001). Bokbunja muffins showed a lower gumminess index than those not containing Bokbunja powder (p< 0.05). When the sensual qualities of the muffins were measured, the color, flavor, taste, and softness of all of the samples showed significant differences (p<0.001), and the muffins containing 8% Bokbunja powder showed the highest sensual quality indexes. When the general preference level for the muffins was measured, the muffins containing 8% Bokbunja powder showed the highest index, 7.03${\pm}$0.96. Based on this result, the ideal volume of Bokbunja powder when making muffins is 8%.