• 한국도로학회논문집
• /
• 제4권1호
• /
• pp.171-181
• /
• 2002

강상판의 포장에 사용되는 구스아스팔트는 시공시 $220^{\circ}C$에서 $260^{\circ}C$의 고온 상태에서 시공되기 때문에 강상판에 과도한 응력 및 변형을 발생시킬 수 있다. 따라서 구스아스팔트의 포설시 강상판에 미치는 열영향을 평가하고 그 영향의 최소화를 위한 포설폭과 패턴을 선정하여야 할 필요가 있다. 본 연구에서는 영종대교 상로도로의 구스아스팔트에 의한 열영향을 평가하기 위하여 일련의 수치해석을 수행하였으며 그 결과를 계측결과와 비교하여 수치해석방법의 타당성을 검증하고, 구스아스팔트가 강상판에 미치는 열영향을 검토하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.88-93
• /
• 1995

The ball screw preloaded for high nigidity and accuracy increases frictional resistance, therefore, its temperature and positioning error rise. In this paper, 2 diamensional temperature distributions of a ball screw with preload are analyzed according to the rotational speeds and stop times by a finite element method. The theremal behaviors of a ball screw are measured to examine the analyzed datum. The examined results show that the trends of temperature rising and axial distributions in steady state are nearly extimate but the temperature low. The differences of temperature ate seems to be caused by not exact heat transfer coefficients. More than an hour is consumed for calculation by FEM. So the modified lumped method for the real-time estimation of the thermal distribution is proposed. The estimated temperature of a ball serw by the modified lumped method is more exactly estimated than by FEM, nd that method takes less than several millisec. Moreover it can be used to estimate heat transfer coefficients.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.329-330
• /
• 2006

The research and development of an actuator are accelerating in the robotics industry. The electricity polymer and SMA actuator are designed simply and are produced a lot of forces per unit volume. Their motions are similar to human's motion, But the repeatability of the electricity polymer actuator is lower. The reaction velocity of the SMA actuator is slow and the travel is short. In this paper, the dynamic characteristic of the segmented SMA is studied. The SMA wire is divided by using the Thermo-electric module(TEM) to control each of segments independently. The MOSFET circuit is used to supply constant currents fer the Thermo-electric module(TEM). The hysteresis and displacement of the SMA wire according to load are measured.

• 한국정밀공학회지
• /
• 제12권10호
• /
• pp.40-49
• /
• 1995

This paper presents the performance and problems in analysis method and testing system of Electronic Speckle Pattern Interferometry (ESPI) method, in measuring two - dimensional in-plane displacement. The anyalysis result of measurement by ESPE is quite comparable to that tof measurement by strain gauge method. This implies that the method of ESPE is a very effective tool in non-contact two-dimensional in-plane strain analysis. But there is a controversal point, measurment error. This error is discussed to be affected not by ESPE method itself, but by its analysis scheme of the interference fringe, where the first-order interpolation has been applied to the points of strain measured. In this case, it is turned out that the more errors would be occurred in the large interval of fringe. And so this paper describes a computer method for drawing when the height is available only for some arbitrary collection of points. The method is based on a distance-weighted, last- squares approximation technique with the weight varying with the distance of the data points.

• 한국정밀공학회지
• /
• 제23권2호
• /
• pp.164-171
• /
• 2006

Anterior cruciate ligament(ACL) injury of the knee is common and a serious ACL injury leads to ligament reconstruction surgery. Gait analysis is used to identify the result of surgery. The purpose of this study is to numerically evaluate and classify knee condition of patients through the chaos analysis. Experiments were carried out for 13 subjects (8 healthy subjects, 5 ACL deficient patients) walking on a treadmill. Sagittal kinematic data of the right lower extremity were collected by using a 3D motion analysis system. The recorded gait patterns were digitized and then coordinated by KWON3D. The largest Lyapunov exponent from the measured knee angular displacement time series was calculated to quantify local stability. It was found that the Lyapunov exponent becomes larger as the knee condition becomes worse. This study suggested a method of the severity of injury and the level of recovery. The proposed method discerns difference between healthy subjects and patients.

• 한국정밀공학회지
• /
• 제9권4호
• /
• pp.90-99
• /
• 1992

In resent year Laser Speckle and its development have enabled surface deformation of engineering components and materials to be interferometrically examined. Laser Speckle- Pettern Interferometry Method is a very useful method for measuring In-plane components of displacement. In measuring thermal expansion coefficient, the various problems generated were established, and the measuring limitation examined. Metarial INCONEL 601 was used in experiments. Specimen was heated to the high temperature(100$0^{\circ}C$) by diong current to the direct two specimen. Then, those problems appear to the influence of back-ground radiation by the heated specimen, the influence by air turbulence, the oxidation of specimen. The color monitor and interference filter prevented the back-ground radiation by rad heat. The oxidation occuring in specimen itself was not generated by the being acid-proof excellence of material INCONEL 601. Yet, in this experiments, the serious problems are the oxidation of specimen and influence by air turbulence. By more reserching these problems forward, it is helpful that the thermal expansion coefficient of many materials is directly measured under high temperature.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권3호
• /
• pp.20-23
• /
• 2007

To calibrate precision autocollimators, the Korean Research Institute of Standards and Science (KRISS) has built a small angle generator using a laser interferometer. The system is based on a sine bar mechanism in which the angle is determined from the ratio of two lengths. The rotational angle is measured by the angle interferometer and the heterodyne laser interferometer detects the relative displacement of two retro-reflectors attached to the rotating arm. The distance between the two retro-reflectors of the laser angle interferometer is self-calibrated by an index table positioned on the rotating arm. The resolution of the system is 0.002 seconds, and the accuracy is better than 0.04 seconds within a measuring range of $\pm$1 degree. The small angle generator can also be used with an index table that can divide one circle into 1440 angles. The combined system can generate any angle over 360 degrees to an accuracy of 0.11 seconds.

• 한국정밀공학회지
• /
• 제16권8호
• /
• pp.138-148
• /
• 1999

Thermal deformations of tension mask under localized heating are analyzed using finite element method and electron beam landing shifts are predicted by the analysis results. In CRT, electron beam landing shifts due to thermal deformations of the tension mask make the color purity of screen worse. In order to get the final results of thermal deformations, firstly the tension processes of the mask and following welding processes between the tensional mask and rail must be analyzed sequentially. And then, nonlinear transient thermo-elastic finite element analysis is performed on every part inside CRT including tension mask, wherein thermal radiation is a main heat transfer mechanism. Because the tension mask has numerous slits, the effective thermal conductivity and effective and effective elastic modulus is calculated, and the tension mask is modeled as a shell without slits. From the displacement results of tension mask, electron beam landing shifts is calculated directly. Experiments are performed to confirm our analysis results. Temperature distributions and beam landing shifts of tension mask are measured and the results are in good agreement with those of analyses.

• Journal of the Korean Wood Science and Technology
• /
• 제26권1호
• /
• pp.87-96
• /
• 1998

The bending performances were evaluated at the radiata pine plywood through veneer compositions encompassing veneer quality, ply-numbers and overlays of the high density- or medium density-phenol resin impregnated sheets (hereafter abbreviated as resin sheets) on the raw plywood. In addition, a prediction on the bending MOE of veneers and plywoods was carried out by the nondestructive testing with stresswave timer. The summarized results were as follows: I. Bending strength and bending MOE of resin sheets-overlaid plywoods in parallel surface grain direction through 5 and 7ply were increased by 13 to 45% and 17 to 34%, respectively. Resin sheets-overlay occurred an increasing effect of the strength efficiency i.e. strength perpendicular-to-grain direction versus that parallel-to-grain direction, showing the phenomenon that the plywood strength becomes greater at the perpendicular-to-grain direction of 7ply than at that of 5ply. Displacement at bending failure had a greater trend at 7ply than at 5ply, and was decreased by resin sheets-overlay. 2. After the nondestructive bending MOEs were measured for individual veneers, these veneers were rearranged in plywood-manufacture. In these plywoods, including resin sheets-overlay, the actual MOE was predictable with feasibility of $R^2$=0.53, and also the nondestructively-evaluated MOE was lower by 20% in raw plywood, and higher 20% in LVL than actual bending MOEs.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.837-844
• /
• 1986

본 논문에서는 우선 실제의 밸브기구를 잘 묘사하고, 감도해석을 적용하기 쉬 운 5자유도의 집중질량 모델을 만들었다. 그리고, 그 모델로부터 얻어지는 밸브양정 을 밸브기구의 고유값 및 고유벡터의 항으로 표시하고, 그것을 설계변수(모델에 포함 되어지는 질량, 강성계수)에 대하여 미분하여 밸브양정의 감도를 구하였다. 그리하 여, 밸브양정에 대한 설계변수들의 영향이 어느정도 되는가를 정량적으로 계산하였다.